Oil and Gas Storage Tanks and Containers
(a) all gases likely to prove injurious to each workman have been removed;
(b) such workman has been equipped with an air line mask or other breathing apparatus and whatever equipment is used must be of a type approved by the Oil Conservation Engineer; and
(c) such workman has been supplied with a rope that has been made fast to his body and also to a substantial support on the outside of the tank or other container; such rope must be of sufficient length to reach from the support on the outside to any point of work in the tank or container and shall be of sufficient strength to bear the weight of the workman, and the workman shall be attended by two men whose duty it is to stay on the outside of the tank and to keep a close watch over the workman inside.
(2) All work in any confined space where conditions are such as to produce nausea or indisposition on the part of the workman shall be arranged in short shifts with the men on the outside alternating with the workman inside.
(3) No flashlights or lanterns other than those that are approved for such use by the Oil Conservation Engineer shall be used around gas or oil wells.
79 (1) All electrical installations at or within 75 feet of any drilling rig, well, separator, crude petroleum storage tank or other unprotected source of ignitable vapours shall be in accordance with the standards prescribed by the Canadian Electrical Code, except where those standards do not conform with the provisions of these Regulations.
(2) In lighting installations
(a) all wiring shall be in
(b) all switching and overcurrent protection shall be enclosed in a vapour-proof cabinet with all conductor raceways entering the cabinet properly sealed;
(c) all extension cords shall be so connected that accidental disconnection is impossible and when cord receptacle of the lock and switch type are not provided, instructions shall be issued to turn off the current before connecting or disconnecting extension cords;
(d) all lamps shall be provided with guards approved by the Oil Conservation Engineer; and
(e) all service conductors shall be enclosed in rigid, threaded and vapour-proof conduit or lead-covered or aluminum-covered cable extending at least 75 feet horizontally from any drilling rig, well, separator, crude petroleum storage or other unprotected source of ignitable vapours.
(3) In power installations
(a) all wiring shall be in
(b) all switches, control and overcurrent protective devices shall be of a vapour-proof type if fitted inside a derrick or derrick building or within 75 feet of any well, separator, crude petroleum storage or other unprotected source of ignitable vapours.
(4) Electric generators, motors and heaters within 75 feet of a drilling rig or well or of equipment in which ignitable vapours are contained shall be of totally enclosed construction.
(5) Electrical installations shall be properly maintained at all times.
Illumination of Rigs
80 Lighting shall be sufficient to provide at all times for a minimum illumination of
(a) five foot candle power on all of the derrick floor;
(b) three foot candle power at the fourble board, pumps and catwalk; and
(c) one foot candle power at the shale shaker, stairways and other working areas.
Control of Static Electricity
81 Metallic parts of containers and conductors of flammable fluids shall be in electrical contact with and connected to the ground in such manner as will prevent development of static electric charges.
82 (1) Each drilling rig shall have not less than two 20-pound dry powder extinguishers and each boiler house shall have not less than two five-gallon non-freeze type fire extinguishers all of which shall be kept in good working condition.
(2) When a steam pressure of 100 pounds or more is used on or about any rig, there shall be placed in the derrick room thereof, apart from other snuff line, a steam hose of a diameter of not less than one inch and a length of hose of not less than 20 feet, securely connected to a steam line with the valve situated close to the exit therefrom.
(2) An employee, when working in an area where gas accumulations may present a hazard, shall use an air line mask or other breathing apparatus.
(3) All breathing apparatus shall be tested once in each month and the result of this test entered in a log book, or if the apparatus is provided in connection with a drilling operation, in the Rig Record Book, and the entry signed by a person authorized by the owner or operator of the apparatus.
Smoking and Fires
(2) No fire shall be located less than 75 feet from any drilling rig, well or from any equipment in which ignitable vapours are contained.
(3) Any fire that is set shall be safeguarded by mechanical or other means so that no hazard to surrounding property is created.
(4) All waste material shall be burned in a manner so as not to create a fire hazard to wells, tanks or other equipment containing ignitable vapours or disposed of in such a manner so as not to pollute any stream or fresh water stratum.
(5) No heating or lighting apparatus involving the use of a flame or exposed electrical element shall be brought into a drilling rig doghouse.
(6) No stove, open flame heater or electric heater with exposed elements shall be used within 75 feet of any drilling rig, well or of any equipment in which ignitable vapours are contained.
(7) Steam boilers or open flame steam generators shall be located at a point not less than 150 feet distant from a well or any equipment containing ignitable vapours and on the side from which the prevailing wind blows.
(8) On all internal combustion engines on a derrick floor or in a drilling engine room or within 75 feet of any equipment containing ignitable vapours
(a) the exhaust systems, where the temperature of the parts in contact with hot gases exceeds 400°F, shall be thermally insulated and covered by metal so that no liquids can be absorbed by the insulating materials;
(b) engine air inlets shall be fitted with flame arrestors if located within 40 feet of a well head and the final engine exhaust to atmosphere shall be fitted with a flame trap if situated within 40 feet of the well head unless otherwise directed by the Oil Conservation Engineer;
(c) the exhaust pipes shall be directed away from the well or any equipment containing ignitable vapours; and
(d) the manifolds shall be shielded to prevent contact with liquids which might fall thereon.
(9) The cylinders, valve chests and other hot exposed parts of steam engines and steam pipes on a derrick or in a drilling engine room or within 75 feet thereof, whenever the steam temperature exceeds 400°F, shall be fitted with thermal insulation and the insulation shall be covered by metal so that no liquid can be absorbed by the insulating materials.
(2) Drainage from such a location shall be such that the flow is in a direction away from the location of such well.
Drill Stem Tests
86 Unless a rig is adequately lighted by natural light or by means of floodlights having no electrical equipment capable of igniting gas or oil within 75 feet of the well head, no drill pipe shall be disconnected during a drill stem test unless there is no possibility of any oil or gas being present in the drill pipe.
87 In addition to its regular means of attachment, every test plug shall be equipped with a safety line and attached thereby to the links when above the derrick floor.
- Date modified: