United States Surtax Remission Order (2025)

• (a) Instantized whey protein concentrate, with a minimum 80% protein on a dry basis;

• (b) Instantized whey protein hydrolysate, with a minimum 80% protein on a dry basis and a level of hydrolysis of 1 to 4%;

• (c) Whey protein concentrate 80%

• (a) Instantized whey protein isolate with a minimum of 90% protein on a dry basis;

• (b) Whey protein isolate 90%;

• (c) Hydrolyzed whey protein concentrate 80%

• (a) Flat-rolled products of carbon steel, in coils, hot-rolled, pickled and oiled, of grade A506 4130 annealed, of a minimum spheroidization of 95%, with a width of 600 mm or more, of a thickness of at least 3.98 mm but not exceeding 4.20. mm;

• (b) Flat-rolled products of carbon steel, in coils, hot-rolled, pickled and oiled, of grade WSS M1A365 A5, of a width of 600 mm or more, of a thickness of at least 3.54 mm but not exceeding 3.65 mm;

• (c) Flat-rolled products of high-carbon steel, in coils, of grades 1050 or 1035, of specification SAE J403, of a thickness of 0.114 or 0.118 inch, of a width of at least 43.275 inches but not exceeding 51.375 inches, pickled, dry and spheroidize annealed

• (a) Flat-rolled products of carbon steel, in coils, hot-rolled, pickled and oiled, of grade SAE J2340 490XF or 550XF, of a thickness of at least 1.06 mm but not exceeding 1.58 mm, of a width of 600 mm or more;

• (b) Flat-rolled products of steel, hot-rolled, in coils, of specifications SAE J2340 340XF, 420XF, 490XF, 550XF, and ASTM A606 Type 4, of a thickness of at least 0.049 inch but not exceeding 0.108 inch, whether or not slit, with slit widths of at least 3.018 inches but not exceeding 35.700 inches, with full coil widths of at least 36.000 inches but not exceeding 54.375 inches

• (a) Flat-rolled products of carbon steel, in coils, hot-rolled, of grade SAE J403 1050, spheroidized annealed, of a thickness of at least 0.090 inch but not exceeding 0.097 inch, with a width of 48 inches, with a hot-rolled surface finish;

• (b) Flat-rolled products of carbon steel, in coil, hot-rolled, of grade SAE J403 1037, of a thickness of at least 0.055 inches but not exceeding 0.071 inch, of full coil widths of at least 47.500 inches but not exceeding 48.375 inches, of slit widths of at least 6.75 inches but not exceeding 24.00 inches, with a hot-rolled surface finish

• (a) Flat-rolled products of carbon steel, in coils, not further worked than cold-rolled (cold reduced), of grade SAE J2340 550Y, JIS G3135 SPFC 590 or GMW 3032 M-ST-S 210B2, of a thickness of at least 1.00 mm but not exceeding 1.68 mm, of a width of 600 mm or more, uncoated;

• (b) Flat-rolled products of carbon steel, in coils, not further worked than cold-rolled (cold reduced), of grade SAE J403 1050, fully annealed, with 95% minimum spheroidization, of a thickness of at least 2.54 mm but not exceeding 2.70 mm, with a width of 600 mm or more

• (a) Flat-rolled products of carbon steel, in coils, not further worked than cold-rolled (cold reduced), of grade GMW 3032 M - ST-S 210B2 or GMW3032M-ST-S-CR180B2, of a thickness of at least 0.74 mm but not exceeding 1.00 mm, with a width of 600 mm or more;

• (b) Flat-rolled products of non-alloy steel, in coils, cold-rolled (cold-reduced), of a specification SAE J2340 340XF, of a thickness of at least 0.019 inch but not exceeding 0.022 inches, with a slit width of 23.425 inches, with a full coil width of 48 inches, gauge range from 0.019 to 0.022 inch, with a pickled and oiled finish

• (a) Flat-rolled products, in coils, sheets and plates of carbon steel, electro-galvanized, of grade WSS-M1A365-A14 CR4 60g/60g u/o Exposed, with a width of 600 mm or more;

• (b) Flat-rolled products, in coils, of non-alloy steel, cold-rolled, electro-galvanized, of grade M-190, of specification ASTM A980, with a thickness of at least 0.028 inch but not exceeding 0.031 inch, with a width 50.5 inches, with a slit width of 9.95 inches, with a zinc coating ZN132, unpassivated and oiled finish;

• (c) Flat-rolled products, in coils, of carbon steel, of grade 1006, with a thickness of at least 1.44 mm, with a width of 600 mm or more, hot-dipped, galvanized and chemically treated dry

• (a) Flat-products, in coils, sheets and plates, of non-alloy steel, cold-rolled, galvanized, of grade ASTM A1008 J2329, with a width of 600 mm or more, of a thickness of at least 0.80 mm but not exceeding 0.91 mm;

• (b) Flat-rolled products, in coils, of low-alloy steel, galvanized, of specification SAE J2340 550XF, of a thickness of at least 0.0374 inch but not exceeding 0.0413 inch, with a slit width of 21.8504 inches, with a full coil width of 44.100 inches, with a hot-dip galvanized coating, unpassivated and oiled;

• (c) Flat-rolled products, in coils, of galvanized steel, of specification SAE J2340 250B, of a thickness of at least 0.044 inch but not exceeding 0.049 inch, with a slit width 8.431 inches, with a full coil width of 42.655 inches, with a hot-dip galvanized coating, unpassivated and oiled;

• (d) Flat-rolled products, in coils, of galvanized low-alloy steel, of specification SAE J2340 550XF, of a thickness of at least 0.047 inch but not exceeding 0.049 inch, with a slit width of 35.19 inches, with a full coil width of 43.7 inches, with a hot-dip galvanized coating, unpassivated and oiled;

• (e) Flat-rolled products, of steel strip in oscillated coils, galvanized, of a standard CSA C22.2 No. 56-17 Section 7.2.2, with a depth of 0.0170 inch or 0.0185 inch, with a width of 0.3560 inch or 0.0394 inch

• (a) Flat-rolled products, of non-alloy steel, galvanized with zinc, not corrugated, with a thickness of at least 1.849 mm but not exceeding 2.052 mm, of a width of at least 662 mm but not exceeding 989 mm, with a zinc coating or a zinc phosphate conversion coating, with a surface finish;

• (b) Flat-rolled products, of non-alloy steel, cold-rolled, not corrugated, of a thickness of at least 1.275 mm but not exceeding 1.326 mm, of a width of at least 1 073 mm but not exceeding 1 076 mm, electrogalvanized with zinc, with a zinc coating and surface finish

• (a) Flat-rolled steel, in coils, of specification CSA G401-24, of a thickness of 1.6, 2.0 or 2.8 mm, of a width of 690 mm, 692 mm or 863 mm, with an aluminium and zinc coating of 1 ounce per square feet;

• (b) Flat-rolled products, in coils, sheets or plates, of carbon steel, of grade ASTM A463 CQ T-125, with a width of 600 mm or more, plated or coated with aluminum-zinc alloys

• (a) Flat-rolled products of iron or non-alloy steel, cold-rolled, not clad, plated or coated, of a thickness not exceeding 0.0098 inch, of a width not exceeding 23.625 inches, of grade AISI 1045, 1050, 1055, 1067 to 1070 or 1075, of specification ASTM A682 or ASTM A684;

• (b) Flat-rolled steel strips, cold-rolled and annealed, of high-carbon SAE 1095 spring steel, of a thickness of 0.9 mm, of a width of 500 mm;

• (c) Flat-rolled products, of spring-steel strip, hardened and tempered, of grade SAE/AISI 1095, of a thickness of at least 0.2 mm but not exceeding 2.5 mm, uncoated but lightly oiled

• (a) Continuous cast iron bars of grade 65-45-12, 65-40-18, 60-55-06, with a circular cross-sectional diameter of at least 0.5 inch up but not exceeding 20 inches, with a rectangular cross-section of a width of at least 1 inch but not exceeding 20 inches, a length of at least 2 inches but not exceeding to 40 inches;

• (b) Special quality bars and rods of non-alloy steel, not further worked than forge, hot-rolled, of a diameter of at least 1 inch but not exceeding 10 inches, of grade 1018, 1020, 1022, 1040, 1045, 1055, ASTM105, ASTM108, ASTM350, ASTM36, or SA105 (VAR- vacuum degassed)

• (a) Bars and rods of free cutting steel, cold formed, of a diameter of 1.46 inches, of grade B 1018;

• (b) Bars and rods of free cutting steel, cold formed, of a diameter of 1.312 inches, of grade 10B21;

• (c) Bars and rods of free cutting steel, cold formed, of a diameter of 1 inch, of grade SAPH P and 1022;

• (d) Bars and rods of free cutting steel, cold formed, of a diameter of 1.078 inches, of grade 1022

• (a) Bars and rods of cast iron, continuous, not further worked than cold-formed or cold-finished, of grade 65-45-12, 65-40-18 or 60-55-06, with a circular cross-sectional diameter of at least 0.5 inch but not exceeding 20.0 inches or with a rectangular cross-section of a width of at least 1 inch but not exceeding 20 inches and a length of at least 2 inches but not exceeding to 40 inches;

• (b) Bars, cold-rolled, of grade C1018 or C1045, of a thickness of at least 0.75 inch but not exceeding 4 inches, of a length of 20 feet;

• (c) Bars, cold-rolled of grade C1045, of yield of 90 ksi, of a thickness of 2.125 inches, of a length of 20 feet;

• (d) Other bars, of iron or non-alloy steel, not further worked than cold-finished, including ground, turned or polished, of grade 1018, without coating or plating

• (a) Flat-rolled products of other alloy steel, in coils, hot-rolled, pickled and oiled of grade 420XF (modified), according to specification WSS M1A365 A5, with a width of 600 mm or more, of a thickness of at least 3.54 mm but not exceeding 3.65 mm;

• (b) Flat-rolled products of other alloy steel, in coils, hot-rolled, pickled and oiled of grade 550XF, of specification SAE J2340, with a width of 600 mm or more, of a thickness of at least 1.42 mm but not exceeding 1.58 mm;

• (c) Flat-rolled products of other alloy steel, in coils not further worked than hot-rolled of grade 4130, with a width of 600 mm or more, of a thickness of at least 3.98 mm but not exceeding 4.20 mm, pickled and oiled, annealed;

• (d) Flat-rolled products of other alloy steel, in coils, hot-rolled, pickled and oiled of grade 490XF, of specification SAE J2340, with a width of 600 mm or more, of a thickness of at least 1.06 mm but not exceeding 1.27 mm;

• (e) Flat-rolled products of alloy steel, in coils, hot-rolled, pickled and oiled, of grade SAE J2340 490XF, of specification SAE J2340, with a width of 600 mm or more, of a thickness of at least 1.49 mm but not exceeding 1.71 mm;

• (f) Flat-rolled products of other alloy steel, in coils, not further worked than hot-rolled, of grade 550X, 420XF or 340XF, of specification SAE J2340, of a minimum thickness of at least 0.055 inch but not exceeding 0.059 inch, of a width of at least 44.00 inches but not exceeding 53.46 inches

• (a) Flat-rolled products of other alloy steel, in sheets and plates, hot-rolled, pickled and oiled of grade 420XF (modified) according to specification WSS M1A365 A5, with a width of 600 mm or more, of a thickness of at least .54 mm but not exceeding 3.65 mm;

• (b) Flat-rolled products of other alloy steel, in sheets and plates, hot-rolled, pickled and oiled of grade JIS G3113 SAPH 440, with a width of 600 mm or more, of a thickness of at least 2.26 mm but not exceeding 2.30 mm;

• (c)   Flat-rolled products of other alloy steel, in sheets and plates, hot-rolled, pickled and oiled of grade SAE J2340 340XF, with a width of 600 mm or more, of a thickness of at least 1.49 mm but not exceeding 1.66 mm;

• (d) Flat-rolled products of other alloy steel, in sheets and plates, hot-rolled, pickled and oiled of grade 550XF, of specification SAE J2340, with a width of 600 mm or more, of a thickness of at least 1.70 mm but not exceeding 1.91 mm;

• (e) Flat-rolled products of other alloy steel, in sheets and plates, hot-rolled, pickled and oiled of grade 490XF, of specification SAE J2340, with a width of 600 mm or more, of a thickness of at least 1.49 mm but not exceeding 1.71 mm;

• (f) Flat-rolled products of other alloy steel, not further worked than hot-rolled, of grades 4140, 1018, 1020, 1045, A2, D2, H13, L6, O1, P20, S7, M2, M7, M42, 4340, 8620 or 6150, with a width of 600 mm or more

• (a) Flat-rolled products of other alloy steel, in coils, not further worked than cold-rolled (cold-reduced), of grade SAE J2340 490XF, with a width of 49.193 inches, 52.470 inches or 56.720 inches, with a thickness of at least 0.022 inch;

• (b) Flat-rolled products of other alloy steel, in coils, cold-rolled, of a width of 600 mm or more, dual phase, uncoated

• (a) Flat-rolled coils, sheets and plates of carbon steel, cold-rolled (cold-reduced), of grade JIS G3135 SPFC 590, of a width of 600 mm or more, of a thickness of at least 1.52 mm but not exceeding 1.68 mm;

• (b) Flat-rolled coils, sheets and plates of alloy steel, cold-rolled (cold-reduced), of grade SAE J2340 550Y, with a width of 600 mm or more, of a thickness of at least 1.19 mm but not exceeding 1.30 mm

• (a) Flat-rolled products of other alloy steel, in coils, sheets and plates, not further worked than cold-rolled (cold-reduced), of grade 8620, of specification SAE J404, with a width of less than 600 mm, of a thickness of at least 4.95 mm but not exceeding 5.06 mm, annealed;

• (b) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade J403 1050 SA, of a thickness of at least 3.41 mm but not exceeding 3.49 mm, annealed, of a width of:

  • (i) at least 83.80 mm but not exceeding 84.05 mm,

  • (ii) at least 99.75 mm but not exceeding 100.00 mm, or

  • (iii) at least 153.80 mm but not exceeding 154.22 mm;

• (c) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade J403 1050 CR SA, annealed, of a thickness of at least 3.00 mm but not exceeding 3.10 mm, with a width of:

  • (i) at least 33.80 mm but not exceeding 34.05 mm,

  • (ii) at least 38.10 mm but not exceeding 38.35 mm, or

  • (iii) at least 41.80 mm but not exceeding 42.05 mm;

• (d) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade SAE J403 1050 /55CR SA, of a thickness of at least 3.12 mm but not exceeding 3.22 mm, of a width of at least 47.75 mm but not exceeding 48.00 mm, annealed;

• (e) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced) of grade SAE J403 1050 SA, of a thickness of at least 2.95 mm but not exceeding 3.05 mm, of a width of at least 139.50 mm but not exceeding 139.75 mm, annealed;

• (f) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade J404 4130 CR, of specification SAE, of a thickness of at least 2.95 mm but not exceeding 6.00 mm, with a width of at least 100.75 mm but not exceeding 186.50 mm, annealed;

• (g) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade SAE J404 4130, of a thickness of at least 4.92 mm but not exceeding 5.00 mm, of a width of at least 97.75 mm but not exceeding 98.00 mm, annealed;

• (h) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade J404 4130, of a thickness of at least 2.90 mm but not exceeding 3.02 mm, annealed of a width of at least:

  • (i) at least 75.75 mm but not exceeding 97.00 mm, or

  • (ii) at least 245.75 mm but not exceeding 246.00 mm;

• (i) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade SAE J403 1050 SA, of a thickness of at least 3.93 mm but not exceeding 4.07 mm, of a width of at least 149.50 mm but not exceeding 149.75 mm, annealed;

• (j) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade J403 6150 SA, of a thickness of at least 3.45 mm but not exceeding 3.55 mm, of a width of at least 103.49 mm but not exceeding 103.74 mm, annealed;

• (k) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade SAE J404 4130, of a thickness of at least 4.92 mm but not exceeding 5.08 mm, of a width of at least 97.75 mm but not exceeding 98.00 mm, annealed;

• (l) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold reduced), of grade SAE J404 4130, of a thickness of at least 6.23 mm but not exceeding 6.43 mm, of a width of at least 137.75 mm but not exceeding 138.00 mm, annealed;

• (m) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold reduced), of grade SAE J404 4130, of a thickness of at least 6.9 mm but not exceeding 7.1 mm, of a width of at least 96.75 mm but not exceeding 97.00 mm, annealed;

• (n) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade ASTM A109 C1020, of a thickness of at least 1.9 mm but not exceeding 2.0 mm, of a width of at least 33.800 mm but not exceeding 34.025 mm;

• (o) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade SAE J403 1008 CR, of a thickness of at least 1.90 mm but not exceeding 1.98 mm, of a width of at least 201.75 mm but not exceeding 202.00 mm, annealed;

• (p) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade J403 1050 SA, of a thickness of at least 3.41 mm but not exceeding 3.49 mm, of a width of at least 83.80 mm but not exceeding 84.05 mm, annealed;

• (q) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold reduced), of grade J403 1050 SA, of a thickness of at least 3.41 mm but not exceeding 3.49 mm, of a width of at least 99.75 mm but not exceeding 100.00 mm, annealed;

• (r) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade ASTM A506 4130, of a thickness of at least 6.05 mm but not exceeding 6.25 mm, of a width of at least 83.8 mm but not exceeding 84.0 mm, annealed;

• (s) Flat-rolled products of other alloy steel, not further worked than cold-rolled (cold-reduced), of grade J403 1018 J403 SP, of a thickness of at least 3.91 mm but not exceeding 4.04 mm, of a width of at least 62.75 mm but not exceeding 63.00 mm, annealed;

• (t) Flat‐rolled products of other alloy steel, not further worked than cold‐rolled (cold reduced), of grade SAE J404 4130 CR, of a thickness of at least 2.45 mm but not exceeding 2.57 mm, of a width of at least 75.75 mm but not exceeding 76.00 mm, annealed

• (a) Flat-rolled coils, sheets and plates of carbon steel, with a width of less than 600 mm, of a thickness of at least 0.45 mm but not exceeding 4.00 mm, electrolytically plated or coated with zinc;

• (b) Flat-rolled coils, sheets and plates of aluminized alloy steel, of grade ASTM A463 CQ T-125, with a width of less than 600 mm, plated or coated with aluminum or aluminum alloys

• (a) Other bars and rods of other alloy steel, not further worked than hot-rolled, hot drawn or extruded, of grade 4130, of specification AISI 4130 or ASTM A29;

• (b) Other bars and rods of other alloy steel, not further worked than hot-rolled, hot drawn or extruded, of grade 4140, of specification ASTM A29, ASTM A322, ASTM A304, ASTM A108 or UNS.G41400;

• (c) Other bars and rods of other alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of grade 4150, of specification ASTM A29, ASTM A322, ASTM A304, ASTM A108, AISI 4150 or UNS G41500;

• (d) Other bars and rods of other alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of grade 9310, of specification ASTM A29, ASTM A322, ASTM A304, ASTM A108 or AISI 9310;

• (e) Other bars and rods of other alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of grade C1045, of a diameter of 1.5 inches, 2 inches, 3 inches or 3.5 inches, with a length of 20 feet;

• (f) Other bars and rods of other alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of grade C1045, of specification ASTM A108 SRA, with a diameter of 0.75 inches, with a length of 20 feet;

• (g) Other bars and rods of other alloy steel, not further worked than hot-rolled or hot-drawn, of grade 4140, of a diameter of 4.75 inches, of a length of 20 feet;

• (h) Other bars and rods, of special quality other alloy steel, not further worked than hot-rolled, hot-drawn or extruded, of grade 3125, 4130, 4130H, 4140, 4140AQ, 4140H, 4145, 4145H, 4340, 8620, 8620H, 8625, 8630, 8637, 8640 or 8735, of type AMS 6415 and AMS 2301, of a diameter of at least 1 inch but not exceeding 10 inches, vacuum degassed

• (a) Steel bar, of grade Aerospace M50 NIL VIM/VAR, Aerospace 52100 VIM/VAR, Aerospace 440C VAR or Aerospace 4340 VAR, of technical specifications AMS 6278, AMS 6491, AMS 6490, AMS 5618, AMS 6440, AMS 6444, AMS 6414 or AMS 6415, of specifications GE -B50TF347, PWA36140, EMS52526, B50TF346, P29TF48, CPW54, CPW378, MSRR6083, EMS83060, EMS52491, CAFM/L-01-119, DMD0119.20, EMS52494 ,PWA723, CPW52, EMS52493, EMS56627 or EMS83060, of a thickness of at least 0.5 inch but not exceeding 12 inches, with a length of 14 feet;

• (b) Bars and rods, of alloy steel other than stainless steel, maraging steel 250M & 300M, not further worked than cold-formed or cold-finished, of grade H13, modified 4340, or 4330, with a circular cross-sectional diameter of at least 1 inch but not exceeding 10 inches or with minimum dimensions of 10 inches height, 20 inches width and 16 inches length and maximum dimensions of 14 inches height, 28 inches width and 40 inches length for rectangular bars

• (a) Alloy steel bars and rods, cold formed or cold finish, of grade 4130, 4140, 4150, 4320, 4330, 4340, 52100, 8620 or 9310; vacuum degassed, annealed or quenched and tempered, or normalized and tempered, of specifications ASTM A29, ASTM A322, ASTM A304, ASTM A108, with a circular cross-sectional diameter not exceeding 8 inches or a rectangular cross-sectional thickness not exceeding 4 inches;

• (b) Round bars of uncoated alloy steel, of grade 4140, with an annealed cold finish, with a diameter of 1 inch, with a length of 144 inches;

• (c) Round bars of other alloy steel, not further worked than cold-formed or cold-finished, of grade 8620, of specification ASTM A108, of diameters of 0.6875 inch, 0.8750 inch or 1.0625 inches, including 0.030-inch undercut variants, of a length of at least 24 feet but not exceeding 36 feet

• (a) of grade 4130, other specification ASTM A20, with a circular cross-sectional diameter of less than 8 inches or a rectangular cross-sectional thickness of less than 4 inches;

• (b) of grade AISI 4130, 4140, or 4150, of specifications ASTM A29, ASTM 322, ASTM A304, or ASTM A108

• (a) Railroad clips and fasteners of steel, of specification AREMA Manual for Railway Engineering, Chapter 30 Ties and Fasteners, 1.7 Fasteners, type E-2055, with an outer diameter of 20 mm, with a length of 106 mm, with a width of 101.5 mm;

• (b) Railroad track and shimming spikes of carbon steel, of specification AREMA Manual for Railway Engineering, Chapter 5 Track, Section 2 Track Spikes, with a reinforced throat of 0.625 inches, with a width of 0.625 inches, and a length of 6 inches;

• (c) Track-circuit connector fasteners of carbon steel, with a length of 3 inches, with a width of 3 inches, with a height of 2 inches

• (a) In-line galvanized steel tubes, of high strength yield and customized tensile properties, with a thickness of at least 0.71 mm but not exceeding 4.57 mm, of specification ASTM A-1057;

• (b) Steel tubes, of low carbon, in coils, of specifications SAE J526, GMW17334, GMW3059, and GM124M, with a wall thickness of 0.70 mm, 0.79 mm or 0.89 mm, with an outer diameter of 9.52 mm, 12.70 mm, 15.88 mm or 19.05 mm, with a zinc–aluminum coating and an epoxy coating

• (a) Tubes of carbon steel, drawn over mandrel, of grade 1026, of specifications ASTM A513, ASTM A106 or ASTM A519;

• (b) Welded circular hollow structural sections, of iron or non-alloy steel, of grade 350W or A500C, of specification ASTM A53 or CSA G40.21, with a wall thickness of 4.8 mm, with an outer diameter of 60.3 mm, with a length of at least 2 m but not exceeding 6 m, uncoated

• (a) Tubes of carbon steel, drawn over mandrel, of grade 1026, of specifications ASTM A513, ASTM A106 or ASTM A519;

• (b) Steel tubes, drawn over mandrel, of specification ASTM A513, of grade 4130, of an outside diameter of 1.25 inches with a wall thickness of 0.250 inch or of an outside diameter of 3.0 inches with a wall thickness of 0.312 inch;

• (c) Steel tubes, drawn over mandrel, of grade 4130, of specification A513, with the following dimensions:

  • (i) 1.375 inches of diameter by 0.188 inch of wall thickness,

  • (ii) 1.625 inches of diameter by 0.25 inch of wall thickness,

  • (iii) 1.76 inches of diameter by 0.193 inch of wall thickness,

  • (iv) 2.0 inches of diameter by 0.188 inch of wall thickness,

  • (v) 2.0 inches of diameter by 0.25 inch of wall thickness,

  • (vi) 2.125 inches of diameter by 0.188 of wall thickness,

  • (vii) 2.25 inches of diameter by 0.188 inch of wall thickness,

  • (viii) 2.25 inches of diameter by 0.25 inch of wall thickness,

  • (ix) 2.375 inches of diameter by 0.2 inch of wall thickness,

  • (x) 2.625 inches of diameter by 0.25 inch of wall thickness,

  • (xi) 2.75 inches of diameter by 0.187 inch of wall thickness,

  • (xii) 3 inches of diameter by 0.25 inch of wall thickness,

  • (xiii) 3 inches of diameter by 0.285 inch of wall thickness,

  • (xiv) 3.25 inches of diameter by 0.375 inch of wall thickness,

  • (xv) 3.375 inches of diameter by 0.281 inch of wall thickness,

  • (xvi) 3.625 inches of diameter by 0.281 inch of wall thickness,

  • (xvii) 3.875 inches of diameter by 0.313 inch of wall thickness;

• (d) Tubes of low-carbon steel, in coils, of a specification SAE J526, with a wall thickness of 1.25 mm or 0.89 mm, with an outer diameter of 9.52 mm or 12.70 mm, with a zinc–aluminum coating and an epoxy coating

• (a) Other tubes, pipes and hollow profiles of iron or steel, welded, of circular cross-section, of iron or non-alloy steel, that have all of the following characteristics:

  • Grade: 1008, 1010, 1015 or 1020
  • Yield/tensile strength: 40 000 psi yield / 45 000 psi tensile, 45 000 psi yield / 48 000 psi tensile or 50 000 psi yield / 55 000 psi tensile
  • Specification: ASTM A500 or A513
  • Diameter: 0.5 to 5 inches
  • Coating: in-line galvanizing process utilizing a triple layer of protection (first, a 99.99% pure SHG zinc coating is applied to the surface, followed by a conversion coating and a clear organic topcoat that seals the surface and produces a smooth, shiny finished product)

• (b) Steel tubes, honed, of specification ASTM 513 Type 5, of an outside diameter of at least 1.875 inches but not exceeding 2.375 inches and an inside diameter of at least 1.500 inches but not exceeding 2.003 inches, with a minimum yield strength of 75 ksi;

• (c) Steel tubes, drawn over mandrel, of specification ASTM 513 Type 5, of an outside diameter of at least 2.375 inches but not exceeding 2.625 inches and an inside diameter of at least 1.984 inches but not exceeding 2.241, with a minimum yield strength of 75 ksi

• (a) Tubes, of stainless steel, welded, of circular cross-section, of grade 304/304L or 316/316L, of specification ASTM A270, with an outside diameter not exceeding 25.3 mm, with a wall thickness of less than 1.65 mm;

• (b) Tube assemblies, of stainless steel, incorporating bends, of grade 304L, of specification ASTM 269, with a wall thickness of 1.24 mm, with an outside diameter of 12.70 mm, and including at least one end of:

  • (i) brazed blocks of grade 304SS and specification ASTM A314, or

  • (ii) 0.75 inch-16 Unified National Fine (UNF) fittings, of grade EN1A low-carbon mild steel, of specification BS 970, with Zn/Ni plating of the standard ASTM B841

• (a) Other tubes, pipes and hollow profiles of iron or steel, welded, of square or rectangular cross-section, that have all of the following characteristics:

  • Grade: 1008, 1010, 1015 or 1020
  • Yield/tensile strength: 40 000 psi yield / 45 000 psi tensile, 45 000 psi yield / 48 000 psi tensile or 50 000 psi yield / 55 000 psi tensile
  • Specification: ASTM A500 or A513
  • Thickness: 0.625 to 4.000 inches (12 and 14 gauge)
  • Coating: in-line galvanizing process utilizing a triple layer of protection (first, a 99.99% pure SHG zinc coating is applied to the surface, followed by a conversion coating and a clear organic topcoat that seals the surface and produces a smooth, shiny finished product);

• (b) Other tubes, pipes and hollow profiles of iron or steel, welded, of square cross-section, that have all of the following characteristics:

  • Grade: 50 or better
  • Specification: ASTM A1011
  • Dimensions: 1.5 inches × 1.5 inches, 1.75 inches × 1.75 inches, 2.00 inches × 2.00 inches, 2.25 inches × 2.25 inches or 2.5 inches × 2.5 inches
  • Coating: galvanizing that meets ASTM A653;

• (c) Hollow structural sections, of iron or non-alloy steel, of grade 350W or A500C, of specification ASTM A53 or CSA G40.21, with a width of 63.5 mm, with a wall thickness of 3.18 mm, 4.78 mm or 6.35 mm, with a height of 63.5 mm, with a length of at least 2 m but not exceeding 6 m, uncoated;

• (d) Hollow structural sections, of iron or non-alloy steel, of grade 350W or A500C, of specification ASTM A53 or CSA G40.21, with a width of 76.2 mm, with a wall thickness of 4.78 mm, with a height of 76.2 mm, with a length of at least 2 m and 6 m, uncoated

Other tubes, pipes and hollow profiles, welded, of square or rectangular cross-section, that have all of the following characteristics:

• (a) Adapters for crossing gates, of steel, safety sensitive, with an assembled length of 32 inches, with an assembled width of 12 inches, with an assembled height of 7 inches;

• (b) Glare screen systems, of 25-gauge steel sheet of grades AISI 1008 or 1010, hot-dip galvanized to ASTM A653 with a G90 coating and powder-coated, supplied with 0.75-inch attachment hardware, concrete expansion anchors, and splice plates of 4140/42 steel with a thickness of 0.375 inch, with all hardware galvanized

• (a) Turnbuckle stud assemblies for cable-barrier systems, of steel, including threaded stud and nut, with a diameter of 1 inch, with a length of 7.87 inches, galvanized;

• (b) Cable spacers for cable-barrier systems, of steel, with a length of 0.15 m, galvanized;

• (c) Sleeve covers for cable-restraint system posts, of steel, with a width of 0.15 m, with a length of 0.2 m, hot-dip galvanized;

• (d) Dust covers for cable-restraint system posts, of steel, with a diameter of 180 mm, with a depth of 50 mm, galvanized;

• (e) Cable-barrier posts, of carbon steel, with a nominal height of 5.7 feet, with a length of 1.52 m, 10-gauge, galvanized;

• (f) Short posts for cable-barrier systems, of carbon steel with a length of 1.2 m, galvanized;

• (g) Post straps for cable-barrier systems, of steel, with a thickness of 6 mm, galvanized;

• (h) Post caps for cable-barrier systems, of steel, stamped, with a nominal height of 7.7 feet, with a width of 0.15 m, with a length of 0.15 m, hot-dip galvanized;

• (i) Washers, of carbon steel, with an inner diameter of 0.31 inch, with a zinc coating;

• (j) Washers, of hardened steel, of specification ASTM F436, with a diameter of 0.75 inch;

• (k) Hex nuts, of steel, of specification ASTM A194 2H, with a diameter of 0.75 inch;

• (l) Hex bolts, of steel, of specification ASTM A307, with a diameter of 0.31 inch, with a length of 1.75 inches;

• (m) Structural hex bolts, of steel, of a standard ASTM A325, with a diameter of 0.75 inch, with a length of 4.50 inches;

• (n) Post straps, of steel, with a thickness of 6 mm, with a length of 0.2 m, galvanized;

• (o) Hook bolts, of steel, with threaded section and formed hook end, with a diameter of 0.31 inch, with a length of 1.75 inches, for use with cable-barrier post assemblies;

• (p) Guardrail offset blocks or king blocks, of high-density polyethylene (HDPE), with a thickness of 4 inches, with a height of 7.5 inches, with a length of 14 inches;

• (q) Cable lock bolts, of steel, with a locking head for cable retention, with a diameter of 0.31 inch, for use in cable-barrier assemblies;

• (r) Lower posts for cable restraint system, of galvanized steel, with a length of 84 inches, for use in roadside barrier systems;

• (s) Post caps, of steel, stamped, galvanized, with a width of 150 mm, with a length of 150 mm;

• (t) Washers, of hardened steel, of specification ASTM F436, with a diameter of 1 inch;

• (u) Retroflective panels, of steel, with a width of 5 inches, with a length of 24 inches, galvanized or coated;

• (v) Cable stud assemblies, of steel, with a diameter of 25 mm, machined threads;

• (w) Terminal posts, of steel, for Test Level (TL-4) barrier systems, with a length of 71.62 inches, galvanized;

• (x) Driven sleeves, of steel, with a wall thickness of 0.19 inch and with a length of 30.75 inches, galvanized finish;

• (y) Base angles for cable anchor, of steel, with a thickness of 12 mm, with a width of 150 mm, with a length of 150 mm, galvanized finish;

• (z) Cable-restraint post brackets, of steel, with a thickness of 6 mm;

• (z.1) Line posts for a cable-control terminal of steel, galvanized;

• (z.2) Cable-restraint posts, of steel, galvanized, with a length of 0.61 m, supplied as an upper release-post assembly;

• (z.3) End terminals for roadside guardrail systems, of steel, meeting MASH Test Level 3 performance criteria, consisting of posts, release hardware and anchorage components;

• (z.4) Hex nuts, of carbon steel, of a standard ASTM A563, with a diameter of 0.31 inch;

• (z.5) Hex nuts, of steel, of a standard ASTM A194 2H, with a diameter of 1 inch;

• (z.6) Insulated metal panels, consisting of two profiled steel facings bonded to a rigid polyisocyanurate foam core, with a width of 40 inches, with a thickness of 3.0 inches or 4.5 inches, of a length of at least 96 inches but not exceeding 374 inches, with a polyvinylidene fluoride (PVDF) coating on the exterior facing and a polyester coating on the interior facing;

• (z.7) Insulated structural panels, consisting of a mineral-wool core bonded to steel facings of 22-gauge, 24-gauge or 26-gauge thickness, with a width of 42 inches or 43 inches, of a length of at least 8 feet but not exceeding 48 feet, with a thickness of 3 inches or of at least 4 inches but not exceeding 8 inches

• (a) Welded metal fasteners, “Weld Studs”, cold forged or hot forged, threaded or unthreaded, headed or unheaded, tapped, with or without a collar, flanged and un-flanged, with diameter of at least 2 mm but not exceeding 32 mm;

• (b) Insulation fasteners and weld pins for HVAC ductwork and insulation installation

• (a) Armour bolts, of carbon or alloy steel, forged, hardened and tempered, with oval heads, oval collars (anti-rotation), UNC-2A threads, with a nominal diameter of at least 1.5 inches but not exceeding 2.0 inches, with a length under head of at least 7 inches but not exceeding 45 inches;

• (b) Threaded hex bolts, of stainless steel, of grade 316L, of a nominal diameter of 0.375 inches or 0.500 inch, of a length of 3.25 inch, 3.50 inches or 5.50 inches, with thread pitches of 16 or 13 threads per inch

• (a) Double-ended stud, of standard M8, with thread pitch of 1.25 mm and length of 37 mm, with external 6-lobe drive and 17.5 mm header point, with acid treatment and zinc or nickel coating;

• (b) Double ended stud, of standard M8, with a thread pitch of 1.25 mm and length of 25 mm, pan head serrated neck, of grade 10.9, zinc coating;

• (c) Double ended stud, of standard M6, with a thread pitch of 1.00 mm, of grade 10.9, with zinc coating;

• (d) Projection weld stud of standard M8, with a length of 30 mm, with zinc coating;

• (e) Round-interior studs, of standard M6, with a diameter of 18.75 mm, with a rod diameter of 0.3050 inch, plain coating;

• (f) Studs, of M6 standards, with a 23.75 mm head diameter, with a 1.5 mm thread pitch, with a 25 mm length, with a rod diameter of 0.3450 inch

• (g) Studs, of M6 standard, of 18.97 mm head diameter of the stud, with a thread pitch of 1.0 mm, with a length of 21 mm, with a rod diameter of 0.3050 inch;

• (h) Studs, of M6 standard, with 18.97 mm head diameter, with a 1.0 mm thread pitch, with a length of 20 mm length, with a rod diameter of 0.3050 inch

• (a) Bolts, flange head, self-tapping, of standard M10, with a thread pitch of 1.5 mm and a length of 30 mm, meeting GM6202M, with a thread-forming surface treatment;

• (b) Socket bolts, of standard M12, with a thread pitch of 1.75 mm and a length of 120 mm, of grade 8.8, with a corrosion-protective surface treatment, meeting automotive specifications;

• (c) Clinch pins, of steel grades SAE 10B21 or 10B22, of 6 mm diameter and 12.5 mm length, with zinc-plated coating for corrosion protection;

• (d) Bolts, hex flange, of standard M12, with a thread pitch of 1.75 mm and a length of 80.0 mm, of property class 10, with a corrosion-protective aluminum-organic surface coating;

• (e) Bolts, hex flange, of standard M12, with a length of 120 mm, of property class 10, with a corrosion-protective aluminum-organic surface coating

• (a) Hex nuts, of projection weld type, of standard M12, with a thread pitch of 1.25 mm, of grade 8 steel, with a bare surface and rust-inhibitor treatment;

• (b) Weld studs, of standard M6, with a thread pitch of 1.0mm, with a length of 16mm, of specification GMW25M (8.8) with a maximum carbon content of 0.26% and plain coating;

• (c) Studs, projection-weld, of standard M6, with a thread pitch of 1.0 mm, with a length of 25 mm, of specifications GMW25M;

• (d) Studs, projection weld type, of standard M6, of 1.0 mm thread pitch and 20 mm length, of property class 8.8;

• (e) Weld hex nuts, of standard M8, of 1.25 mm thread pitch, with head diameter of 22.5 mm, of 0.59 inch wire rod;

• (f) Threaded anchor nuts, of iron or steel, with a nominal diameter of 35 mm or 46 mm

• (a) Semi-autogenous grinding balls for mills, of steel containing 0.6% carbon, forged or stamped, with a diameter of 5 inches;

• (b) Forged or stamped steel grinding balls for mills, heat-treated, with a diameter of 3.5 inches

• (a) Steel hose clamps, single-band type, of grade 51CrV4, of specification SAE J404 6150M, of a thickness of at least 0.98 mm but not exceeding 1.08 mm, with a width of 15 mm, of a nominal size of 16 mm or 17 mm, of a closed diameter of 14.9 mm or 15.6 mm, of a full-open diameter of 17.5 mm or 18.5 mm, of a clamping force of 145 mm or 195 mm, with a chrome-free zinc-based epoxy coating;

• (b) Steel hose clamps with plastic removal clips, double-band type, of grade 51CrV4, of specification SAE J404 6150M for the band and of grade PA55 Type 6.6 , of a thickness of at least 0.98 mm but not exceeding 1.08 mm, with a width of 10 mm or 15 mm, of a nominal size of 16 mm or 17 mm, with a chrome-free zinc-based epoxy coating;

• (c) Steel spools, cold-rolled, of grade CQ1008 or CQ1010, fabricated with an eight-rib design, with flange diameters of 8 inches and 10 inches, with a drum diameter of 4.5 inches, with a traverse length of 6 inches, with an arbor size of 1.25 inches, painted;

• (d) Forged steel saw-blade blanks, with coating;

• (e) Breakaway couplings, machined from round ETD 4142 alloy-steel bar stock, hot-wrought to a specification ASTM A29/A29M-20, galvanized after machining to ASTM A153 and packaged with hardware galvanized to ASTM A653;

• (f) Breakaway couplings, of alloy steel, hot-wrought, of grade ETD 4142, galvanized to ASTM A513, with hardware;

• (g) Female anchoring systems for concrete, comprising a pinch-welded assembly of a stainless steel washer of grade 304, a steel coil of grade 1080 with a diameter of 0.4375 inch, a stainless steel internally threaded ferrule of grade 304 with a 0.625-inch-11 thread, and a carbon steel rod of grade 1045 with a diameter of 0.4375 inch;

• (h) Steel hinge assemblies, with hinge plates of grade 4140/42, galvanized to ASTM A153, and supplied with galvanized attachment hardware

• (a) Welded metal fasteners, “weld studs”, of mild or stainless steel; cold forged, hot forged, threaded or unthreaded, headed or un-headed, tapped, with or without a collar, flanged or un-flanged diameters of at least 2 mm but not exceeding 32 mm;

• (b) Step assemblies, of steel, with standard drive operation and power switch kit, with a step extension of 25.5 inches, with a load capacity of 300 pounds;

• (c) Stainless-steel cylindrical shell, of 10-gauge SA240-304 stainless-steel plate, with an outer diameter of 38 inches, with a length of 82 inches, with an 2B interior finish and a 180-grit exterior finish, welded on two sides, wrapped in polyvinyl chloride on two sides;

• (d) Steel anchor heads for post-tensioning, of specification EN ISO 683-1 or EN ISO 683-2, for strand sizes 19-0.6, 27-0.6 and 31-0.6, for intermediate grouting, comprising galvanized multi-port anchors with two 0.75-inch National Pipe Taper (NPT) ports and associated anchoring and grouting components;

• (e) Grout caps for use with strand sizes 19-0.6, 27-0.6, 31-0.6, 1.375 inches and 1.750 inches, of specification EN 10130, including stainless steel pipe fittings and ball valves;

• (f) Three-piece wedges of iron or steel, of specification EN 10277, with a nominal diameter of 0.62 inch;

• (g) Couplings, of type ASTM C1277 or CSA B602, with a neoprene sleeve and stainless steel shield and clamps, of a diameter of at least 1.5 inches but not exceeding 15.0 inches

• (a) Aluminum coils, with a thickness of 0.0106 to 0.018 inch, with a width of 1.1650 to 10.7086 inches, with a polyester or epoxy laminate, of alloys 5352 and 5042;

• (b) Aluminum sheets coated with an electron beam cure, with a thickness of 0.045 inch, in sheets of 49 inches × 97 inches;

• (c) Aluminum plates, sheets and strip, of alloy AA1350 of a thickness exceeding 0.2 mm but less than 7 mm;

• (d) Aluminum plates, sheets and strip, rectangular (including square), of aluminum alloy 1000 series, 3000 series, 5000 series, or 6000 series, with a thickness exceeding 0.2 mm;

• (e) Aluminum sheets, rectangular (including square), of an aluminum alloy 2024-T3, of a standard ASTM B209, of a thickness of at least 1.803 mm but not exceeding 2.286 mm, with a width of 2 121 mm, with a length of 2 629 mm;

• (f) Aluminum sheets, rectangular (including square), of grade AA3105, of a standard ASTM B209, of a width of at least 2.5 inches but not exceeding 24.0 inches, of a thickness of 0.381 mm but not exceeding 0.508 mm, with a polyester paint coating

• (a) Aluminum plates, sheets and strip, rectangular (including square), of 3104 alloy, of a thickness of at least 0.254 mm but not exceeding 0.259 mm, of a width of at least 1 454.0 mm but not exceeding 1 692.4 mm, uncoated;

• (b) Aluminum sheet, rectangular (including square), of a thickness of at least 0.032 inch but not exceeding 0.040 inch, painted;

• (c) Aluminum plates, sheets and strip, rectangular (including square), of 3104 alloy, of a thickness of at least 0.254 mm but not exceeding 0.259 mm, with a 1735.2 mm width, uncoated;

• (d) Aluminum sheets, rectangular (including square), of grade 3105-H24, 3003-H14 or 5005-H34, of a standard ASTM B209, of a thickness of 0.032 inch or 0.050 inch, with a width of 48 inches, with a length of 96 or 120 inches, painted or anodized

• (a) Aluminum tubes or pipes of aluminum alloys, cylindrical shape, seamless, of grade AA6101 or AA6063, of specification ASTMB241 or ASTMB317, with a wall thickness of at least 0.109 inch but not exceeding 0.500 inch, of an outer diameter not exceeding 10 inches, of a length of at least 5 feet but not exceeding 40 feet;

• (b) Aluminum tubes, in coils, of grade H14, of specifications AA3003-H14 and ASTM B483, with a wall thickness of 1.24 mm, with an outer diameter of 9.52 mm;

• (c) Aluminum tubes, in coils, of grade H13, of specifications AA3003-H13 and ASTM B483M-95, with a wall thickness of 1.24 mm, with an outer diameter of 12.7 mm;

• (d) Aluminum tubes, in coils, of grade H13, of specifications AA3003-H13, ASTM B483M-95 and MS 8580-A9, with a wall thickness of 1.24 mm, with an outer diameter of 15.88 mm;

• (e) Aluminum tubes, in coils, of grade H14, of specifications AA3003-H14 and ASTM B483, with a wall thickness of 1.24 mm, with an outer diameter of 12.7 mm;

• (f) Aluminum tubes, in coils, of grade H14, of specifications AA3003-H14 and ASTM B483, with a wall thickness of 1.24 mm, with an outer diameter of 15.88 mm;

• (g) Aluminum tubes, in coils, of grade H12, meeting specifications AA3103-H12 and ASTM B483M-03, with a wall thickness of 1 mm, with an outer diameter of 12 mm;

• (h) Aluminum tubes, in coils, of grade H12, of specifications AA3003-H12 and ASTM B483M-95M, with a wall thickness of 1 mm, with an outer diameter of 10 mm;

• (i) Aluminum tubes, in coils, of grade H14, of specifications AA3003-H14 and ASTM B483, with a wall thickness of 1.65 mm, with an outer diameter of 19.05 mm;

• (j) Aluminum tubes, in coils, of grade H14, of specifications AA3003-H14 and ASTM B483, with a wall thickness of 1.65 mm, with an outer diameter of 15.88 mm;

• (k) Aluminum tubes, in coils, of grade H12, of specifications AA3003-H12 and ASTM B483M-95M, with a wall thickness of 0.9 mm, with an outer diameter of 9.52 mm;

• (l) Aluminum tubes, in coils, of grade H12, of specifications AA3003-H12, ASTM B483M-95M and MS 8580-A9, with a wall thickness of 1.25 mm, with an outer diameter of 15 mm;

• (m) Aluminum tubes and pipes, of grade 6061, 2011, 7075, 3003 and 5052

• (a) Self locking vane and rail system in 2 or 4 inch configurations used to redirect airflow in HVAC ductwork;

• (b) Adjustable elbows for round HVAC ductwork;

• (c) Flexible duct connector to reduce vibration transmission in HVAC ductwork;

• (d) HVAC ductwork components allowing for branching off main HVAC ductwork;

• (e) Straight flange and cleat system including integrated mastic for joining HVAC ductwork;

• (f) Rolled or stamped angle rings for connecting round HVAC ductwork;

• (g) Aluminum mechanical adapters, of hardcoat-anodized alloy, with 5-inch or 6-inch coupling configuration, including polymer bearing ring, with NFPA 1964;

• (h) Aluminum 30-degree elbows, hardcoat-anodized, with a 5-inch rigid Storz coupling and a 3-inch female NH swivel rocker lug coupling, compliant with NFPA 1964 Standard, with powder coat finish inside and out;

• (i) Aluminum, blind cap Storz couplings, heat-treated, with a diameter of 5 inches, supplied with a suction gasket and an 18-inch lanyard with 0.25-inch eyelet for attachment

• (a) Aluminium structures designed to cover reservoirs, tanks and bulk material storage facilities;

• (b) Aluminum composite sheets, of a thickness of at least 3 mm but not exceeding 4 mm, consisting of a non-aluminum core bonded to two painted aluminum skins with a width of 0.02 inch

• (a) Aluminum food can easy open ends;

• (b) Steel metal closures, inside surface includes a polyester coating, of technical specifications ASTM T2, T3, T4, T5, DR7.5 or DR8, in nominal diameters of 38 mm, 40 mm, 48 mm, 58 mm, 63 mm, 70 mm or 82 mm;

• (c) Steel food can ends and lids, including those made from tinplate (steel coated with a thin layer of tin) or tin-free steel (electrolytic chromium-coated steel, ECCS), lined or unlined with a food-safe polymer coating;

• (d) Aluminum can ends, of a nominal diameter of at least 2.324 inches but not exceeding 2.340 inches, coated