Interpretation

Marginal note:Definitions

• 1 (1) The definitions in this subsection apply in these Regulations.

  acid reserve

  acid reserve means the quantity of an alkali, expressed in grams of sodium hydroxide, that is required to bring 100 mL of a liquid acidic product, or 100 g of an acidic product in the form of a solid, paste or gel, to a pH of 4.00 ± 0.05. (réserve acide)

  Act

  Act[Repealed, SOR/2011-24, s. 1]

  alkali reserve

  alkali reserve means the quantity of an alkali, expressed in grams of sodium hydroxide, that is neutralized when 100 mL of a liquid basic product, or 100 g of a basic product in the form of a solid, paste or gel, is brought to a pH of 10.00 ± 0.05 by the addition of hydrochloric acid or its equivalent. (réserve alcaline)

  aspiration

  aspiration means the entry of a liquid or solid chemical product directly through the oral or nasal cavity, or indirectly from vomiting, into the trachea or lower respiratory system. (aspiration)

  chemical product

  chemical product means a product used by a consumer that has the properties of one or more of the following:

  • (a) a toxic product;

  • (b) a corrosive product;

  • (c) a flammable product; or

  • (d) a quick skin-bonding adhesive.

  It does not include any of the following:

  • (e) a product described in any of paragraphs (a) to (d) if it is not possible for a user to be exposed to the product or to any of its hazardous ingredients during reasonably foreseeable use;

  • (f) a portable petroleum container that conforms with CSA B306 or CSA B376;

  • (g) a lighter;

  • (h) a fire extinguisher that conforms with ULC-S503, ULC-S504, ULC-S507 or ULC-S512; or

  • (i) a container of fuel, such as gasoline, ethanol or propane, if the container is permanently attached to an internal combustion engine, a gas turbine or an appliance that uses the fuel. (produit chimique)

  complex mixture

  complex mixture means a combination of chemicals that has a generic name that is not a trade name and is

  • (a) a substance of natural origin;

  • (b) a fraction obtained by a physical separation process from a substance of a natural origin; or

  • (c) a chemical modification of a substance of natural origin or of a fraction obtained by a physical separation process from a substance of natural origin. (mélange complexe)

  container

  container means

  • (a) a Category 5 pressurized container that is or is likely to be used by a consumer, including an empty container, as described in Part 5;

  • (b) an empty container that is destined for use by a consumer to store or dispense a chemical product; or

  • (c) any other container that is or is likely to be used by a consumer to store or dispense a chemical product. (contenant)

  corrosive product

  corrosive product means a chemical product that

  • (a) is capable of inducing necrosis or ulceration of epithelial tissue;

  • (b) is capable of causing an erythema or edema of the skin, corneal or iris damage or conjunctival swelling or redness; or

  • (c) is identified in Part 2 as a Category 2 corrosive product. (produit corrosif)

  display surface

  display surface means the portion of the surface area of a container on which the information required by these Regulations can be displayed. It does not include the surface area of the bottom, of any seam or of any concave or convex surface near the top or the bottom of a container. (aire d’affichage)

  dust

  dust means solid airborne particles that are mechanically generated. (poussière)

  first aid statement

  first aid statement means

  • (a) a list of the hazardous ingredients in the chemical product; and

  • (b) a statement of the first aid treatment to be administered to anyone who has come into contact with a chemical product, such as through ingestion, absorption or inhalation, or information that may be helpful to someone who is assisting that individual. (énoncé de premiers soins)

  flame projection

  flame projection means the flame resulting from the ignition of a chemical product discharged from a spray container when tested in accordance with the procedure set out in Schedule 1. (projection de la flamme)

  flammable product

  flammable product means a chemical product that is capable of

  • (a) spontaneous combustion;

  • (b) becoming flammable when in contact with air; or

  • (c) having a flash point below 60°C or a flame projection greater than 15 cm or exhibiting a flashback. (produit inflammable)

  flashback

  flashback means the part of a flame projection that extends from the point of ignition back towards the spray container when a chemical product is tested in accordance with the procedure set out in Schedule 1. (retour de flamme)

  flash point

  flash point means the minimum temperature at which a substance gives off a vapour in sufficient concentration to ignite under test conditions. (point d’éclair)

  fume

  fume means solid particles in the air that are generated by condensation from the vapour of a solid material. (fumée)

  fumes

  fumes, in the context of the information that must be displayed on a container, means a vapour or a fume or both that may be given off by a chemical product under normal conditions of use or storage. (émanations)

  good scientific practices

  good scientific practices means

  • (a) for the development of test data, conditions and procedures similar to those set out in the OECD Test Guidelines;

  • (b) for laboratory practices, practices similar to those set out in the OECD Principles of Good Laboratory Practice; and

  • (c) for human experience data, a peer-reviewed study of clinical cases. (bonnes pratiques scientifiques)

  hazard category

  hazard category means a category into which a chemical product or container is classified, in particular:

  • (a) Category 1, toxic products set out in Part 1;

  • (b) Category 2, corrosive products set out in Part 2;

  • (c) Category 3, flammable products set out in Part 3;

  • (d) Category 4, quick skin-bonding adhesives set out in Part 4; and

  • (e) Category 5, pressurized containers set out in Part 5. (catégorie de danger)

  hazard symbol

  hazard symbol means a pictograph and its frame as set out in Schedule 2. (pictogramme de danger)

  hazardous ingredient

  hazardous ingredient means

  • (a) a pure chemical product;

  • (b) an ingredient present in a chemical product in a concentration of 1% or more that is taken into consideration when classifying the product and that

    • (i) is a chemical product,

    • (ii) the supplier believes on reasonable grounds may be harmful to humans,

    • (iii) has toxicological properties that are not known to the supplier, or

    • (iv) derives from a reaction between precursor constituents and the hazards associated with the chemical product are not known to the supplier; or

  • (c) a complex mixture present in a chemical product in a concentration of 1% or more that is taken into consideration when classifying the product and that

    • (i) is a chemical product,

    • (ii) the supplier believes on reasonable grounds may be harmful to humans, or

    • (iii) has toxicological properties that are not known to the supplier. (ingrédient dangereux)

  human experience data

  human experience data means data, collected in accordance with good scientific practices, that demonstrates that injury to or poisoning of a human has or has not resulted from

  • (a) exposure to a chemical product; or

  • (b) the reasonably foreseeable use of a chemical product or container by a consumer, including, in particular, the consumption of the product by a child. (données de l’expérience humaine)

  LC₅₀

  LC₅₀ means the concentration of a substance in air that, when administered by means of inhalation over a specified length of time in an animal assay, is expected to cause the death of at least 50% of a defined population of animals. (CL₅₀)

  LD₅₀

  LD₅₀ means the single dose of a substance that, when administered by a defined route in an animal assay, is expected to cause the death of at least 50% of a defined population of animals. (DL₅₀)

  main display panel

  main display panel means the part of the display surface that is displayed or visible under normal conditions of sale to the consumer. It includes

  • (a) in the case of a rectangular container, the largest side of the display surface;

  • (b) in the case of a cylindrical container, the larger of

    • (i) the area of the top, or

    • (ii) 40% of the area obtained by multiplying the circumference of the container by the height of the display surface;

  • (c) in the case of a bag, the largest side of the bag; and

  • (d) in the case of any other container, the largest surface of the container that is not less than 40% of the display surface. (aire d’affichage principale)

  manufacturer

  manufacturer includes a packager and a labeller. (fabricant)

  mist

  mist means droplets of liquid suspended in air that are produced by the condensation of a vapourized liquid or by the dispersion of a liquid by a spray container. (brouillard)

  mixture

  mixture means a combination of two or more products, materials or substances that do not undergo a chemical change as a result of their interaction. (mélange)

  National Standard

  National Standard means a standard recognized by the National Standards System of the Standards Council of Canada. (norme nationale)

  normal atmospheric pressure

  normal atmospheric pressure means an absolute pressure of 101.324 kPa at 20°C. (pression atmosphérique normale)

  official languages

  official languages means the English and French languages. (langues officielles)

  person responsible

  person responsible[Repealed, SOR/2016-170, s. 1]

  quick skin-bonding adhesive

  quick skin-bonding adhesive means a Category 4 adhesive set out in Part 4 that has properties similar to an alkyl cyanoacrylate adhesive and that is capable of bonding skin with skin instantly or nearly instantly. (adhésif qui colle rapidement la peau)

  responsible person

  responsible person means

  • (a) the manufacturer, in the case of a chemical product or container that is manufactured in Canada; and

  • (b) the importer, in the case of a chemical product or container that is imported. (responsable)

  single-use container

  single-use container means a non-reclosable container whose contents are to be used in their entirety immediately after the container is opened. (contenant à usage unique)

  spray container

  spray container means a container that permits the dispersal of its contents in the form of a mist and includes a pressurized container and a pump-spray container. (contenant pulvérisateur)

  sub-category

  sub-category means one of the following classifications within a hazard category in which a chemical product may be classified, in particular:

  • (a) in the case of a Category 1 toxic product, “very toxic”, “toxic” and “harmful”;

  • (b) in the case of a Category 2 corrosive product, “very corrosive”, “corrosive” and “irritant”; and

  • (c) in the case of a Category 3 flammable product, “spontaneously combustible”, “very flammable”, “flammable” and “combustible”. (sous-catégorie)

  toxic product

  toxic product means a chemical product that

  • (a) is capable of causing a lethal effect on a human;

  • (b) is capable of causing a serious and irreversible but non-lethal effect on a human, such as a depressed level of consciousness, muscular weakness or paralysis, acute renal or hepatic failure, arrhythmia, hypotension, dyspnea, respiratory depression, pulmonary edema or optic neuritis; or

  • (c) is identified in Part 1 as a Category 1 toxic product. (produit toxique)

  vapour

  vapour means the gaseous form of a substance that is found in a solid or liquid state at normal atmospheric pressure. (vapeur)

• Marginal note:Table of standards and tests

  (2) A standard or test set out in column 2 of the table to this subsection is referenced in these Regulations, in the provision set out in column 3, by means of the short form set out in column 1.

  	Column 1	Column 2	Column 3
  ItemFootnote for TABLE TO SUBSECTION 1(2) Standards and Tests Referenced in These Regulations*	Short form	Standard or test	Provision of Regulations
  1 (1)	ASTM D 56	ASTM Standard D 56-05(2010), entitled Standard Test Method for Flash Point by Tag Closed Cup Tester, approved May 1, 2005, published May 2005	50(a); 51
  2 (2)	ASTM D 93	ASTM Standard D 93-02a, entitled Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester, approved December 10, 2002, published March 2003	50(b)
  3 (3)	ASTM D 323	ASTM Standard D 323-06, entitled Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method), approved August 1, 2006	58(1)(a)
  4 (4)	ASTM D 1293	ASTM Standard D 1293-99, entitled Standard Test Methods for pH of Water, approved December 10, 1999	44(1)
  5 (5)	ASTM D 3828	ASTM Standard D 3828-05, entitled Standard Test Methods for Flash Point by Small Scale Closed Cup Tester, approved May 1, 2005, published May 2005	50(a)
  6 (6)	16 CFR 1700.20	U.S. Code of Federal Regulations, Title 16: Commercial Practices, section 1700.20, entitled “Testing procedure for special packaging”, revised January 1, 2008	9(b)
  7 (7)	CSA B306	CSA Standard B306-M1977 (R2018), entitled Portable Fuel Tanks for Marine Use, as amended April 1988	1(1) chemical product
  8 (8)	CSA B339	CAN/CSA Standard B339-02, entitled Cylinders, Spheres, and Tubes for the Transportation of Dangerous Goods, as amended February 2005	58(2)
  9 (9)	CSA B376	CSA Standard B376-M1980 (R2019), entitled Portable Containers for Gasoline and Other Petroleum Fuels, published July 1980 in the English version and June 1986 in the French version	1(1) chemical product
  10 (10)	CSA Z76.1	CSA Standard Z76.1-06(R2016), entitled Reclosable child-resistant packages, published March 2006 in the English version and July 2006 in the French version	9(b)
  11 (17)	Draize Test	Draize Test, described in “Methods for the Study of Irritation and Toxicity of Substances Applied Topically to the Skin and Mucous Membranes”, Volume 82, The Journal of Pharmacology and Experimental Therapeutics, 1944, pages 377 to 390	43(2)(a)
  12 (11)	ISO 8317	ISO Standard 8317:2003, entitled Child-resistant packaging — Requirements and testing procedures for reclosable packages, Second edition, dated April 15, 2003	9(b)
  13 (12)	OECD No. 404	OECD Guideline for the Testing of Chemicals No. 404, entitled Acute Dermal Irritation/Corrosion, adopted April 24, 2002	43(2)(b)
  14 (16)	OECD No. 405	OECD Guideline for the Testing of Chemicals No. 405, entitled Acute Eye Irritation/Corrosion, adopted April 24, 2002	43(2)(c)
  15 (13)	OECD Principles of Good Laboratory Practice	Number 1 of the OECD Series on Principles of Good Laboratory Practice and Compliance Monitoring, ENV/MC/CHEM(98)17, dated January 21, 1998 in the English version and March 6, 1998 in the French version	1(1) good scientific practices; 44(2)(a)
  16 (14)	OECD Test Guidelines	Annex 1, entitled OECD Test Guidelines, of the Decision of the Council Concerning the Mutual Acceptance of Data in the Assessment of Chemicals, C(81)30 (Final), adopted by the Council of the OECD on May 12, 1981	1(1) good scientific practices; 6(1)(b) and (c); 35(1)(a) and (b)
  17 (15)	Test L.2	“Test L.2: Sustained combustibility test” set out in section 32.5.2 of the Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria, Fifth Revised Edition, 2009, United Nations (UN)	48(2)(b)
  18 (18)	ULC‑S503	CAN/ULC Standard S503-05-R2018, Fourth Edition, entitled Carbon-Dioxide Fire Extinguishers, published February 28, 2005	1(1) chemical product
  19 (19)	ULC‑S504	CAN/ULC Standard S504-12-R2018, Third Edition, entitled Dry Chemical Fire Extinguishers, published August 14, 2002	1(1) chemical product
  20 (20)	ULC‑S507	CAN/ULC Standard S507-05-R2018, Fourth Edition, entitled Water Fire Extinguishers, published February 28, 2005	1(1) chemical product
  21 (21)	ULC-S512	CAN/ULC-S512-M87(R2007), entitled Standard for Halogenated Agent Hand and Wheeled Fire Extinguishers, as amended April 1999	1(1) chemical product
  Legend:
  ASTM	American Society for Testing and Materials
  CSA	Canadian Standards Association
  ISO	International Organization for Standardization
  OECD	Organisation for Economic Cooperation and Development
  ULC	Underwriters’ Laboratories of Canada

  • Return to footnote ^*The numbers in parentheses that follow the item numbers indicate the corresponding item number in the French version.

• Marginal note:Interpretation of “should”

  (3) Where the word “should” is used in a standard or test referenced in these Regulations it is to be read as imperative, unless the context requires otherwise.

• Marginal note:Units of measure

  (4) The symbol set out in column 1 of the table to this subsection represents the unit of measure set out in column 2.

  	Column 1	Column 2
  Item	Symbol	Unit of measure
  1	°C	degree Celsius
  2	cm	centimetre
  3	cm2	square centimetre
  4	g	gram
  5	g/m2	grams per square metre
  6	kg	kilogram
  7	kPa	kilopascal
  8	L	litre
  9	mg/kg	milligrams per kilogram
  10	mg/L	milligrams per litre
  11	mL/m3	millilitres per cubic metre
  12	mm	millimetre
  13	mm2/s	square millimetres per second
  14	N	newton

• Marginal note:Concentration

  (5) In these Regulations, unless otherwise specified, when a concentration of a substance is expressed as a percentage, the percentage represents the ratio of the weight of the substance to the weight of the chemical product.

Non-application

Marginal note:Vaping products

2 These Regulations do not apply to vaping products as defined in section 2 of the Tobacco and Vaping Products Act.

General Provisions

Marginal note:Exceptions — importation to bring into compliance or to export

• 3 (1) A person may import a chemical product or container that does not comply with a requirement of these Regulations for the purpose of

  • (a) bringing the product or container into compliance with the requirement;

  • (b) reselling the product or container to a manufacturer in Canada who will bring it into compliance with the requirement; or

  • (c) exporting the product or container to another country.

• Marginal note:Credible evidence

  (2) A person who imports a chemical product or a container for a purpose described in subsection (1) must, on the request of an inspector, provide credible evidence to the inspector that it is being brought into compliance with these Regulations or is being exported, as the case may be.

• (3) [Repealed, SOR/2009-165, s. 3]

Requirements

Hazard Category, Container and Information

Marginal note:Determination by responsible person

• 4 (1) The responsible person, using one or more of the applicable properties, data sources or test procedures set out in section 6 or Parts 1 to 5, must determine

  • (a) the hazard categories of the chemical product or container and, if applicable, its appropriate sub-categories;

  • (b) the type of container that is required; and

  • (c) the information that is required to be displayed on the container.

• Marginal note:Multiple hazard categories

  (2) If a chemical product and its container fall into more than one hazard category, its container must display the information that is required for every applicable hazard category.

• Marginal note:Multiple sub-categories

  (3) Subject to subsection (4), if a chemical product falls into more than one sub-category within a hazard category, the responsible person must classify the product in the sub-category that represents the greatest hazard within each applicable hazard category.

• Marginal note:Multiple sub-categories — flammable products

  (4) If a chemical product falls into both the sub-category “spontaneously combustible” and another sub-category in the hazard category “Category 3, flammable product”, it must be classified in both sub-categories.

• Marginal note:Multiple routes of exposure

  (5) The container of a chemical product to which an individual may be exposed by more than one route of exposure must display the required information for each route of exposure.

Marginal note:Documents

5 The responsible person must

• (a) prepare and maintain all documents relating to the determinations required under subsection 4(1) and keep the documents for a period of at least three years after the day on which the chemical product or container is manufactured in Canada or the day on which it is imported; and

• (b) within 15 days after receipt of a request from an inspector, provide the documents to the inspector.

Data Sources

Marginal note:Precedence of data sources

• 6 (1) The responsible person must determine the hazards arising from the reasonably foreseeable use of the chemical product or container from one or more of the following data sources in the following order of precedence:

  • (a) human experience data pertaining to the product or container;

  • (b) data, set out in peer-reviewed, scientific literature, from tests conducted using the product in accordance with the OECD Test Guidelines;

  • (c) if tests using the product have not been conducted in accordance with the OECD Test Guidelines,

    • (i) the peer-reviewed results of tests conducted with the product in accordance with

      • (A) these Regulations,

      • (B) a National Standard or an international standard recognized by the Standards Council of Canada, or

      • (C) a generally accepted procedure that accorded with good scientific practices at the time the tests were conducted,

    • (ii) the peer-reviewed results of tests conducted with a chemical product that has properties similar to those of the product under examination, in accordance with

      • (A) OECD Test Guidelines,

      • (B) a National Standard or an international standard recognized by the Standards Council of Canada, or

      • (C) a generally accepted procedure that accorded with good scientific practices at the time the tests were conducted, or

    • (iii) other current, peer-reviewed information about the product;

  • (d) if the hazards associated with the product cannot be estimated from information referred to in paragraphs (a) to (c), data with respect to the hazards associated with

    • (i) the hazardous ingredients, or

    • (ii) a chemical product that has properties similar to those of the product under examination; or

  • (e) the results of tests conducted by the responsible person in accordance with a test methodology that conforms with good scientific practices.

• Marginal note:Differing data sources

  (2) In the case of differing data sources,

  • (a) an original literature source must be used in preference to literature that refers to the original study; and

  • (b) a source that reports test results that conform with good scientific practices and that disclose the greatest hazard must be used.

Containers

Marginal note:Leakage test

7 A container of a liquid chemical product must pass the leakage test described in Schedule 3 or an equivalent test.

Marginal note:Single-use containers

8 A single-use container must display, in the manner set out in sections 17 to 20, subsections 24(1) and (3) and sections 25 and 26, the following primary hazard statement:

“USE ENTIRE CONTENTS ON OPENING.”

“UTILISER LA TOTALITÉ DU CONTENU APRÈS OUVERTURE.”

Child-resistant Containers

Marginal note:Applicable standard

9 A child-resistant container must

• (a) be constructed so that it can be opened only by operating, puncturing or removing one of its functional and necessary parts using a tool that is not supplied with the container; or

• (b) meet the child test protocol requirements of one of CSA-Z76.1, ISO 8317 or 16 CFR 1700.20 or a standard that is at least equivalent.

Marginal note:Maintain characteristics

• 10 (1) A child-resistant container must, when in contact with a chemical product, maintain its child-resistant characteristics throughout the useful life of the product.

• Marginal note:Evaluation

  (2) The responsible person, using good scientific practices, must evaluate

  • (a) the compatibility of the chemical product with its child-resistant container, to determine that the chemical or physical properties of the product will not compromise or interfere with the proper functioning of the container; and

  • (b) the physical wear and stress factors and the force required for opening and closing the container, to determine that the proper functioning of the container will be maintained for the number of openings and closings reasonably foreseeable for the size and contents of the container.

Marginal note:Directions to open and close

• 11 (1) Subject to subsection (2), a child-resistant container that meets the requirements of paragraph 9(b) must display directions explaining how to open and, if applicable, to close the container

  • (a) on the closure, using either or both of

    • (i) words that comply with sections 17 to 19, or

    • (ii) a diagram or self-explanatory symbol that complies with paragraph 17(b) and section 18; or

  • (b) on the container, located after the positive instructions for the chemical product and set out in a manner that complies with requirements for a positive instruction in sections 17 to 19, subsection 24(1) and sections 25, 29 and 30.

• Marginal note:Exception

  (2) The directions for opening and, if applicable, closing a child-resistant container may be set out on the closure in only one official language if they are repeated on the container in the other official language in the manner set out in paragraph (1)(b).

Marginal note:Documents

• 12 (1) The responsible person must prepare and maintain documents containing the following information and must keep those documents for a period of at least three years after the day on which the child-resistant container is manufactured in Canada or the day on which it is imported:

  • (a) for a container that comes into direct contact with the chemical product, the specifications critical to the child-resistant characteristics of the container, which specifications must include

    • (i) the physical measurements within which the container retains its child-resistant characteristics,

    • (ii) if applicable, the torque that must be applied to open or close the container, and

    • (iii) the compatibility of the container and its closure system with the chemical product that is to be put into it; and

  • (b) the test results that demonstrate that the container and its closure system comply with the requirements of a standard set out in paragraph 9(b).

• Marginal note:Inspector’s request

  (2) The responsible person for a chemical product that is required by these Regulations to be packaged in a child-resistant container must provide an inspector with any of the documents that the inspector requests within 15 days after the day on which the request is received.

Marginal note:Child-resistant, single-use containers

13 A child-resistant, single-use container must display, in the manner set out in sections 17 to 20, subsections 24(1) and (3) and sections 25 and 26, the following primary hazard statement:

“USE ENTIRE CONTENTS ON OPENING. THIS CONTAINER IS NOT CHILD-RESISTANT ONCE OPENED.”

“UTILISER LA TOTALITÉ DU CONTENU APRÈS OUVERTURE. UNE FOIS OUVERT, LE CONTENANT N’EST PLUS UN CONTENANT PROTÈGE-ENFANTS.”

Marginal note:Exception — large container

14 The requirements for child-resistant containers set out in sections 9 to 13 do not apply to a container with a capacity greater than 5 L, other than the container for a chemical product that is classified in one of the following:

• (a) the hazard category “Category 4, quick skin-bonding adhesives”; or

• (b) the sub-category “very corrosive”.

• (c) [Repealed, SOR/2011-24, s. 3]

Required Information

Marginal note:Containers and packaging

• 15 (1) Subject to section 16, the information required by these Regulations must be displayed in the manner set out in these Regulations

  • (a) on each container that is displayed to the consumer, other than in an advertisement; and

  • (b) on any packaging of a container that is displayed to the consumer, including a display card to which a container may be fixed.

• Marginal note:Adaptation

  (1.1) For the purpose of the application of paragraph (1)(b), the requirements for the display of information on a container apply to the display of information on the container’s package having regard to the size of the package.

• Marginal note:Additional information

  (2) Information in addition to that required by these Regulations may be displayed on a container if it does not disclaim or contradict the required information.

Marginal note:Exemption — packaging

• 16 (1) Packaging is exempt from the requirements of paragraph 15(1)(b) if the packaging

  • (a) is transparent and

    • (i) the required information displayed on the container is legible through the packaging, and

    • (ii) the transparent packaging does not obscure any of the required information on the container; or

  • (b) is not transparent and

    • (i) encloses

      • (A) a container and a product that is not subject to these Regulations, or

      • (B) two or more containers that have different information requirements, and

    • (ii) displays the following signal word and primary hazard statement, or a statement to the same effect, in the manner set out in sections 17 to 20 and 23, subsections 24(1) and (3) and sections 25, 26 and 28:

      “CAUTION. CONTAINS PRODUCTS THAT MAY BE HARMFUL. READ WARNINGS ON EACH CONTAINER.”

      “ATTENTION. CONTIENT DES PRODUITS QUI PEUVENT ÊTRE NOCIFS. LIRE LES MISES EN GARDE SUR CHAQUE CONTENANT.”

• Marginal note:Exemption — packaging not customarily displayed

  (2) Packaging that is not customarily displayed to the consumer, such as a shipping carton, is exempt from the requirements of paragraph 15(1)(b).

Presentation of Information — Technical Specifications

Marginal note:Languages, legibility and durability

17 The information required by these Regulations to be displayed on a container must be

• (a) displayed in both official languages; and

• (b) clear and legible and remain so throughout the useful life of the chemical product, or in the case of a refillable container, throughout its useful life, under normal conditions of transportation, storage, sale and use.

Marginal note:Colour contrast

18 The colour contrast between the information and the background must be equivalent to at least a 70% screen of black on white.

Marginal note:Print — general rules

• 19 (1) If the information is set out in words, they must be printed in a standard sans serif type that

  • (a) is not compressed, expanded or decorative; and

  • (b) as illustrated in Schedule 4, has a large “x-Height” relative to the ascender or descender of the type.

• Marginal note:Measurement of height of type

  (2) The height of the type referred to in subsection (1) is determined by measuring an upper-case letter or a lower-case letter that has an ascender or descender, such as “b” or “p”.

Marginal note:Print — upper-case letters

20 The following information must be printed

• (a) in upper-case letters

  • (i) the signal word,

  • (ii) the primary hazard statement, and

  • (iii) the specific hazard statement; and

• (b) in bold-faced, upper-case letters, the titles “FIRST AID TREATMENT” and “PREMIERS SOINS”.

Marginal note:Hazard symbol — reproduction

21 The hazard symbol must be an exact reproduction of the applicable symbol depicted in Schedule 2, except with respect to size and colour.

Marginal note:Hazard symbol — minimum diameter

22 The hazard symbol must, when the main display panel has the area set out in column 1 of the table to this section, have a diameter at least as large as that set out in column 2.

• Return to footnote ^*Alternatively, this diameter may be calculated by multiplying the square root of the area in cm² of the main display panel by 1.95.

Marginal note:Signal word — height

23 The height of the signal word must be at least one quarter of the minimum diameter of a hazard symbol determined in accordance with section 22.

Marginal note:Other information — height and body size

• 24 (1) Subject to subsection (3), when the main display panel has an area set out in column 1 of the table to this subsection, the following information must be in type that is at least the height set out in column 2 and at least the body size set out in column 3:

  • (a) the primary hazard statement;

  • (b) the specific hazard statement;

  • (c) the negative and positive instructions; and

  • (d) the titles “FIRST AID TREATMENT” and “PREMIERS SOINS”.

    	Column 1	Column 2	Column 3
    Item	Area of the main display panel	Minimum height of type	Minimum body size of type
    1	less than 100 cm2	2 mm	6 point
    2	100 cm2 or more but less than 330 cm2	3 mm	8 point
    3	330 cm2 or more	4 mm	12 point

• Marginal note:First aid statement — height and body size

  (2) Subject to subsection (3), the first aid statement, except for the titles “FIRST AID TREATMENT” and “PREMIERS SOINS”, must be in type that has a minimum height of 2 mm and a minimum body size of 6 points.

• Marginal note:Exception — quick skin-bonding adhesive

  (3) In the case of a quick skin-bonding adhesive referred to in Part 4, when the main display panel of the container has an area set out in column 1 of the table to this subsection, the primary hazard statement, the titles “FIRST AID TREATMENT” and “PREMIERS SOINS” and the first aid statement must be in type that is at least the height set out in column 2 and at least the body size set out in column 3.

  	Column 1	Column 2	Column 3
  Item	Area of the main display panel	Minimum height of type	Minimum body size of type
  1	less than 10 cm2	1.5 mm	4.5 point
  2	10 cm2 or more but less than 35 cm2	2 mm	6 point

Location and Order — General Rule

Marginal note:Location and order

• 25 (1) The information required by these Regulations must be displayed on the container at the following locations and in the following order:

  • (a) on the main display panel,

    • (i) a hazard symbol,

    • (ii) the signal word “EXTREME DANGER”, “DANGER” or “CAUTION”, as the case may be, and

    • (iii) the primary hazard statement; and

  • (b) on any part of the display surface,

    • (i) the specific hazard statement,

    • (ii) negative instructions,

    • (iii) positive instructions, and

    • (iv) the first aid statement.

• Marginal note:Exemption — small container

  (2) Despite subsection (1) and subject to Part 4, if the main display panel of a container has an area of

  • (a) less than 35 cm², only the hazard symbol and the signal word need be displayed; or

  • (b) 35 cm² or more but less than 70 cm² and more than one hazard symbol is required, the required negative and positive instructions, other than the positive instructions referred to in subsection 11(2), may be omitted.

Location on Main Display Panel

Marginal note:Location of hazard symbol, signal word and primary hazard statement

• 26 (1) The information referred to in paragraph 25(1)(a) must be located as follows:

  • (a) below the common name or brand name of the chemical product;

  • (b) centred parallel to and near the base of the main display panel; and

  • (c) subject to subsection (3), immediately below one another.

• Marginal note:Base of collapsible tube

  (2) For the purpose of paragraph (1)(b), the base of the main display panel of a collapsible tube is the end from which the chemical product is discharged.

• Marginal note:Exception — short, wide containers

  (3) If the main display panel has a height that is less than 10 cm and a width that is at least twice the height, the signal word may be located immediately beside the hazard symbol instead of below it.

Marginal note:Multiple hazard symbols

27 If more than one hazard symbol is required, the symbols must be grouped immediately beside each other in a row parallel to the base of the container.

Marginal note:Precedence among signal words

28 If these Regulations require that more than one signal word be displayed on a container, only the signal word that discloses the greatest hazard must be displayed on the container.

Location of Other Hazard Information

Marginal note:Location of specific hazard statement, instructions and first aid statement

29 The information referred to in paragraph 25(1)(b) must be

• (a) left justified; and

• (b) enclosed within a border that demarcates the information from other information displayed on the display surface.

Marginal note:Border

30 The border referred to in paragraph 29(b)

• (a) may include a series of dots or hatched lines, a difference in colour or shading of the background or some other graphic device;

• (b) must be different from any other border on the label; and

• (c) must comply with paragraph 17(b) and section 18.

Marginal note:First aid statement — order of information

31 The first aid statement must set out the following information in the following order:

• (a) the title “FIRST AID TREATMENT” and “PREMIERS SOINS”;

• (b) the words “Contains” and “Contient”;

• (c) a list of the hazardous ingredients in the chemical product, in the manner set out in section 32, in descending order of their proportions; and

• (d) the required statements of first aid treatment.

Marginal note:Hazardous ingredients

32 A hazardous ingredient referred to in paragraph 31(c) must be identified

• (a) by its chemical identity; or

• (b) in the case of a complex mixture, by its generic name.

PART 1Toxic Products

Classification of Toxic Products

Marginal note:Data sources

33 The responsible person for a toxic product must determine the appropriate sub-category for the product from one or more of the following data sources in the following order of precedence:

• (a) human experience data pertaining to the toxic product;

• (b) in the case of a toxic product that contains a substance of special concern, the table to subsection 34(1);

• (c) in the case of a toxic product that poses a risk of exposure through an oral, a dermal or an inhalation route, the LD₅₀ or LC₅₀ or both, as the case may be, of the product as determined in accordance with the applicable table to subsections 34(2) to (4) and the data sources and formulas set out in sections 35 to 37; or

• (d) in the case of a toxic product that poses an aspiration hazard, the properties set out in subsection 34(5).

Marginal note:Sub-categories — substance of special concern

• 34 (1) A chemical product that contains a substance of special concern set out in column 1 of the table to this subsection in a concentration set out in column 2 must, when introduced through a route of exposure set out in column 3, be classified in the sub-category set out in column 4.

  	Column 1	Column 2	Column 3	Column 4
  Item	Substance of special concernFootnote for TABLE TO SUBSECTION 34(1) Sub-Categories — Substance of Special Concern*	Concentration	Route of exposure	Sub-category
  1	Carbon tetrachloride	Any concentration	Oral, inhalation or aspiration	Very Toxic
  2	Diethylene glycol	5% or more	Oral	Harmful
  3	Ethyl acetate	5% or more	Oral	Harmful
  4	Ethylene glycol	(a) 5% or more but less than 10%	Oral	Harmful
  		(b) 10% or more	Oral	Toxic
  5	Hydrocyanic acid or its salts	Any concentration	Oral, dermal or inhalation	Very Toxic
  6	Methyl alcohol	1% or more and a total quantity of 5 mL or more	Oral or inhalation	Toxic
  7	Nitrobenzene	5 mg/kg or more	Oral, dermal or inhalation	Very Toxic
  8	1,1,2,2-tetrachloroethane	Any concentration	Oral, dermal or inhalation	Very Toxic
  9	1,2-dichloroethane	(a) 5% or more but less than 10%	Oral or inhalation	Harmful
  		(b) 10% or more	Oral or inhalation	Toxic
  10	1,1,1-trichloroethane	5% or more	Oral or inhalation	Harmful

  • Return to footnote ^*These substances are of special concern because standard animal tests may not reflect the actual hazard they pose to humans.

• Marginal note:Sub-categories — oral exposure

  (2) A chemical product that poses a risk to a consumer through an oral route and has an LD₅₀ set out in column 1 of the table to this subsection must be classified in the sub-category set out in column 2.

  	Column 1	Column 2
  Item	LD50	Sub-category
  1	not more than 50 mg/kg	Very Toxic
  2	more than 50 mg/kg but not more than 500 mg/kg	Toxic
  3	more than 500 mg/kg but not more than 2 000 mg/kg	Harmful

• Marginal note:Sub-categories — dermal exposure

  (3) A chemical product that poses a risk to a consumer through a dermal route and has an LD₅₀ set out in column 1 of the table to this subsection must be classified in the sub-category set out in column 2.

  	Column 1	Column 2
  Item	LD50	Sub-category
  1	not more than 200 mg/kg	Very Toxic
  2	more than 200 mg/kg but not more than 1 000 mg/kg	Toxic
  3	more than 1 000 mg/kg but not more than 2 000 mg/kg	Harmful

• Marginal note:Sub-categories — inhalation exposure

  (4) A chemical product that poses a risk to a consumer through inhalation, is in the state set out in column 1 of the table to this subsection and has a 4-hour LC₅₀ set out in column 2 must be classified in the sub-category set out in column 3.

  	Column 1	Column 2	Column 3
  Item	State of the chemical product	4-hour LC50	Sub-category
  1	Gas	(a) not more than 2 500 mL/m3	Very Toxic
  		(b) more than 2 500 mL/m3 but not more than 5 000 mL/m3	Harmful
  2	Vapour	(a) not more than 1 500 mL/m3	Very Toxic
  		(b) more than 1 500 mL/m3 but not more than 2 500 mL/m3	Toxic
  		(c) more than 2 500 mL/m3 but not more than 10 000 mL/m3	Harmful
  3	Dust, mist or fume	(a) not more than 0.5 mg/L	Very Toxic
  		(b) more than 0.5 mg/L but not more than 2.5 mg/L	Toxic
  		(c) more than 2.5 mg/L but not more than 5.0 mg/L	Harmful

• Marginal note:Sub-category — aspiration hazard

  (5) A chemical product must be classified in the sub-category “toxic” if it has a viscosity of 14 mm²/s or less at 40°C and 10% or more of the product is composed of hazardous ingredients that pose an aspiration hazard, including, in particular, any of the following substances:

  • (a) an n-primary alcohol with a composition of at least 3 carbon atoms but not more than 13;

  • (b) an isobutyl alcohol;

  • (c) a terpene alcohol;

  • (d) a ketone with a composition of at least 3 carbon atoms but not more than 13;

  • (e) a hydrocarbon with a composition of at least 3 carbon atoms but not more than 13; or

  • (f) a substance that has been determined to be an aspiration hazard based on its viscosity, surface tension and water solubility through the application of generally accepted standards of good scientific practices.

Determination of Toxicity

Marginal note:Data sources

• 35 (1) The responsible person for a toxic product must determine, from one or more of the following data sources in the following order of precedence, its toxicity or, in the case of a mixture that separates, the toxicity of each layer of the mixture:

  • (a) the LD₅₀ or LC₅₀ or both, as the case may be, of the product or of the layer as determined by the peer-reviewed results of acute toxicity tests using the product on animals, which tests were conducted in accordance with the OECD Test Guidelines for acute toxicity testing;

  • (b) if tests on animals using the product have not been conducted in accordance with the OECD Test Guidelines for acute toxicity testing, the LD₅₀ or LC₅₀ or both, as the case may be, of the product or of the layer as determined by

    • (i) peer-reviewed results of acute toxicity tests of the product or the layer, which tests were conducted on animals in accordance with

      • (A) a National Standard or an international standard recognized by the Standards Council of Canada, or

      • (B) a generally accepted procedure that conformed with good scientific practices at the time the tests were conducted,

    • (ii) if the product is a mixture that does not separate, section 36,

    • (iii) peer-reviewed results of tests of a chemical product or a substance that has similar properties to those of the product or of the layer under examination, which tests were conducted on animals in accordance with

      • (A) OECD Test Guidelines for acute toxicity testing,

      • (B) a National Standard or an international standard recognized by the Standards Council of Canada, or

      • (C) a generally accepted procedure that conformed with good scientific practices at the time the tests were conducted, or

    • (iv) other current, peer-reviewed information about the product or the layer; or

  • (c) the LD₅₀ or LC₅₀ or both, as the case may be, of the product or of the layer as determined by the results of tests conducted with the toxic product by the responsible person in accordance with a test methodology that conforms with good scientific practices.

• Marginal note:Differing data sources

  (2) In the case of differing data sources,

  • (a) an original literature source must be used in preference to a literature source that refers to the original study; and

  • (b) a source that reports test results that conform with good scientific practices and that disclose the greatest hazard must be used.

• Marginal note:Mixture that separates

  (3) In the case of a mixture that separates, the toxic product must be assigned the LD₅₀ or LC₅₀ or both, as the case may be, of the most toxic layer.

• Definition of mixture that separates

  (4) In this section, mixture that separates means a chemical product in a liquid or semi-liquid state that separates into two or more distinct layers if left standing undisturbed for a period of 30 days at 20^oC.

Marginal note:Additivity formulas — LD₅₀ or LC₅₀ of mixtures

• 36 (1) The LD₅₀ or LC₅₀ of a mixture may be determined from the LD₅₀ or LC₅₀ of its ingredients that are present in a concentration of 1% or more, using one of the following additivity formulas, as the case may be:

  • (a) for a solid or a liquid

    LD₅₀ = 1/[(P_a/LD_50a)+(P_b/LD_50b)+...+(P_n/LD_50n)]

    where

    LD₅₀

    represents the LD₅₀ of the mixture,

    LD_50a to LD_50n

    represent the LD₅₀ of each ingredient that is present in a concentration of 1% or more, and

    P_a to P_n

    represent the proportion by weight of each ingredient that is present in a concentration of 1% or more; or

  • (b) for a gas, vapour, dust, mist or fume

    LC₅₀ = 1/[(P_a/LC_50a)+(P_b/LC_50b)+...+(P_n/LC_50n)]

    where

    LC₅₀

    represents the LC₅₀ of the mixture,

    LC_50a to LC_50n

    represent the LC₅₀ of each ingredient that is present in a concentration of 1% or more, and

    P_a to P_n

    represent the proportion by weight of each ingredient that is present in a concentration of 1% or more.

• Marginal note:Complex mixture

  (2) For the purposes of the additivity formulas set out in subsection (1), “ingredient” includes a complex mixture.

• Marginal note:When LD₅₀ or LC₅₀ of ingredient is not known but can be estimated

  (3) When the LD₅₀ or LC₅₀ of one or more ingredients present in a chemical product in a concentration of 1% or more is not known, the responsible person may, in the additivity formulas set out in subsection (1), use an estimated LD₅₀ or LC₅₀ determined in accordance with good scientific practices.

• Marginal note:When LD₅₀ or LC₅₀ of ingredient is not known and cannot be estimated

  (4) When the LD₅₀ or LC₅₀ of one or more ingredients present in a chemical product is not known and cannot be estimated from information referred to in paragraph 35(1)(b) or (c), the responsible person, in the additivity formulas set out in subsection (1), must substitute for the LD₅₀ or LC₅₀ of the ingredient, the LD₅₀ or LC₅₀ of the most toxic known ingredient that is present in the product at a concentration of 1% or more.

Marginal note:Conversion to a 4-hour LC₅₀

37 An LC₅₀ obtained during a duration of exposure of other than four hours must be converted to an LC₅₀ equivalent to a duration of exposure of four hours by using one of the following formulas, as the case may be:

• (a) for a gas or vapour

  LC_{50 of 4 hours} = (LC_50y)(y^½/2)

  where

  LC_{50 of 4 hours}

  represents the LC₅₀ of the mixture for a duration of exposure of four hours,

  LC_50y

  represents the LC₅₀ of the mixture for a duration of exposure of y hours, and

  y

  represents the actual duration of exposure expressed in hours and must be no greater than 10 hours; or

• (b) for a dust, mist or fume

  LC_{50 of 4 hours} = (LC_50y)(y/4)

  where

  LC_{50 of 4 hours}

  represents the LC₅₀ of the mixture for a duration of exposure of four hours,

  LC_50y

  represents the LC₅₀ of the mixture for a duration of exposure of y hours, and

  y

  represents the actual duration of exposure expressed in hours and must be no greater than 10 hours.

Very Toxic Products

Marginal note:Prohibition

38 The manufacturing, importation, advertising or sale of a chemical product that is classified in the sub-category “very toxic” under section 33 is prohibited.

Required Information

Marginal note:Required information — sub-category “toxic”

• 39 (1) The container of a chemical product that is classified in the sub-category “toxic” under section 33 must display, for each type of information set out in column 1 of the table to this subsection, and for each applicable route of exposure set out in column 2, the information set out in columns 3 and 4, other than the instructions set out in italics.

  	Column 1	Column 2	Column 3	Column 4
  Item	Type of information	Applicable route of exposure	English information	French information
  1	Hazard symbol	All
  2	Signal word	All	DANGER	DANGER
  3	Primary hazard statement	All	POISON	POISON
  4	Specific hazard statement	(a) Oral or aspiration	CONTENTS HARMFUL	CONTENU NOCIF
  		(b) Dermal	CONTENTS HARMFUL	CONTENU NOCIF
  		(c) Inhalation	CONTENTS HARMFUL or, if only the vapour or fume poses a hazard: FUMES HARMFUL	CONTENU NOCIF or, if only the vapour or fume poses a hazard: ÉMANATIONS NOCIVES
  5	Negative instructions	(a) Oral or aspiration	Do not swallow.	Ne pas avaler.
  		(b) Oral and contains 1% or more methyl alcohol and a total quantity of 5 mL or more	May cause blindness if swallowed.	L’ingestion peut causer la cécité.
  		(c) Dermal	Do not get in eyes or on skin or clothing.	Éviter tout contact avec les yeux, la peau et les vêtements.
  		(d) Inhalation	Do not breathe fumes.	Ne pas respirer les émanations.
  6	Positive instructions	(a) All	Keep out of reach of children.	Tenir hors de la portée des enfants.
  		(b) Oral or aspiration	Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., a mask.].	Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., un masque.].
  		(c) Dermal	Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., rubber gloves, safety glasses.].	Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., des gants de caoutchouc, des lunettes de sécurité.].
  		(d) Inhalation	Use only in a well-ventilated area. Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., a mask, a respirator.].	N’utiliser que dans un endroit bien aéré. Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., un masque, un respirateur.].
  7	First aid statement	(a) All	FIRST AID TREATMENT Contains [name of hazardous ingredients in descending order of proportion]. If swallowed, call a Poison Control Centre or doctor immediately.	PREMIERS SOINS Contient [name of hazardous ingredients in descending order of proportion]. En cas d’ingestion, appeler immédiatement un centre antipoison ou un médecin.
  		(b) Oral or aspiration	When appropriate, [Insert instructions for administering first aid, e.g., Do not induce vomiting.].	When appropriate, [Insert instructions for administering first aid, e.g., Ne pas provoquer le vomissement.].
  		(c) Dermal	If in eyes or on skin, rinse well with water. If on clothes, remove clothes.	En cas de contact avec les yeux ou la peau, bien rincer avec de l’eau. En cas de contact avec les vêtements, enlever ceux-ci.
  		(d) Inhalation	If breathed in, move person into fresh air.	En cas d’inhalation, transporter à l’air frais la personne exposée.

• Marginal note:Required information — sub-category “harmful”

  (2) The container of a chemical product that is classified in the sub-category “harmful” under section 33 must display, for each type of information set out in column 1 of the table to this subsection, and for each applicable route of exposure set out in column 2, the information set out in columns 3 and 4, other than the instructions set out in italics.

  	Column 1	Column 2	Column 3	Column 4
  Item	Type of information	Applicable route of exposure	English information	French information
  1	Hazard symbol	All
  2	Signal word	All	CAUTION	ATTENTION
  3	Primary hazard statement	All	POISON	POISON
  4	Specific hazard statement	(a) Oral or aspiration	CONTENTS MAY BE HARMFUL	LE CONTENU PEUT ÊTRE NOCIF
  		(b) Dermal	CONTENTS MAY BE HARMFUL	LE CONTENU PEUT ÊTRE NOCIF
  		(c) Inhalation	CONTENTS MAY BE HARMFUL or, if only the vapour or fume poses a hazard: FUMES MAY BE HARMFUL	LE CONTENU PEUT ÊTRE NOCIF or, if only the vapour or fume poses a hazard: LES ÉMANATIONS PEUVENT ÊTRE NOCIVES
  5	Negative instructions	(a) Oral or aspiration	Do not swallow.	Ne pas avaler.
  		(b) Dermal	Do not get in eyes or on skin or clothing.	Éviter tout contact avec les yeux, la peau et les vêtements.
  		(c) Inhalation	Do not breathe fumes.	Ne pas respirer les émanations.
  6	Positive instructions	(a) All	Keep out of reach of children.	Tenir hors de la portée des enfants.
  		(b) Oral or aspiration	Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., a mask.].	Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., un masque.].
  		(c) Dermal	Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., rubber gloves, safety glasses.].	Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., des gants de caoutchouc, des lunettes de sécurité.].
  		(d) Inhalation	Use only in a well-ventilated area. Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., a mask, a respirator.].	N’utiliser que dans un endroit bien aéré. Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., un masque, un respirateur.].
  7	First aid statement	(a) All	FIRST AID TREATMENT Contains [name of hazardous ingredients in descending order of proportion]. If swallowed, call a Poison Control Centre or doctor immediately.	PREMIERS SOINS Contient [name of hazardous ingredients in descending order of proportion]. En cas d’ingestion, appeler immédiatement un centre antipoison ou un médecin.
  		(b) Oral or aspiration	When appropriate, [Insert instructions for administering first aid, e.g., Do not induce vomiting.].	When appropriate, [Insert instructions for administering first aid, e.g., Ne pas provoquer le vomissement.].
  		(c) Dermal	If in eyes or on skin, rinse well with water. If on clothes, remove clothes.	En cas de contact avec les yeux ou la peau, bien rincer avec de l’eau. En cas de contact avec les vêtements, enlever ceux-ci.
  		(d) Inhalation	If breathed in, move person into fresh air.	En cas d’inhalation, transporter à l’air frais la personne exposée.

• (3) [Repealed, SOR/2009-165, s. 12]

Child-resistant Containers

Marginal note:Sub-category “toxic”

• 40 (1) Subject to subsection (2) and section 14, a chemical product that is classified under section 33 in the sub-category “toxic” must be in a child-resistant container that complies with sections 9 to 13.

• Marginal note:Exceptions — spray container and single-drop dispenser

  (2) Subsection (1) does not apply to a chemical product classified under section 33 in the sub-category “toxic” that is in

  • (a) a spray container that cannot be opened and that disperses the product as a mist; or

  • (b) a container that

    • (i) dispenses only one drop of the product at a time, and

    • (ii) displays the following primary hazard statement in the manner set out in sections 17 to 20, subsections 24(1) and (3) and sections 25 and 26:

      “THIS CONTAINER IS NOT CHILD-RESISTANT. KEEP OUT OF REACH OF CHILDREN.”

      « CE CONTENANT N’EST PAS UN CONTENANT PROTÈGE-ENFANTS. TENIR HORS DE LA PORTÉE DES ENFANTS. »

PART 2Corrosive Products

Classification of Corrosive Products

Marginal note:Data sources

• 41 (1) The responsible person for a corrosive product must determine the appropriate sub-category for the product from one or more of the following data sources in the following order of precedence:

  • (a) subject to subsection (2), human experience data for the corrosive product;

  • (b) the table to subsection 42(1), in the case of a corrosive product that contains a substance of special concern;

  • (c) one or more of the following sources in the following order of precedence, in the case of a corrosive product that contains one or more acids or one or more bases:

    • (i) the data sources set out in paragraph 6(1)(b), (c) or (e), or

    • (ii) the pH and, if applicable, the acid reserve or the alkali reserve of the corrosive product as set out in the tables to subsections 42(2) and (3), determined using the test methods set out in section 44;

  • (d) the table to subsection 42(4), in the case of a corrosive product that contains a substance, other than an acid or a base, that is capable of inducing necrosis or ulceration of epithelial tissue at the site of application determined using the data sources set out in subsection 43(1); or

  • (e) subsection 42(5), in the case of a corrosive product that contains a substance, other than an acid or a base, that is capable, when tested using the appropriate test methods set out in subsection 43(2), of causing any of the following at the site of application:

    • (i) an erythema or edema of the skin graded at 2 or more,

    • (ii) corneal damage graded at 2 or more,

    • (iii) iris damage graded at 1 or more, or

    • (iv) conjunctival swelling or redness graded at 2.5 or more.

• Marginal note:Classification using human experience data

  (2) If the human experience data for a corrosive product demonstrates that the product is capable of causing an effect described in

  • (a) paragraph (1)(d), the product must be classified in the sub-category “corrosive”; or

  • (b) any of subparagraphs (1)(e)(i) to (iv), the product must be classified in the sub-category “irritant”.

Marginal note:Sub-categories — substance of special concern

• 42 (1) A chemical product that contains one or more of the substances of special concern set out in column 1 of the table to this subsection in a concentration set out in column 2 must be classified in the sub-category set out in column 3.

  	Column 1	Column 2	Column 3
  Item	Substance of special concern	Concentration	Sub-category
  1	Ethyl bromoacetate	any concentration	Very Corrosive
  2	Fluoride	0.5% or more of available fluoride ions	Very Corrosive

• Marginal note:Sub-categories — one or more acids

  (2) A chemical product that contains one or more acids, is in the state set out in column 1 of the table to this subsection and has the properties set out in column 2, as determined under section 44, must be classified in the sub-category set out in column 3.

  	Column 1	Column 2	Column 3
  Item	State	Properties	Sub-category
  1	Liquid	(a) a pH of not more than 1.0	Corrosive
  		(b) a pH of more than 1.0 but not more than 3.0, and an acid reserve of 5.0 or more	Corrosive
  		(c) a pH of more than 1.0 but not more than 3.0, and an acid reserve of 3.0 or more but less than 5.0	Irritant
  2	Solid, paste or gel	(a) a pH of not more than 1.0	Corrosive
  		(b) a pH of more than 1.0 but not more than 3.0, and an acid reserve of 10.0 or more	Corrosive
  		(c) a pH of more than 1.0 but not more than 3.0, and an acid reserve of 5.0 or more but less than 10.0	Irritant

• Marginal note:Sub-categories — one or more bases

  (3) A chemical product that contains one or more bases, is in the state set out in column 1 of the table to this subsection and has the properties set out in column 2, as determined under section 44, must be classified in the sub-category set out in column 3.

  	Column 1	Column 2	Column 3
  Item	State	Properties	Sub-category
  1	Liquid	(a) a pH of 13.0 or more	Corrosive
  		(b) a pH of less than 13.0 but not less than 11.0, and an alkali reserve of 5.0 or more	Corrosive
  		(c) a pH of less than 13.0 but not less than 12.0, and an alkali reserve of less than 5.0	Irritant
  		(d) a pH of less than 12.0 but not less than 11.0, and an alkali reserve of less than 5.0 but not less than 3.0	Irritant
  2	Solid, paste or gel	(a) a pH of 13.0 or more	Corrosive
  		(b) a pH of less than 13.0 but not less than 11.0, and an alkali reserve of 10.0 or more	Corrosive
  		(c) a pH of less than 13.0 but not less than 12.0, and an alkali reserve of less than 10.0	Irritant
  		(d) a pH of less than 12.0 but not less than 11.0, and an alkali reserve of less than 10.0 but not less than 5.0	Irritant

• Marginal note:Sub-categories — substances causing necrosis or ulceration

  (4) A chemical product that contains substances described in paragraph 41(1)(d) that are capable of causing necrosis or ulceration, in a total concentration set out in column 1 of the table to this subsection, must be classified in the sub-category set out in column 2.

  	Column 1	Column 2
  Item	Total concentration of the substances	Sub-category
  1	5% or more	Corrosive
  2	1% or more but less than 5%	Irritant

• Marginal note:Sub-category — substances causing other effects

  (5) A chemical product that contains substances that are capable of causing an effect described in paragraph 41(1)(e) in a total concentration of 5% or more must be classified in the sub-category “irritant”.

Test Methods

Marginal note:Determination — necrosis and ulceration

• 43 (1) The capability of a substance in a corrosive product to induce necrosis or ulceration of epithelial tissue at the site of application must be determined from an applicable data source set out in paragraphs 6(1)(a) to (c) or (e).

• Marginal note:Determination — other effects

  (2) The capability of a substance in a corrosive product to cause an erythema or edema of the skin, corneal or iris damage or conjunctive swelling or redness at the site of application, to the grade specified in paragraph 41(1)(e), must be determined from the applicable data source set out in paragraphs 6(1)(a) to (c) or (e), including

  • (a) the Draize Test;

  • (b) in the case of an erythema or an edema, OECD No. 404; and

  • (c) in the case of corneal or iris damage or conjunctive swelling or redness, OECD No. 405.

Marginal note:Determination of the pH

• 44 (1) The responsible person for a corrosive product must determine the pH of the product by using good scientific practices that are in accordance with a procedure similar to that described in ASTM D 1293, from

  • (a) in the case of a product in the form of a liquid, the product as it is dispensed from its container; and

  • (b) in the case of a product in the form of a solid, paste or gel, or in a form otherwise unsuitable for direct measurement of the pH, a 10% aqueous solution of the product.

• Marginal note:Determination of acid reserve or alkali reserve

  (2) The responsible person for a corrosive product must determine, where applicable, the acid reserve or the alkali reserve of the product by

  • (a) titrating, in accordance with the OECD Principles of Good Laboratory Practice,

    • (i) in the case of a product in the form of a liquid, a suitable aliquot of the product as it is dispensed from its container, and

    • (ii) in the case of a product in the form of a solid, paste or gel, or in a form otherwise unsuitable for direct measurement of the pH, a suitable aliquot of a 10% aqueous solution of the product; and

  • (b) calculating

    • (i) in the case of an acidic product, the amount of an alkali, expressed in grams of sodium hydroxide, that is required to bring 100 mL of the product in the form of a liquid, or 100 g of the product in the form of a solid, paste or gel, to a pH of 4.00 ± 0.05, and

    • (ii) in the case of a basic product, the amount of an alkali, expressed in grams of sodium hydroxide, that is neutralized when 100 mL of the product in the form of a liquid, or 100 g of the product in the form of a solid, paste or gel, is brought to a pH of 10.00 ± 0.05 by the addition of hydrochloric acid.

• Marginal note:Unstable end point

  (3) If the end point of the titration referred to in subsection (2) is unstable and exhibits drifting, the pH end point reached within 30 seconds after the last addition of titrant is to be used as the effective end point for classification purposes.

Very Corrosive Products

Marginal note:Conditions

45 The manufacturing, importation, advertising or sale of a corrosive product that is classified in the sub-category “very corrosive” under section 41 is prohibited unless the product is set out in column 1 of the table to this section and meets the conditions set out in column 2.

Required Information

Marginal note:Required information — sub-category “very corrosive”

• 46 (1) When a corrosive product classified in the sub-category “very corrosive” under section 41 has an information requirement under the table to section 45, the container of the product must display, for each type of information set out in column 1 of the table to this subsection and for each applicable route of exposure set out in column 2, the information set out in columns 3 and 4, other than the instructions set out in italics.

  	Column 1	Column 2	Column 3	Column 4
  Item	Type of information	Applicable route of exposure	English information	French information
  1	Hazard symbol	All
  2	Signal word	All	EXTREME DANGER	DANGER EXTRÊME
  3	Primary hazard statement	All	VERY CORROSIVE	TRÈS CORROSIF
  4	Specific hazard statement	(a) All	CAUSES SEVERE BURNS	PROVOQUE DE GRAVES BRÛLURES
  		(b) Dermal and contains a concentration of 0.5% or more of available fluoride ions	SYMPTOMS MAY NOT APPEAR IMMEDIATELY	LES SYMPTOMES PEUVENT NE PAS SE MANIFESTER IMMÉDIATEMENT
  		(c) Inhalation	When appropriate: DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS	When appropriate: DÉGAGE DES ÉMANATIONS DANGEREUSES LORSQUE MÉLANGÉ AVEC D’AUTRES PRODUITS
  5	Negative instructions	(a) All	When appropriate and before the other negative instructions: Do not mix with [Insert description of other products that react with the chemical product, such as toilet bowl or drain cleaners, bleach or ammonia.].	When appropriate and before the other negative instructions: Ne pas mélanger avec [Insert description of other products that react with the chemical product, such as des nettoyants pour cuvettes de toilette ou tuyaux d’évacuation, des agents de blanchiment ou de l’ammoniaque.].
  		(b) Oral	Do not swallow.	Ne pas avaler.
  		(c) Eyes	Do not get in eyes.	Éviter tout contact avec les yeux.
  		(d) Dermal	Do not get on skin or clothing.	Éviter tout contact avec la peau ou les vêtements.
  		(e) Inhalation	Do not breathe fumes.	Ne pas respirer les émanations.
  6	Positive instructions	(a) All	Handle with extreme care. Keep out of reach of children.	Manipuler avec grand soin. Tenir hors de la portée des enfants.
  		(b) Oral	Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., a mask.].	Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., un masque.].
  		(c) Dermal	Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., rubber gloves, safety glasses.].	Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., des gants de caoutchouc, des lunettes de sécurité.].
  		(d) Inhalation	Use only in a well-ventilated area. Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., a mask, a respirator].	N’utiliser que dans un endroit bien aéré. Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., un masque, un respirateur.].
  7	First aid statement	(a) All	FIRST AID TREATMENT Contains [name of hazardous ingredients in descending order of proportion]. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting.	PREMIERS SOINS Contient [name of hazardous ingredients in descending order of proportion]. En cas d’ingestion, appeler immédiatement un centre antipoison ou un médecin. Ne pas provoquer le vomissement.
  		(b) Eyes	If in eyes, rinse with water for [Insert appropriate period of time.].	En cas de contact avec les yeux, rincer avec de l’eau pendant [Insert appropriate period of time.].
  		(c) Dermal	If on skin, rinse well with water. If on clothes, remove clothes.	En cas de contact avec la peau, bien rincer avec de l’eau En cas de contact avec les vêtements, enlever ceux-ci.
  		(d) Inhalation	If breathed in, move person to fresh air.	En cas d’inhalation, transporter à l’air frais la personne exposée.

• Marginal note:Required information — sub-category “corrosive”

  (2) The container of a corrosive product that is classified in the sub-category “corrosive” under section 41 must display, for each type of information specified in column 1 of the table to this subsection and for each applicable route of exposure set out in column 2, the information set out in columns 3 and 4, other than the instructions set out in italics.

  	Column 1	Column 2	Column 3	Column 4
  Item	Type of information	Applicable route of exposure	English information	French information
  1	Hazard symbol	All
  2	Signal word	All	DANGER	DANGER
  3	Primary hazard statement	All	CORROSIVE	CORROSIF
  4	Specific hazard statement	(a) All	CAUSES BURNS	PROVOQUE DES BRÛLURES
  		(b) Inhalation	When appropriate: DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS	When appropriate: DÉGAGE DES ÉMANATIONS DANGEREUSES LORSQUE MÉLANGÉ AVEC D’AUTRES PRODUITS
  5	Negative instructions	(a) All	When appropriate and before the other negative instructions: Do not mix with [Insert description of other products that react with the chemical product, such as toilet bowl or drain cleaners, bleach or ammonia.].	When appropriate and before the other negative instructions: Ne pas mélanger avec [Insert description of other products that react with the chemical product, such as des nettoyants pour cuvettes de toilette ou tuyaux d’évacuation, des agents de blanchiment ou de l’ammoniaque.].
  		(b) Oral	Do not swallow.	Ne pas avaler.
  		(c) Eyes	Do not get in eyes.	Éviter tout contact avec les yeux.
  		(d) Dermal	Do not get on skin or clothing.	Éviter tout contact avec la peau ou les vêtements.
  		(e) Inhalation	Do not breathe fumes.	Ne pas respirer les émanations.
  6	Positive instructions	(a) All	Handle with care. Keep out of reach of children.	Manipuler avec soin. Tenir hors de la portée des enfants.
  		(b) Oral	Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., a mask.].	Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., un masque.].
  		(c) Dermal	Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., rubber gloves, safety glasses.].	Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., des gants de caoutchouc, des lunettes de sécurité.].
  		(d) Inhalation	Use only in a well-ventilated area. Wear [Insert description of the specific safety equipment relevant to the hazard, e.g., a mask, a respirator.].	N’utiliser que dans un endroit bien aéré. Porter [Insert description of the specific safety equipment relevant to the hazard, e.g., un masque, un respirateur.].
  7	First aid statement	(a) All	FIRST AID TREATMENT Contains [name of hazardous ingredients in descending order of proportion]. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting.	PREMIERS SOINS Contient [name of hazardous ingredients in descending order of proportion]. En cas d’ingestion, appeler immédiatement un centre antipoison ou un médecin. Ne pas provoquer le vomissement.
  		(b) Eyes	If in eyes, rinse with water for [Insert appropriate period of time.].	En cas de contact avec les yeux, rincer avec de l’eau pendant [Insert appropriate period of time.].
  		(c) Dermal	If on skin, rinse well with water. If on clothes, remove clothes.	En cas de contact avec la peau, bien rincer avec de l’eau. En cas de contact avec les vêtements, enlever ceux-ci.
  		(d) Inhalation	If breathed in, move person to fresh air.	En cas d’inhalation, transporter à l’air frais la personne exposée.

• Marginal note:Required information — sub-category “irritant”

  (3) Subject to subsection (4), the container of a corrosive product that is classified in the sub-category “irritant” under section 41 must display, for each type of information specified in column 1 of the table to this subsection and for each applicable route of exposure set out in column 2, the information set out in columns 3 and 4, other than the instructions set out in italics.

  	Column 1	Column 2	Column 3	Column 4
  Item	Type of information	Applicable route of exposure	English information	French information
  1	Signal word	Dermal	CAUTION	ATTENTION
  2	Primary hazard statement	Dermal	IRRITANT	IRRITANT
  3	Specific hazard statement	(a) Eye	MAY IRRITATE EYES	PEUT IRRITER LES YEUX
  		(b) Dermal	MAY IRRITATE SKIN	PEUT IRRITER LA PEAU
  		(c) Inhalation	When appropriate: DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS	When appropriate: DÉGAGE DES ÉMANATIONS DANGEREUSES LORSQUE MÉLANGÉ AVEC D’AUTRES PRODUITS
  4	Negative instructions	(a) All	When appropriate and before the other negative instructions: Do not mix with [Insert description of other products that react with the chemical product, such as toilet bowl or drain cleaners, bleach or ammonia.].	When appropriate and before the other negative instructions: Ne pas mélanger avec [Insert description of other products that react with the chemical product, such as des nettoyants pour cuvettes de toilette ou tuyaux d’évacuation, des agents de blanchiment ou de l’ammoniaque.].
  		(b) Eyes	Do not get in eyes.	Éviter tout contact avec les yeux.
  		(c) Dermal	Do not get on skin or clothing.	Éviter tout contact avec la peau ou les vêtements.
  		(d) Inhalation	Do not breathe fumes.	Ne pas respirer les émanations.
  5	Positive instructions	All	Keep out of reach of children.	Tenir hors de la portée des enfants.
  6	First aid statement	(a) All	FIRST AID TREATMENT Contains [name of hazardous ingredients in order of decreasing proportion]. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting.	PREMIERS SOINS Contient [name of hazardous ingredients in order of decreasing proportion]. En cas d’ingestion, appeler immédiatement un centre antipoison ou un médecin. Ne pas provoquer le vomissement.
  		(b) Eyes	If in eyes, rinse with water for [Insert appropriate period of time.].	En cas de contact avec les yeux, rincer avec de l’eau pendant [Insert appropriate period of time.].
  		(c) Dermal	If on skin, rinse well with water.	En cas de contact avec la peau, bien rincer avec de l’eau.

• Marginal note:Exception — another primary hazard statement

  (4) The primary hazard statement set out in columns 3 and 4 of item 2 of the table to subsection (3) may be omitted when other provisions in these Regulations require another primary hazard statement to be displayed on the container.

Child-resistant Containers

Marginal note:Sub-categories “very corrosive” and “corrosive”

47 Subject to section 14, a corrosive product must be in a child-resistant container that complies with sections 9 to 13 if the product has been classified in accordance with section 41

• (a) in the sub-category “very corrosive” and is listed in the table to section 45; or

• (b) in the sub-category “corrosive”.

PART 3Flammable Products

Classification of Flammable Products

Marginal note:Data sources and tests

• 48 (1) The responsible person for a flammable product must determine the appropriate sub-category for the product in accordance with section 49 using human experience data or the results of tests conducted in accordance with the test methods set out in sections 50 to 52 and Schedule 1.

• Marginal note:Exemption

  (2) A flammable product that is classified in the sub-category “combustible” is exempt from the requirements of this Part if it

  • (a) is composed of 50% or more of water and 50% or less of water-miscible solvent; and

  • (b) does not sustain combustion when tested in accordance with Test L.2.

Marginal note:Sub-categories of hazard category “Category 3, flammable products”

• 49 (1) A flammable product described in column 1 of the table to this subsection must be classified in the sub-category set out in column 2.

  	Column 1	Column 2
  Item	Product Description	Sub-category
  1	A product that spontaneously combusts under reasonably foreseeable conditions of use	Spontaneously Combustible
  2	A product that heats spontaneously on contact with air to the point that it begins to burn	Spontaneously Combustible
  3	A liquid, other than a liquid in a spray container, that has a flash point, determined in accordance with one of the standards set out in section 50, of
  	(a) less than -18.0°C;	Very Flammable
  	(b) -18.0°C or more but not more than 37.8°C; or	Flammable
  	(c) more than 37.8°C but not more than 60.0°C	Combustible
  4	A solid, paste or gel that emits a vapour that has a flash point, determined in accordance with the standard set out in section 51, of
  	(a) less than -18.0°C;	Very Flammable
  	(b) -18.0°C or more but not more than 37.8°C; or	Flammable
  	(c) more than 37.8°C but not more than 60.0°C	Combustible
  5	A gas, other than a gas in a spray container, that forms a flammable mixture with air at a concentration of 13% or less by volume at normal atmospheric pressure	Flammable
  6	A gas, other than a gas in a spray container, that forms a flammable mixture with air over a concentration range of 12% or more by volume at normal atmospheric pressure	Flammable
  7	A liquid or gas in a spray container that, when tested in accordance with the procedure set out in Schedule 1,
  	(a) has a flame projection of 100 cm or more;	Very Flammable
  	(b) has a flame projection of 15 cm or more but less than 100 cm; or	Flammable
  	(c) exhibits a flashback	Very Flammable

• Marginal note:Flammable liquid in a refillable spray container

  (2) In the case of a liquid flammable product in a refillable spray container, the responsible person must

  • (a) determine both the product’s flash point, in accordance with section 50, and its flame projection and flashback, in accordance with section 52; and

  • (b) classify the product in the most flammable sub-category of the applicable sub-categories as determined under items 3 and 7 of the table to subsection (1).

Test Methods

Marginal note:Flash point — liquids

50 A flammable product in the form of a liquid must be tested for its flash point in accordance with the following standards:

• (a) for liquids that have a viscosity of less than 5.8 mm²/s at 37.8°C, ASTM D 56 or ASTM D 3828; and

• (b) for liquids that have a viscosity of 5.8 mm²/s or more at 37.8°C, ASTM D 93.

Marginal note:Flash point — solids, pastes and gels

51 A flammable product in the form of a solid, paste or gel must be tested for its flash point in accordance with ASTM D 56.

Marginal note:Flame projection and flashback — spray container

52 A flammable product that is enclosed in a spray container must be tested for its flame projection and flashback in accordance with the procedure set out in Schedule 1.

Very Flammable Products

Marginal note:Conditions

53 The manufacturing, importation, advertising or sale of a flammable product that is classified in the sub-category “very flammable” under section 48 is prohibited unless the product is set out in column 1 of the table to this section and meets the conditions set out in column 2.

Required Information

Marginal note:Required information — sub-category “very flammable”

• 54 (1) When a flammable product classified in the sub-category “very flammable” under section 48 has an information requirement under the table to section 53, the container of the product must display, for each type of information set out in column 1 of the table to this subsection, the information set out in columns 2 and 3, other than the instructions set out in italics.

  	Column 1	Column 2	Column 3
  Item	Type of information	English information	French information
  1	Hazard symbol
  2	Signal word	EXTREME DANGER	DANGER EXTRÊME
  3	Primary hazard statement	VERY FLAMMABLE	TRÈS INFLAMMABLE
  4	Specific hazard statement	CONTENTS MAY CATCH FIRE or, when only the vapour or fume poses a hazard: FUMES MAY CATCH FIRE	LE CONTENU PEUT S’ENFLAMMER or, when only the vapour or fume poses a hazard: LES ÉMANATIONS PEUVENT S’ENFLAMMER
  5	Negative instructions	Do not smoke.	Ne pas fumer.
  6	Positive instructions	Use only in a well-ventilated area. Keep away from flames, such as a pilot light, and any object that sparks, such as an electric motor.	N’utiliser que dans un endroit bien aéré. Tenir loin des flammes, telle une flamme pilote, et de tout objet produisant des étincelles, tel un moteur électrique.

• Marginal note:Required information — sub-category “flammable”

  (2) The container of a flammable product that is classified in the sub-category “flammable” under section 48 must display, for each type of information set out in column 1 of the table to this subsection, the information set out in columns 2 and 3, other than the instructions set out in italics.

  	Column 1	Column 2	Column 3
  Item	Type of information	English information	French information
  1	Hazard symbol
  2	Signal word	DANGER	DANGER
  3	Primary hazard statement	FLAMMABLE	INFLAMMABLE
  4	Specific hazard statement	CONTENTS MAY CATCH FIRE or, when only the vapour or fume poses a hazard: FUMES MAY CATCH FIRE	LE CONTENU PEUT S’ENFLAMMER or, when only the vapour or fume poses a hazard: LES ÉMANATIONS PEUVENT S’ENFLAMMER
  5	Negative instructions	Do not smoke.	Ne pas fumer.
  6	Positive instructions	Use only in a well-ventilated area. Keep away from flames, such as a pilot light, and any object that sparks, such as an electric motor.	N’utiliser que dans un endroit bien aéré. Tenir loin des flammes, telle une flamme pilote, et de tout objet produisant des étincelles, tel un moteur électrique.

• Marginal note:Required information — sub-category “spontaneously combustible”

  (3) The container of a flammable product that is classified in the sub-category “spontaneously combustible” under section 48 must display, for each type of information set out in column 1 of the table to this subsection, the information set out in columns 2 and 3.

  	Column 1	Column 2	Column 3
  Item	Type of information	English information	French information
  1	Hazard symbol
  2	Signal word	CAUTION	ATTENTION
  3	Primary hazard statement	READ INSTRUCTIONS BEFORE USING	LIRE LES INSTRUCTIONS AVANT USAGE
  4	Specific hazard statement	DANGER OF COMBUSTION	DANGER DE COMBUSTION
  5	Positive instructions	Materials such as rags used with this product may begin to burn by themselves. After use, put rags in water or lay flat to dry, then discard.	Les matériaux, utilisés avec ce produit, tels les chiffons, peuvent s’enflammer spontanément. Après utilisation, mettre les chiffons dans l’eau ou les sécher à plat, puis les jeter.

• Marginal note:Required information — sub-category “combustible”

  (4) The container of a flammable product that is classified in the sub-category “combustible” under section 48 must display, for each type of information set out in column 1 of the table to this subsection, the information set out in columns 2 and 3.

  	Column 1	Column 2	Column 3
  Item	Type of information	English information	French information
  1	Positive instructions	Keep away from flames or sparks.	Tenir loin des flammes et des étincelles.

PART 4Quick Skin-bonding Adhesives

Marginal note:Required instructions and first aid statement

55 The container of a quick skin-bonding adhesive must display the instructions and first aid statement set out in section 56 in the manner set out in sections 17 to 20, 24, 25 and 29 to 32.

Marginal note:Required information

• 56 (1) Subject to subsection (2), the container of a quick skin-bonding adhesive must display, for each type of information set out in column 1 of the table to this subsection, the information set out in columns 2 and 3.

  	Column 1	Column 2	Column 3
  Item	Type of information	English information	French information
  1	Signal word	CAUTION	ATTENTION
  2	Primary hazard statement	BONDS SKIN INSTANTLY	COLLE RAPIDEMENT LA PEAU
  3	Negative instructions	Do not get in eyes or mouth or on skin.	Éviter tout contact avec les yeux, la peau et la bouche.
  4	Positive instructions	Keep out of reach of children.	Tenir hors de la portée des enfants.
  5	First aid statement	FIRST AID TREATMENT Contains [name of hazardous ingredients in descending order of proportion]. Eyelid bonding: see a doctor. Skin bonding: soak skin in water and call a Poison Control Centre. Do not force apart.	PREMIERS SOINS Contient [name of hazardous ingredients in descending order of proportion]. Paupières collées : consulter un médecin. Peau collée : tremper dans l’eau et appeler un centre antipoison. Ne pas forcer pour décoller.

• Marginal note:Exception — main display panel less than 35 cm²

  (2) The container of a quick skin-bonding adhesive that has a main display panel of less than 35 cm² need only display the information set out in columns 2 and 3 of items 2 and 5 of the table to subsection (1) in the height and body size of type set out in subsection 24(3).

Marginal note:Child-resistant container

• 57 (1) Subject to subsection (2), a quick skin-bonding adhesive must be in a child-resistant container that complies with sections 9 to 13.

• Marginal note:Exception — child-resistant packaging

  (2) Subsection (1) does not apply if the packaging that immediately encloses the container and that is displayed to the consumer is child-resistant and complies with sections 9 to 13.

PART 5Pressurized Containers

Marginal note:Application

• 58 (1) Subject to subsection (2), this Part applies to a pressurized container that

  • (a) contains or will contain a substance that, when in a liquid state, has an absolute vapour pressure greater than 275 kPa at 37.8°C as determined using ASTM D 323; or

  • (b) is or will be pressurized to an absolute pressure greater than 275 ± 1 kPa at 21.1°C or 717 ± 2 kPa at 54.4°C.

• Marginal note:Exceptions

  (2) This Part does not apply to a pressurized container that complies with CSA B339.

Marginal note:Required information

59 A pressurized container must display, for each type of information set out in column 1 of the table to this section, the information set out in columns 2 and 3.

	Column 1	Column 2	Column 3
Item	Type of information	English information	French information
1	Hazard symbol
2	Signal word	CAUTION	ATTENTION
3	Primary hazard statement	CONTENTS UNDER PRESSURE	CONTENU SOUS PRESSION
4	Specific hazard statement	CONTAINER MAY EXPLODE IF HEATED	CE CONTENANT PEUT EXPLOSER S’IL EST CHAUFFÉ
5	Negative instructions	Do not puncture. Do not burn.	Ne pas perforer. Ne pas brûler.
6	Positive instructions	Store away from heat.	Conserver loin des sources de chaleur.

60 [Repealed, SOR/2009-165, s. 17]

Repeal

61 [Repeal]

Coming into Force

Marginal note:Coming into force

62 These Regulations come into force on October 1, 2001.

SCHEDULE 1(Subsections 1(1), 48(1) and 49(1) and section 52)Test for Determining the Flashback and the Length of the Flame Projection of a Flammable Product Enclosed in a Spray Container

Application

• 1 This test is to be used to determine the flashback and the length of the flame projection of a flammable product enclosed in a spray container.

Apparatus

• 2 The following apparatus is to be used in this test:

  • (a) a flammability tester, as illustrated in Figures 1 and 2 to the Schedule, that

    • (i) is constructed so that the spray container can be secured in place by means of a holding device, such as a three-pronged clamp affixed to a ring stand, in such a manner that the discharge from the spray container is in the horizontal plane,

    • (ii) may include a remote control device by which

      • (A) the valve of a pressurized container can be activated, such as a side-pull, caliper-type bicycle hand brake, or

      • (B) the trigger or plunger of a pump-spray container can be pneumatically activated, as illustrated in Figures 3 and 4 to the Schedule,

    • (iii) has a vertically mounted burner that

      • (A) has an inside diameter of 1.2 mm,

      • (B) has a Luer-Lock 16-gauge needle affixed to a metal tube or another suitable device, and

      • (C) is placed at a distance of 15 cm from the discharge orifice of the spray container, which distance is to be measured horizontally between the vertical planes of the discharge orifice and the burner orifice, and

    • (iv) has two support frameworks, placed on the opposite side of the burner from the spray container, one at a distance of 15 cm from the burner and the other at a distance of 100 cm from the burner, each of which

      • (A) has an internal open space of 35 cm wide by 45 cm high,

      • (B) is constructed from metal or other non-flammable material,

      • (C) is mounted in a vertical plane perpendicular to the direction of discharge from the spray container, and

      • (D) is adjustable in the vertical plane;

  • (b) a cylinder of chemically pure grade propane fitted with a regulator capable of delivering pressure to the burner appropriate to maintaining a flame height of 5 cm; and

  • (c) loosely woven cotton fabric commonly referred to as cheesecloth that has, in the bleached state, a mass per unit area of not less than 35 g/m² and not more than 65 g/m².

Test Specimen

• • 3 (1) When there are instructions by the manufacturer respecting the shaking of the spray container, a test must be conducted as follows, using each of three spray containers of the same product and of the same size:

    • (a) if shaking is applicable, shake and discharge the container three times in the manner described in paragraph 4(9)(a); or

    • (b) if shaking is not applicable, discharge the container three times in the manner described in paragraph 4(9)(b).

  • (2) When there are no instructions by the manufacturer respecting the shaking of the spray container, a test must be conducted as follows, using each of three spray containers of the same product and of the same size:

    • (a) without shaking the container, discharge it three times in the manner described in paragraph 4(9)(b); and

    • (b) shake and discharge the container a further three times in the manner described in paragraph 4(9)(a).

Procedure

• • 4 (1) A test

    • (a) must be conducted at a room temperature of 22 ± 2°C in the absence of air currents, with an allowance made for a clearance of 50 cm beyond the support framework that is set at a distance of 100 cm from the burner; and

    • (b) may be conducted in a fume hood with the exhaust fan turned off and the protecting door lowered.

  • (2) Any fume must be removed from the test area and any residue cleaned up after each discharge.

  • (3) Before testing, each spray container must be

    • (a) maintained at a temperature of 22 ± 2°C for at least four hours; and

    • (b) primed by

      • (i) in the case of a pressurized container, discharging the container for five seconds, and

      • (ii) in the case of a pump-spray container, activating the trigger or pump using each of 18 N, 36 N and 54 N of force for each possible nozzle position until

        • (A) in the case of the “stream” position, a continuous stream is produced, and

        • (B) in the case of the “spray” position, a mist is produced.

  • (4) Install the first spray container in the holding device and ensure that the burner orifice is 15 cm from the discharge orifice of the spray container in the horizontal plane and 5 cm below it in the vertical plane and that the discharge orifice points in the direction of the burner.

  • (5) Adjust the burner to give a flame height of 5 cm and release a single trial discharge from the spray container.

  • (6) If the operation set out in subsection (5) does not produce a flame projection, lower the burner orifice by 5 cm and adjust the burner to give a flame height of 12 cm.

  • (7) Attach the cheesecloth to the flammability tester with bulldog clips or in any other manner so as to cover the entire internal space of the support framework set at a distance of 15 cm from the burner and verify that the cheesecloth is at a proper horizontal distance from the vertical plane of the burner orifice on the opposite side of the burner from the spray container.

  • (8) Adjust the height of the support framework so that the cheesecloth will intercept the line of flame projection.

  • (9) Prepare the spray container in accordance with the manufacturer’s instructions and

    • (a) if shaking is applicable,

      • (i) shake vigorously for five seconds, or for the period specified in the manufacturer’s instructions,

      • (ii) install the spray container in the holding device, and

      • (iii) 15 seconds after the cessation of shaking, release the discharge in accordance with subsection (10); or

      • (iv) [Repealed, SOR/2009-165, s. 20]

    • (b) if shaking is not applicable, install the spray container in the holding device and release the discharge in accordance with subsection (10), allowing the spray container to stand for at least 60 seconds between discharges.

  • (10) Discharge the spray container

    • (a) in the case of a pressurized container, for five seconds or until the cheesecloth ignites; or

    • (b) in the case of a pump-spray container, for three sprays or until the cheesecloth ignites.

  • (11) In the case of a pump-spray container, repeat the procedure set out in paragraph (10)(b) for each of 18 N, 36 N and 54 N of force for each possible nozzle position.

  • (12) If the cheesecloth attached to the support framework that is set at a distance of 15 cm from the burner ignites, the remaining discharges referred to in section 3 must be carried out in accordance with subsections (1) to (11) using a new piece of cheesecloth attached to the support framework that is set at a distance of 100 cm from the burner.

Determination and Reporting of Flame Projection and Flashback

• • 5 (1) If at any time during the test the cheesecloth that is mounted at a distance of 100 cm from the burner is ignited, the length of the flame projection is 100 cm or more.

  • (2) If at any time during the test the cheesecloth that is mounted at a distance of 15 cm from the burner is ignited and, at all times during the test, the cheesecloth that is mounted at a distance of 100 cm from the burner remains unignited, the length of the flame projection is 15 cm or more but less than 100 cm.

  • (3) If at any time during the test the cheesecloth mounted at a distance of 15 cm from the burner is not ignited but there is a flame projection, the length of the flame projection is less than 15 cm.

• 6 The following test results must be recorded and kept for a period of at least three years after the testing is carried out:

  • (a) the length of the flame projection

    • (i) in the case of a pressurized container, for each discharge, and

    • (ii) in the case of a pump-spray container, for each discharge at each nozzle position and each force applied;

  • (b) a lack of flame projection resulting from any of the test discharges; and

  • (c) any flashback.

FIGURE 1Flammability TesterPressurized Container

FIGURE 2Flammability TesterPump-Spray Container

FIGURE 3Holding Apparatus for a Trigger-Type ContainerIsometric View

FIGURE 4Holding Apparatus for a Plunger Type or Pressurized ContainerIsometric View

• SOR/2009-165, ss. 18 to 21

SCHEDULE 2(Subsection 1(1) and section 21)

	Column 1	Column 2
Item	Description	Symbol
1	TOXIC
2	CORROSIVE
3	FLAMMABLE
4	EXPLOSIVE

SCHEDULE 4(Paragraph 19(1)(b))