Matches Regulations (SOR/2016-182)

Regulations are current to 2017-11-20

Matches Regulations

SOR/2016-182

CANADA CONSUMER PRODUCT SAFETY ACT

Registration 2016-06-22

Matches Regulations

P.C. 2016-609 2016-06-21

His Excellency the Governor General in Council, on the recommendation of the Minister of Health, pursuant to section 37 of the Canada Consumer Product Safety ActFootnote a, makes the annexed Matches Regulations.

Interpretation

Marginal note:Definitions

 The following definitions apply in these Regulations.

ignition compound

ignition compound means the chemical compound used to cover the end of the splint of the match and to make the match head. (corps inflammable)

lot

lot means a stock, batch, shipment or delivery lot of matches. (lot)

striking surface

striking surface means that part of a book, box or other container of matches that is for the purpose of igniting matches. (frottoir)

wood matches

wood matches do not include wood matches that are attached to a common base. (allumette en bois)

Specifications

Marginal note:Matches
  •  (1) Matches must meet the following requirements:

    • (a) the match must not contain any white phosphorus;

    • (b) the ignition compound must be uniformly applied; and

    • (c) the match head must not be chipped, cracked or crumbling and must not adhere to the head of another match.

  • Marginal note:Additional requirement — wood matches

    (2) The splint of a wood match must be made of good grade and long-fibre wood and must not be broken, split or crushed.

Marginal note:Matchbooks

 A matchbook must meet the following requirements:

  • (a) its cover must, when closed, cover all the match heads;

  • (b) any fastening wire used to secure its cover to the common base of the matches must not pierce or loosen the striking surface;

  • (c) any friction paint on the inside of the cover must not be present within 2.54 cm of the match heads; and

  • (d) its striking surface must be on the side that is opposite to the side that opens.

Marginal note:Spontaneous ignition

 Matches must not ignite spontaneously when tested in accordance with Schedule 1.

Marginal note:Non-disintegration of ignition compound

 The ignition compound must not, when ignited, crack, explode or drop as glowing particles from the match.

Marginal note:Afterglow

 The splint of a match must not glow for more than three seconds after the flame has been extinguished.

Marginal note:Breaking resistance of splints

 When tested in accordance with Schedule 2, the splint of a match must withstand the following moments without breaking:

  • (a) in the case of a wood match, 700 gf∙cm;

  • (b) in the case of a round match other than a wood match, 100 gf∙cm; and

  • (c) in any other case,

    • (i) 300 gf∙cm, when the match is placed on its edge, and

    • (ii) 100 gf∙cm, when the match is placed flat.

Information

Marginal note:Name and mailing address

 Every matchbook, box or other container that immediately covers or encloses the matches must carry on it the name and mailing address of the following, in a clear and legible manner:

  • (a) the manufacturer, if the matches are manufactured in Canada; or

  • (b) the importer or distributor, if the matches are imported.

Compliance

Marginal note:Matches

 In order to determine whether a lot of matches complies with the requirements of paragraphs 2(1)(b) and (c), subsection 2(2) and sections 5 to 7, the following procedures are to be used:

  • (a) select at random, based on the number of matches in a lot set out in Column 1 of Table 1 of Schedule 3, a sample that consists of the number of matches set out in Column 2;

  • (b) if a match fails to meet any requirement set out in sections 5 to 7, determine that the match has a major defect;

  • (c) if a match fails to meet a requirement set out in paragraphs 2(1)(b) or (c) or subsection 2(2), determine that the match has a minor defect; and

  • (d) if the number of matches having a major defect is equal to or greater than the number of matches set out in Column 3 of the same table, or if the number of matches having a minor defect is equal to or greater than the number of matches set out in Column 4 of that table, determine that the lot does not comply with the requirements set out in paragraph 2(1)(b) or (c), subsection 2(2) or any of sections 5 to 7, as the case may be.

Marginal note:Matchbooks

 In order to determine whether a lot of matchbooks complies with the requirements of paragraphs 3(a) to (c), the following procedures are to be used:

  • (a) select at random, based on the number of matchbooks in a lot set out in Column 1 of Table 2 of Schedule 3, a sample that consists of the number of matchbooks set out in Column 2;

  • (b) if a matchbook fails to meet any requirement in paragraphs 3(a) to (c), determine that the matchbook has a defect; and

  • (c) if the number of matchbooks having a defect is equal to or greater than the number of matchbooks set out in Column 3 of the same table, determine that the lot does not comply with one or more of the requirements set out in paragraphs 3(a) to (c).

Repeal

 [Repeal]

Coming into Force

Marginal note:Registration

 These Regulations come into force on the day on which they are registered.

 
Date modified: