China Surtax Remission Order (2024)
Version of the schedule from 2025-06-26 to 2025-10-14:
SCHEDULE 1(Subsection 1(1) and paragraph 1(2)(a))
| Column 1 | Column 2 | |
|---|---|---|
| Item | Tariff Item | Description of Goods |
| 1 | 7210.70.00 | Pre-painted galvalume coils, of grade 33, of specification ASTM A792 or AZ50 (AZM150), with a thickness of 24 gauge, 26 gauge or 30 gauge, a width of 48 inches and an SMP or PVDF coating |
| 2 | [Repealed, SOR/2025-114, s. 2] | |
| 3 | [Repealed, SOR/2025-147, s. 1] | |
| 4 | [Repealed, SOR/2025-147, s. 1] | |
| 5 | 7219.23.00 | Stainless steel sheets and plates, hot-rolled with 2B finish, of type 304 or 304L, with 11 gauge thickness, width of 5 feet, length of 20 feet, of specification ASTM A240 |
| 6 | 7219.23.00 | Stainless steel sheets and plates, hot-rolled with 2B smooth finish, of type 304 or 304L, with 11 gauge thickness, width of 6 feet, length of 12 feet, of specification ASTM A240 |
| 7 | 7219.31.00 | Stainless steel sheets and plates, cold-rolled with 2B smooth finish, of type 304 or 304L, with 3/16 inch thickness, width of 5 feet, length of at least 10 feet but not exceeding 20 feet, of specification ASTM A240 |
| 8 | 7220.20.00 | Flat-rolled stainless steel products, with a width of less than 600 mm, not further worked than cold-rolled (cold-reduced), for use in the production of goods classified under tariff item 7310.10.00 |
| 9 | [Repealed, SOR/2025-147, s. 2] | |
| 10 | 7222.20.00 | Stainless steel metric round bars, of type 304, cold-rolled, h9 tolerance, with an outer diameter of 16 mm, 20 mm, 25 mm, 30 mm, 35 mm, 40 mm, 50 mm or 60 mm, of specification ASTM A276 |
| 11 | 7222.30.00 | Stainless steel metric square bars of 30 mm or 40 mm, of type 304, cold-rolled, of length 4000 mm, of specification ASTM A276 |
| 12 | 7223.00.00 | Stainless steel lashing wire or rebar tie wire |
| 13 | 7223.00.00 | Ultra-fine stainless steel wire, with a diameter of 0.15 mm or 0.28 mm |
| 14 | 7225.11.00 | Silicon grain-oriented steel, with a width of 600 mm or more |
| 15 | 7225.99.00 | Specialty steel products: S-7 VRM steel plates, D-2 VRM steel plates or A-2 VRM steel plates |
| 16 | 7226.11.00 | Silicon grain-oriented steel, with a width of less than 600 mm |
| 17 | 7226.19.00 | Silicon amorphous steel, with a width of less than 600 mm |
| 18 | 7226.99.00 | Specialty steel products of grade 4140, heat-treated, annealed |
| 19 | 7228.30.00 | Round specialty steel products, of the following grades: of grade 4340, heat-treated, of grade 8620, of grade 3312, hot-rolled, annealed, of grade 1045, hot-rolled, of grade 1018, hot-rolled or of grade EN30B |
| 20 | 7228.40.00 | Alloy steel bars and rods |
| 21 | 7228.50.00 | Other bars of other alloy steel, not further worked than cold-formed or cold-finished |
| 22 | 7304.19.00 | Unfinished seamless carbon or alloy steel line pipes in the form of mother tubes with an outside diameter of 184, 197, 210, 235, 260, 286, 328, 350, 368, 377, 394, 402, 419, 426, 450, 475, 480, 500, 521, 530, 560, 585 or 610 mm, a wall thickness of at least 9 mm but not exceeding 110 mm and a length of at least 7.72 m but not exceeding 15.24 m, not stenciled as meeting any line pipe product specification, but suitable for use in the production, and not solely the finishing, of seamless line pipe made to any one or more of the following specifications: API 5L, CSA Z245.1, ISO 3183, ASTM A333, ASTM A335, ASTM A106, ASTM A53 or their equivalent |
| 23 | 7304.23.00 | Drill pipes, other than of stainless steel, of specification API 5DP or API 7-1 |
| 24 | 7304.29.00.79 | Tubes, pipes and hollow profiles, seamless, of iron — other than cast iron — or steel: coupling stock, with an outside diameter of at least 2.875 inches but not exceeding 37 inches |
| 25 | 7304.59.00.60 | Alloy mechanical tubes of grade 4140 or 4130 Mod, of specification ASTM A519, with an external diameter of at least 3.5 inches but not exceeding 10 inches, a wall thickness of at least 0.3 inches but not exceeding 1.5 inches, and black lacquer protective coating |
| 26 | 7306.40.00.10 | Stainless steel tubes, circular, of type 304L, with an external diameter not exceeding 25.3 mm |
| 27 | 7306.40.00.20 | Stainless steel tubes, circular, of type 304L, with an external diameter exceeding 25.3 mm but not exceeding 114.9 mm |
| 28 | 7306.61.00.39 | Steel tubes — other than galvanized — rectangular, of type 304L, with an external periphery not exceeding 812.8 mm |
| 29 | 7604.21.00 | Aluminum alloy hollow profiles with a powder coating finish on the interior and exterior surfaces |
| 30 | 7604.29.00 | Aluminum alloy bars, rods and profiles: Die #C300X110, Die #C410X110 or Die #1693 |
| 31 | 7605.19.00 | Non-alloyed aluminum wire, with cross-sectional dimension not exceeding 7 mm, of grade AL-1350, compliant with the chemical requirements referred to in Table 2 of specification ASTM B233-97, of any of the following dimensions:
|
| 32 | 7606.11.00 | Non-alloyed aluminum plates, sheets and strip, with a thickness exceeding 0.2 mm, rectangular, compliant with specification ASTM B209 or equivalent industry specifications, flat 2 mm per metre in all directions, with diagonals that do not measure a difference of more than 4 mm, no visible ripples on any sheet and no scratches, gouges or residual oils |
| 33 | 7606.11.00 | Non-alloyed aluminum plates, sheets and strip, with a thickness exceeding 0.2 mm, rectangular, used as cathode sheets in zinc electrowinning processes |
| 34 | 7606.11.00 | Non-alloyed aluminum plates, sheets and strip, rectangular, of grade 1050 Aluminum “O” Coil or grade 1350 Aluminum “O” Coil, compliant with the chemical requirements of specification ASTM B233-97, with a thickness of at least 0.020 inches but not exceeding 0.060 inches, a width of at least 2 inches but not exceeding 33.5 inches, and a mill finish |
| 35 | 7606.12.00 | Aluminum alloy plates, sheets and strip, of a thickness exceeding 0.2 mm, rectangular |
| 36 | 7606.12.00.11 | Aluminum checker plate sheets of alloy 3003, with a base thickness of 4 mm, width of 4 feet and length of 10 feet |
| 37 | 7606.12.00.11 | Pre-painted aluminum coils, 3003–H24 with 8 or 12 µm polyester coating in black, brown or white, with a thickness of 0.5 mm and width of 610 mm |
| 37.1 | 7606.12.00.11 | Aluminum coils of alloy 5005, H14 or H34, anodized quality, not clad, with a thickness exceeding 0.2 mm but less than 7 mm |
| 38 | 7606.12.00.12 | Aluminum alloy plates, sheets and strip, with a thickness of 7 mm or more, rectangular, not clad, compliant with specification ASTM B209 or equivalent industry specifications, flat 2 mm per metre in all directions, with diagonals that do not measure a difference of more than 4 mm, no visible ripples on any sheet and no scratches, gouges or residual oils |
| 38.1 | 7606.12.00.12 | Aluminum coils of alloy 5005, H14 or H34, anodized quality, not clad, with a thickness of 7 mm or more |
| 39 | 7607.19.00.00 | Aluminum foil, with a thickness not exceeding 0.2 mm, not backed, other than rolled but not further worked, of alloys 3003, 3004, 3104, 8011 or 8111 |
| 40 | 7609.00.00 | Aluminum tube or pipe fittings, of the following specifications:
Cylindrical shape, of the following grades and specifications:
|
Note If the description in column 2 covers only a subset of goods classified under the tariff item referred to in column 1, remission is granted only for the goods described in column 2.
- SOR/2025-114, s. 2
- SOR/2025-114, s. 3(E)
- SOR/2025-114, s. 4(F)
- SOR/2025-114, s. 5(E)
- SOR/2025-114, s. 6
- SOR/2025-114, s. 7
- SOR/2025-147, s. 1
- SOR/2025-147, s. 2
Page Details
- Date modified: