Part I

1.1 [Repealed, SOR/2002-208, s. 2]

Interpretation

1.2 In these Regulations,

Act

Act means Part II of the Canada Labour Code; (Loi)

ANSI

ANSI means the American National Standards Institute; (ANSI)

approved organization

approved organization means an organization that is approved by any province for the teaching of first aid; (organisme agréé)

basic first aid certificate

basic first aid certificate means the certificate issued by either a qualified person or the organization that developed the training, as the case may be, for successful completion of a one-day first aid course; (certificat de secourisme élémentaire)

change room

change room means a room that is used by employees to change from their street clothes to their work clothes and from their work clothes to their street clothes, and includes a locker room; (vestiaire)

CSA

CSA means the Canadian Standards Association; (ACNOR)

dangerous substance

dangerous substance[Repealed, SOR/88-68, s. 1]

elevating device

elevating device means an escalator, elevator or other device for moving passengers or freight; (appareil élévateur)

fire hazard area

fire hazard area means an area that contains or is likely to contain explosive or flammable concentrations of hazardous substances; (endroit présentant un risque d’incendie)

first aid room

first aid room means a room that complies with the requirements of section 16.10; (salle de premiers soins)

high voltage

high voltage means a voltage of 751 volts or more between any two conductors or between a conductor and ground; (haute tension)

locked out

locked out means, in respect of any equipment, machine or device, that the equipment, machine or device has been rendered inoperative and cannot be operated or energized without the consent of the person who rendered it inoperative; (verrouillé)

lower explosive limit

lower explosive limit means the lower limit of flammability of a chemical agent or a combination of chemical agents at ambient temperature and pressure, expressed

• (a) for a gas or vapour, as a percentage in air by volume, and

• (b) for dust, as the weight of dust per volume of air; (limite explosive inférieure)

medical practitioner

medical practitioner[Repealed, SOR/88-68, s. 1]

Minister

Minister means the Minister of Labour; (ministre)

National Building Code

National Building Code means the National Building Code of Canada, 1995, issued by the Canadian Commission on Building and Fire Codes, National Research Council of Canada, dated 1995, as amended from time to time; (Code canadien du bâtiment)

National Fire Code

National Fire Code means the National Fire Code of Canada 1995, issued by the Canadian Commission on Building and Fire Codes, National Research Council of Canada, dated 1995, as amended from time to time; (Code national de prévention des incendies du Canada)

oxygen deficient atmosphere

oxygen deficient atmosphere means an atmosphere in which there is less than 18 per cent by volume of oxygen at a pressure of one atmosphere or in which the partial pressure of oxygen is less than 135 mm Hg; (air à faible teneur en oxygène)

personal service room

personal service room means a change room, toilet room, shower room, lunch room, living space, sleeping quarters or a combination thereof; (local réservé aux soins personnels)

protection equipment

protection equipment means safety materials, equipment, devices and clothing; (équipement de protection)

qualified person

qualified person means, in respect of a specified duty, a person who, because of his knowledge, training and experience, is qualified to perform that duty safely and properly; (personne qualifiée)

regional office

regional office, in respect of a work place, means the office of the Department of Employment and Social Development that is responsible for the HRSDC Labour Program in any of the Department’s administrative regions in which the workplace is situated; (bureau régional)

toilet room

toilet room means a room that contains a toilet or a urinal, but does not include an outdoor privy. (lieux d’aisances)

Prescription

1.3 These Regulations are prescribed for the purposes of sections 125, 125.1, 125.2 and 126 of the Act.

Application

1.4 These Regulations do not apply in respect of employees employed

• (a) on trains while in operation;

• (b) on aircraft while in operation;

• (c) on ships;

• (d) subject to Part II of the Oil and Gas Occupational Safety and Health Regulations, on or in connection with exploration or drilling for or the production, conservation, processing or transportation of oil or gas in frontier lands, as that term is defined in the Canada Petroleum Resources Act; or

• (e) on or in connection with a work or undertaking that is excluded from the application of the Act by an order made pursuant to section 123.1 of the Act.

Records and Reports

1.5 If an employer is required by section 125 or 125.1 of the Act to keep and maintain a record, report or other document, the employer shall keep and maintain the record, report or other document in such a manner that it is readily available for examination by a health and safety officer and by the work place committee or the health and safety representative for the work place to which it applies.

Inconsistent Provisions

1.6 In the event of an inconsistency between any standard incorporated by reference in these Regulations and any other provision of these Regulations, that other provision shall prevail to the extent of the inconsistency.

1.7 Notwithstanding any provision in any standard incorporated by reference in these Regulations, a reference to another publication in that standard is a reference to the publication as it read on March 31, 1986.

Alternate Media

• 1.8 (1) In this section,

  alternate media

  alternate media means any method of communication that permits an employee with a special need to receive any information, instruction or training required by these Regulations to be provided, including braille, large print, audio tape, computer disc, sign language and verbal communications; (média substitut)

  highly visible

  highly visible means marked with brightly coloured paint, painted with a reflective coating or marked by other means so as to be readily apparent; (très visible)

  special need

  special need means a condition that impairs an employee’s ability to receive any information, instruction or training that is required by these Regulations to be provided. (besoins spéciaux)

• (2) Subject to subsection (5), where an employer or other person is required by these Regulations to give, provide or make available any information, instruction or training to an employee and the employee has a special need, the employer or other person shall give, provide or make available the information, instruction or training to the employee by means of an alternate medium.

• (3) Where information, including warnings, is required by these Regulations to be provided by means of a sign or marking, the alternate medium shall be visible or audible to an employee with a special need.

• (4) Where a warning is required to be given by a means other than a sign or marking, the warning shall be given to an employee with a special need in a manner that effectively warns the employee of the nature of the danger.

• (5) Where an employer or other person is required by these Regulations to give, provide or make available any information by means of labels, defect tags or lockout tags, the employer or other person need not provide the information by means of an alternate medium on the labels, defect tags or lockout tags.

PART IIPermanent Structures

Interpretation

2.1 The definitions in this section apply in this Part.

ASHRAE

ASHRAE means the American Society of Heating, Refrigerating and Air-Conditioning Engineers. (ASHRAE)

building

building means a structure that is used or intended for supporting or sheltering any use or occupancy, and includes a grain-handling facility, a tower, an antenna and an antenna-supporting structure. (bâtiment)

floor hole

floor hole means an opening in a floor or platform that measures less than 300 mm but more than 50 mm in its smallest dimension. (trou dans le plancher)

floor opening

floor opening means an opening in a floor, platform, pavement or yard that measures 300 mm or more in its smallest dimension. (ouverture dans le plancher)

grain-handling facility

grain-handling facility means a structure that is constructed, installed or established to handle, store or process grain or grain products, and includes an elevator as defined in section 2 of the Canada Grain Act. (installation de manutention des grains)

HVAC system

HVAC system means a heating, ventilating and air conditioning system that is installed in a building, and includes all of its equipment and components. (système CVCA)

wall opening

wall opening means an opening in a wall or partition that measures at least 750 mm in height and 300 mm in width. (ouverture dans un mur)

DIVISION IBUILDINGS

Standards

• 2.2 (1) The design and construction of every building, the construction of which begins on or after the day of the coming into force of this subsection, shall meet the requirements of the National Building Code.

• (2) Every building, the construction of which begins before the day of the coming into force of this subsection, shall, to the extent reasonably practicable, meet the requirements of the National Building Code.

• (3) The renovation of any building or part of a building shall, to the extent reasonably practicable, meet the requirements of the National Building Code.

• (4) When it is not reasonably practicable for an employer to comply with the requirements of subsection (3), the employer shall, before the proposed renovations start, notify the work place committee or the health and safety representative.

Doors

• 2.3 (1) Every double-action swinging door that is located in an exit, entrance or passageway used for two-way pedestrian traffic or traffic involving wheelchairs or other similar devices shall be designed and fitted in a manner that will allow persons who are approaching from one side of the door to be aware of persons who are on the other side of it.

• (2) The area of every passageway into which a door or gate extends when open, other than the door of a closet or other small unoccupied storage room, shall be marked, in consultation with the work place committee or the health and safety representative in a manner that clearly indicates the area of hazard created by the opening of the door or gate.

• (3) Where a door or gate that is to remain open extends into a passageway for a distance that will reduce the effective width of the passageway to a width less than that required by the National Building Code,

  • (a) an attendant shall be posted near the open door or gate; or

  • (b) a highly visible barricade shall be placed across the passageway before the door or gate is opened to prevent persons from using the passageway while the door or gate is open.

Clearances

2.4 A window awning or canopy or any part of a building that projects over an exterior passageway shall be installed or constructed in a manner that allows a clearance of not less than 2.2 m between the passageway surface and the lowest projection of the awning or canopy or projecting part of the building.

Floor and Wall Openings

• 2.5 (1) Where an employee has access to a wall opening from which there is a drop of more than 1.2 m or to a floor opening, highly visible guardrails shall be fitted around the wall opening or floor opening or it shall be covered with material capable of supporting all loads that may be brought to bear on it.

• (2) The material shall be securely fastened to and supported by structural members.

• (3) Subsection (1) does not apply to vehicle maintenance pits or to the loading and unloading areas of truck, railroad or marine docks the edges of which are marked in a highly visible manner.

• (4) Where a pit is used for the maintenance of vehicles, including railway rolling stock, the hazard it represents shall be clearly identified and its perimeter shall be delineated by highly visible markings.

Open-top Bins, Hoppers, Vats and Pits

• 2.6 (1) Where an employee has access to an open-top bin, hopper, vat, pit or other open-top enclosure from a point directly above the enclosure, the enclosure shall be

  • (a) covered with a grating, screen or other covering that will prevent the employee from falling into the enclosure; or

  • (b) provided with a walkway that is not less than 500 mm wide and is fitted with highly visible guardrails.

• (2) The grating, screen, covering or walkway shall be designed, constructed and maintained so that it will support a load that is not less than the greater of

  • (a) the maximum load that may be brought to bear on it, and

  • (b) a live load of 6 kPa.

• (3) Where an employee is working above an open-top bin, hopper, vat, pit or other open-top enclosure that is not covered with a grating, screen or other covering, the inside wall of the enclosure shall be fitted with a fixed ladder, except where the operations carried on in the enclosure make such a fitting impracticable.

• (4) Every enclosure referred to in subsection (1) whose walls extend less than 1.1 m above an adjacent floor or platform used by employees shall be

  • (a) covered with a grating, screen or other covering;

  • (b) fitted with a highly visible guardrail; or

  • (c) guarded by a person in order to prevent employees from falling into the enclosure.

Ladders, Stairways and Ramps

2.7 Where an employee is required to move from one level to another that is more than 450 mm higher or lower than the first level, the employer shall install a fixed ladder, stairway or ramp between the levels.

2.8 Where one end of a stairway is so close to a traffic route used by vehicles, to a machine or to any other hazard as to be hazardous to the safety of an employee using the stairway, the employer shall, at that end of the stairway,

• (a) post a sign to warn employees of the hazard; and

• (b) where practicable, install a highly visible barricade that will protect employees using the stairway from the hazard.

• 2.9 (1) A fixed ladder installed after the day of the coming into force of this section shall be designed, constructed and installed in accordance with the requirements of ANSI Standard A14.3-1984 entitled American National Standard for Ladders — Fixed — Safety Requirements, as amended from time to time, other than section 7 of that Standard.

• (2) A fixed ladder that is installed before the day of the coming into force of this section shall, where reasonably practicable, meet the requirements referred to in subsection (1).

• (3) While ascending or descending a fixed ladder, an employee shall

  • (a) maintain a three-point contact with the ladder; and

  • (b) carry any tools, equipment or materials in a pouch or holster or in any other secure manner.

• (4) A fixed ladder shall be highly visible or its presence otherwise brought to the attention of any employee in the area.

• 2.10 (1) Every grain-handling facility that has a manlift or ladder that provides access to a floor or roof over a grain bin or silo shall, in addition to its primary exit, have a secondary exit from the floor or roof that consists of an exterior fixed ladder constructed in accordance with the requirements referred to in subsection 2.9(1).

• (2) A fixed ladder that is installed in a grain-handling facility before the day of the coming into force of this section shall, where reasonably practicable, meet the requirements referred to in subsection 2.9(1).

• (3) A fixed ladder that is installed adjacent to a manlift and that is intended for emergency exit from the manlift shall meet the requirements of section 5.1.9 of CSA Standard B 311-M1979, entitled Safety Code for Manlifts, the English version of which is dated October 1979 and the French version of which is dated July 1984.

Docks, Ramps and Dock Plates

• 2.11 (1) Every loading and unloading dock and ramp shall be

  • (a) of sufficient strength to support the maximum load that may be brought to bear on it;

  • (b) free of surface irregularities that may interfere with the safe operation of mobile equipment; and

  • (c) fitted around its sides that are not used for loading or unloading with side rails, curbs or rolled edges of sufficient height and strength to prevent mobile equipment from running over the edge.

• (2) Cross-traffic on dock levellers shall be limited to the portion of the dock leveller where there is no danger of tipping the materials handling equipment.

• (3) Every portable ramp and every dock plate shall be

  • (a) clearly marked or tagged to indicate the maximum safe load that it is capable of supporting; and

  • (b) installed so that it cannot slide, move or otherwise be displaced under the load that may be brought to bear on it.

Guardrails

• 2.12 (1) Every guardrail shall be highly visible and consist of

  • (a) a horizontal top rail not less than 900 mm but not more than 1 100 mm above the base of the guardrail;

  • (b) a horizontal intermediate rail spaced midway between the top rail and the base; and

  • (c) supporting posts spaced not more than 3 m apart at their centres.

• (2) Every guardrail shall be designed to withstand a static load of 890 N applied in any direction at any point on the top rail.

Toe Boards

2.13 Where there is a hazard that tools or other objects may fall onto a person from a platform or other raised area, or through a floor opening or floor hole,

• (a) a toe board that extends from the floor of the platform or other raised area to a height of not less than 125 mm shall be installed; or

• (b) if the tools or other objects are piled to such a height that a toe board would not prevent the tools or other objects from falling, a solid or mesh panel shall be installed from the floor to a height of not less than 450 mm.

Housekeeping and Maintenance

• 2.14 (1) Every exterior stairway, walkway, ramp and passageway that may be used by employees shall be kept free of accumulations of ice and snow or other slipping or tripping hazards.

• (2) All dust, dirt, waste and scrap material in every work place in a building shall be removed as often as is necessary to protect the health and safety of employees and shall be disposed of in such a manner that the health and safety of employees is not endangered.

• (3) Every travelled surface in a work place shall be

  • (a) slip resistant; and

  • (b) kept free of splinters, holes, loose boards and tiles and similar defects.

2.15 Where a floor in a work place is normally wet and employees in the work place do not use non-slip waterproof footwear, the floor shall be covered with a dry false floor or platform or treated with a non-slip material or substance.

• 2.16 (1) The cleaning of a window on any level above the ground floor level of a building the construction of which begins on or after the day of the coming into force of this subsection shall be done in accordance with the requirements of CSA Standard CAN/CSA-Z91-M90, entitled Safety Code for Window Cleaning Operations, as amended from time to time.

• (2) To the extent reasonably practicable, the cleaning of a window on any level above the ground floor level of a building the construction of which began before the day of the coming into force of this subsection shall be done in accordance with the requirements referred to in subsection (1).

• (3) Subsections (4) to (8) apply to buildings whose owners are employers as defined in subsection 122(1) of the Act.

• (4) The employer shall, in respect of buildings the construction of which begins on or after the day of the coming into force of this subsection, ensure that a qualified person inspects the anchor points and permanently installed suspended platforms used for window cleaning and that they meet the requirements referred to in subsection (1).

• (5) The employer shall, in respect of buildings the construction of which began before the day of the coming into force of this subsection, ensure that a qualified person inspects the anchor points and permanently installed suspended platforms used for window cleaning and that they meet the requirements of CSA Standard Z91-M1980, entitled Safety Code for Window Cleaning Operations, the English version of which is dated May 1980 and the French version of which is dated November 1983.

• (6) The inspection of anchor points and permanently installed suspended platforms shall be done

  • (a) before they are used for the first time;

  • (b) as often as necessary, but at least as often as recommended by their manufacturer;

  • (c) whenever they are reported as being defective; and

  • (d) in every case, at least once a year.

• (7) Immediately on completion of an inspection, the qualified person shall, in a written, signed and dated report, inform the employer of any defects or hazardous conditions detected in the anchor points or permanently installed suspended platforms.

• (8) The employer shall

  • (a) ensure that any reported defect in the anchor points or permanently installed suspended platforms is repaired before they are used;

  • (b) ensure that any maintenance and repairs are performed in accordance with the manufacturer’s recommendations;

  • (c) keep, for a period of two years, a record of any inspection and maintenance, including the date the inspection or maintenance was carried out and the name of the person who did it; and

  • (d) keep, for as long as the anchor points and permanently installed suspended platforms are used, a record of the modifications or repairs made to them, including the day the work was done and the name of the person who did it.

Temporary Heating

• 2.17 (1) Subject to subsection (2), where a high-capacity portable open-flame heating device is used in an enclosed work place, the heating device shall

  • (a) be located, protected and used so that there is no hazard of igniting tarpaulins, wood or other combustible materials near the heating device;

  • (b) be used only when there is ventilation provided;

  • (c) be located so as to be protected from accidental contact, damage or overturning; and

  • (d) not restrict a means of exit.

• (2) Where the heating device does not provide complete combustion of the fuel used in connection with it, it shall be equipped with an exhaust system that discharges the products of combustion outside the enclosed work place.

DIVISION IITOWERS, ANTENNAS AND ANTENNA-SUPPORTING STRUCTURES

• 2.18 (1) No employee shall climb a tower, an antenna or an antenna-supporting structure unless

  • (a) the employer has authorized the employee to do so;

  • (b) the employee has been trained and instructed in a safe method of climbing; and

  • (c) the employer has provided a fall-protection system in accordance with section 12.10.

• (2) No employee shall climb or work on a tower, an antenna or an antenna-supporting structure

  • (a) when weather conditions are likely to be hazardous to the health or safety of the employee, except when the work is required to remove a hazard or to rescue an employee; or

  • (b) if the physical condition of the tower, antenna or antenna-supporting structure is likely to be hazardous to the health or safety of the employee.

2.19 Where reasonably practicable, the design and construction of every tower, antenna and antenna-supporting structure the construction of which begins on or after the day of the coming into force of this section shall meet the requirements of CSA Standard CAN/CSA-S37-94, entitled Antennas, Towers, and Antenna-Supporting Structures, as amended from time to time.

DIVISION IIIHVAC SYSTEMS

Application

2.20 Sections 2.21 to 2.24 apply to every work place that is equipped with an HVAC system that is under the employer’s control.

Standards

2.21 Subject to section 2.22, every HVAC system installed on or after the day of the coming into force of this section shall meet the design requirements of ASHRAE Standard 62-1989, entitled Ventilation for Acceptable Indoor Air Quality, as amended from time to time.

2.22 To the extent reasonably practicable, the relevant portion of an HVAC system shall be modified to meet the design requirements referred to in section 2.21 if

• (a) the level of occupancy in a building or portion of a building exceeds the level for which the HVAC system was designed; or

• (b) the use of a building or portion of a building differs from the use for which the HVAC system was designed.

Records

• 2.23 (1) For HVAC systems installed on or after the day of the coming into force of this section, the employer shall keep a record of the information required by section A-2.3.5.2 of Appendix A of the National Building Code and make the record readily available.

• (2) In addition to the record required by subsection (1), the employer shall keep and make readily available a record of the normal hours of occupancy and the types of activities of the occupants of the building.

• (3) In the case of HVAC systems to which subsection (1) does not apply, the employer shall keep and make readily available all records required by subsections (1) and (2) that are reasonably practicable to keep.

Operation, Inspection, Testing, Cleaning and Maintenance

• 2.24 (1) Every employer shall appoint a qualified person to set out, in writing, instructions for the operation, inspection, testing, cleaning and maintenance of an HVAC system and the calibration of probes or sensors on which the system relies. In writing the instructions, the qualified person shall take into account CSA Guideline Z204-94, entitled Guideline for Managing Air Quality in Office Buildings, dated June 1994.

• (2) The instructions shall

  • (a) [Repealed, SOR/2011-206, s. 3]

  • (b) be readily available;

  • (c) and (d) [Repealed, SOR/2009-147, s. 3]

  • (e) specify the manner of operation of the HVAC system;

  • (f) specify the nature and frequency of inspections, testing, cleaning and maintenance; and

  • (g) be reviewed by a qualified person and, if necessary, amended

    • (i) when modifications to the HVAC system are carried out in accordance with section 2.22,

    • (ii) when the standard referred to in section 2.21 is amended,

    • (iii) when the an investigation carried out in accordance with section 2.27 has identified that a health or safety hazard exists, or

    • (iv) at least every five years.

• (3) Despite paragraph (2)(c), if an investigation referred to in section 2.27 identifies that a health or safety hazard exists, the instructions shall be developed and made readily available without delay.

• (4) The employer shall appoint a qualified person or persons to implement the instructions and make a report, in writing, of each inspection, testing, cleaning and maintenance operation.

• (5) The report shall be kept readily available by the employer for a period of at least five years and shall

  • (a) specify the date and type of work performed, and the identity of the person who performed it;

  • (b) identify the components of the HVAC system or portion of an HVAC system involved; and

  • (c) record test results, any deficiencies observed and the actions taken to correct them.

2.25 An employer shall ensure that the qualified person or persons referred to in subsection 2.24(4) are instructed and trained in the specific procedures to be followed in the operation, inspection, testing, cleaning and maintenance of the HVAC system and the calibration of probes or sensors on which the system relies.

2.26 An employer shall post, in a place readily accessible to every employee, the telephone number of a contact person to whom health or safety concerns regarding the indoor air quality in the work place can be directed.

Investigations

• 2.27 (1) Every employer shall develop, or appoint a qualified person to develop, a procedure for investigating situations in which the health or safety of an employee in the work place is or may be endangered by the air quality.

• (2) The procedure shall include the following steps:

  • (a) a review of the nature and number of health or safety complaints;

  • (b) a visual inspection of the work place;

  • (c) the inspection of the HVAC system for cleanliness, operation and performance;

  • (d) a review of the maintenance schedule for the HVAC system;

  • (e) the assessment of building use as compared to the use for which it was designed;

  • (f) the assessment of actual level of occupancy as compared to the level for which the building was designed;

  • (g) the determination of potential sources of contaminants;

  • (h) the determination of levels of carbon dioxide, carbon monoxide, temperature, humidity and air motion, where necessary;

  • (i) the specification, where necessary, of tests to be conducted to determine levels of formaldehyde, particulates, airborne fungi and volatile organic compounds; and

  • (j) the identification of the standards or guidelines to be used in evaluating test results.

• (3) In developing the procedure, the employer or the qualified person appointed by the employer shall take into account the Department of Health publication 93-EHD-166, entitled Indoor Air Quality in Office Buildings: A Technical Guide.

• (4) Where the health or safety of an employee in a work place is or may be endangered by the air quality, the employer shall, without delay, appoint a qualified person to carry out an investigation in accordance with the procedure developed pursuant to subsection (1).

• (5) The investigation shall be carried out in consultation with the work place committee or the health and safety representative.

• (6) To the extent reasonably practicable, the employer shall, in consultation with the work place committee or the health and safety representative, remove or control any health or safety hazard that is identified in the course of the investigation.

• (7) Every employer shall keep the records of every indoor air quality complaint and investigation for at least five years.

PART IIITemporary Structures and Excavations

Application

3.1 This Part applies to portable ladders, temporary ramps and stairs, temporary elevated work bases used by employees and temporary elevated platforms used for materials.

General

3.2 No employee shall use a temporary structure where it is reasonably practicable to use a permanent structure.

3.3 No employee shall work on a temporary structure in rain, snow, hail or an electrical or wind storm that is likely to be hazardous to the health or safety of the employee, except if the work is required to remove a hazard or to rescue an employee.

3.4 Tools, equipment and materials used on a temporary structure shall be arranged or secured in such a manner that they cannot be knocked off the structure accidentally.

3.5 No employee shall use a temporary structure unless

• (a) he has authority from his employer to use it; and

• (b) he has been trained and instructed in its safe and proper use.

• 3.6 (1) Prior to a work shift, a qualified person shall make a visual safety inspection of every temporary structure to be used during that shift.

• (2) Where an inspection made in accordance with subsection (1) reveals a defect or condition that adversely affects the structural integrity of a temporary structure, no employee shall use the temporary structure until the defect or condition is remedied.

Barricades

3.7 Where a person or a vehicle may come into contact with a temporary structure, a person shall be positioned at the base of the temporary structure or a highly visible barricade shall be installed around it to prevent any such contact.

Guardrails and Toe Boards

• 3.8 (1) Guardrails and toe boards shall be installed at every open edge of a platform of a temporary structure.

• (2) The guardrails and toe boards referred to in subsection (1) shall meet the standards set out in sections 2.12 and 2.13.

Temporary Stairs, Ramps and Platforms

• 3.9 (1) Subject to subsection 3.10(3), temporary stairs, ramps and platforms shall be designed, constructed and maintained to support any load that is likely to be imposed on them and to allow safe passage of persons and equipment on them.

• (2) Temporary stairs shall have

  • (a) uniform steps in the same flight;

  • (b) a slope not exceeding 1.2 in 1; and

  • (c) a hand-rail that is not less than 900 mm and not more than 1 100 mm above the stair level on open sides including landings.

• (3) Temporary ramps and platforms shall be

  • (a) securely fastened in place;

  • (b) braced if necessary to ensure their stability; and

  • (c) provided with cleats or surfaced in a manner that provides a safe footing for employees.

• (4) A temporary ramp shall be so constructed that its slope does not exceed

  • (a) where the temporary ramp is installed in the stairwell of a building not exceeding two storeys in height, 1 in 1, if cross cleats are provided at regular intervals not exceeding 300 mm; and

  • (b) in any other case, 1 in 3.

Scaffolds

• 3.10 (1) The erection, use, dismantling or removal of a scaffold shall be carried out by or under the supervision of a qualified person.

• (2) The footings and supports of every scaffold shall be capable of carrying, without dangerous settling, all loads that are likely to be imposed on them.

• (3) Every scaffold shall be capable of supporting at least four times the load that is likely to be imposed on it.

• (4) The platform of every scaffold shall be at least 480 mm wide and securely fastened in place.

Portable Ladders

• 3.11 (1) Commercially manufactured portable ladders shall meet the standards set out in CSA Standard CAN3-Z11-M81, Portable Ladders, the English version of which is dated September, 1981, as amended to March, 1983 and the French version of which is dated August, 1982, as amended to June, 1983.

• (2) Subject to subsection (3), every portable ladder shall, while being used,

  • (a) be placed on a firm footing; and

  • (b) be secured in such a manner that it cannot be dislodged accidentally from its position.

• (3) Where, because of the nature of the location or of the work being done, a portable ladder cannot be securely fastened in place, it shall, while being used, be sloped so that the base of the ladder is not less than one-quarter and not more than one-third of the length of the ladder from a point directly below the top of the ladder and at the same level as the base.

• (4) Every portable ladder that provides access from one level to another shall extend at least three rungs above the higher level.

• (5) Metal or wire-bound portable ladders shall not be used where there is a hazard that they may come into contact with any live electrical circuit or equipment.

• (6) No employee shall work from any of the three top rungs of any single or extension portable ladder or from either of the two top steps of any portable step ladder.

Excavation

• 3.12 (1) Before the commencement of work on a tunnel, excavation or trench, the employer shall mark the location of all underground pipes, cables and conduits in the area where the work is to be done.

• (2) Where an excavation or trench constitutes a hazard to employees, a highly visible barricade shall be installed around it.

• (3) In a tunnel or in an excavation or trench that is more than 1.4 m deep and whose sides are sloped at an angle of 45° or more to the horizontal

  • (a) the walls of the tunnel, excavation or trench, and

  • (b) the roof of the tunnel

  shall be supported by shoring and bracing that is installed as the tunnel, excavation or trench is being excavated.

• (4) Subsection (3) does not apply in respect of a trench where the employer provides a system of shoring composed of steel plates and bracing, welded or bolted together, that can support the walls of the trench from the ground level to the trench bottom and can be moved along as work progresses.

• (5) The installation and removal of the shoring and bracing referred to in subsection (3) shall be performed or supervised by a qualified person.

• (6) Tools, machinery, timber, excavated materials or other objects shall not be placed within 1 m from the edge of an excavation or trench.

Safety Nets

• 3.13 (1) Where there is a hazard that tools, equipment or materials may fall onto or from a temporary structure, the employer shall provide a protective structure or a safety net to protect from injury any employee on or below the temporary structure.

• (2) The design, construction and installation of a safety net referred to in subsection (1) shall meet the standards set out in ANSI Standard ANSI A10.11-1979, American National Standard for Safety Nets Used During Construction, Repair and Demolition Operations, dated August 7, 1979.

Housekeeping

3.14 Every platform, hand-rail, guardrail and work area on a temporary structure used by an employee shall be kept free of accumulations of ice and snow while the temporary structure is in use.

3.15 The floor of a temporary structure used by an employee shall be kept free of grease, oil or other slippery substance and of any material or object that may cause an employee to trip.

PART IVElevating Devices

Application

4.1 This Part does not apply to elevating devices used in the underground workings of mines.

Standards

• 4.2 (1) Every elevating device and every safety device attached thereto shall

  • (a) meet the standards set out in the applicable CSA standard referred to in subsection (2) in so far as is reasonably practicable; and

  • (b) be used, operated and maintained in accordance with the standards set out in the applicable CSA standard referred to in subsection (2).

• (2) For the purposes of subsection (1), the applicable CSA standard for

  • (a) elevators, dumbwaiters, escalators and moving walks is CSA Standard CAN3-B44-M85, Safety Code for Elevators, other than clause 9.1.4 thereof, the English version of which is dated November 1985 and the French version of which is dated March 1986;

  • (b) manlifts is CSA Standard B311-M1979, Safety Code for Manlifts, the English version of which is dated October, 1979 and the French version of which is dated July, 1984 and Supplement No. 1-1984 to B311-M1979, the English version of which is dated June, 1984 and the French version of which is dated August, 1984; and

  • (c) elevating devices for the handicapped is CSA Standard CAN3-B355-M81, Safety Code for Elevating Devices for the Handicapped, the English version of which is dated April, 1981 and the French version of which is dated December, 1981.

Use and Operation

4.3 No elevating device shall be used or operated with a load in excess of the load that it was designed and installed to move safely.

• 4.4 (1) Subject to subsection (3), no elevating device shall be used or placed in service while any safety device attached thereto is inoperative.

• (2) Subject to subsection (3), no safety device attached to an elevating device shall be altered, interfered with or rendered inoperative.

• (3) Subsections (1) and (2) do not apply to an elevating device or a safety device that is being inspected, tested, repaired or maintained by a qualified person.

Inspection and Testing

4.5 Every elevating device and every safety device attached thereto shall be inspected and tested by a qualified person to determine that the prescribed standards are met

• (a) before the elevating device and the safety device attached thereto are placed in service;

• (b) after an alteration to the elevating device or a safety device attached thereto; and

• (c) once every 12 months.

• 4.6 (1) A record of each inspection and test made in accordance with section 4.5 shall

  • (a) be signed by the person who made the inspection and test;

  • (b) include the date of the inspection and test and the identification and location of the elevating device and safety device that were inspected and tested; and

  • (c) set out the observations of the person inspecting and testing the elevating device and safety device on the safety of the devices.

• (2) Every record referred to in subsection (1) shall be made by the employer and kept by him in the work place in which the elevating device is located for a period of two years after the date on which it is signed in accordance with paragraph (1)(a).

Repair and Maintenance

4.7 Repair and maintenance of elevating devices or safety devices attached thereto shall be performed by a qualified person appointed by the employer.

PART VBoilers and Pressure Vessels

Interpretation

5.1 The definitions in this section apply in this Part.

Boiler Code

Boiler Code means CSA Standard B51-97, Boiler, Pressure Vessel, and Pressure Piping Code, the English version of which is dated September 1997 and was amended in February 1998 and the French version of which is dated September 1998. (Code des chaudières)

high pressure boiler

high pressure boiler means a boiler in which steam, gas or vapour is generated at more than one atmosphere of pressure or a boiler containing liquid that has a working pressure exceeding 1,100 kPa or an operating temperature exceeding 121°C. (chaudièreà haute pression)

inspector

inspector means a person recognized under the laws of any province or by the National Board of Boiler and Pressure Vessel Inspectors as qualified to inspect boilers, pressure vessels and pressure piping systems. (inspecteur)

low pressure hot water boiler

low pressure hot water boiler means a hot water boiler that has a pressure not exceeding 1,100 kPa and an operating temperature not exceeding 121°C. (chaudière à eau chaude basse pression)

low pressure organic fluid boiler

low pressure organic fluid boiler means a boiler that contains an organic fluid, that has an operating temperature not exceeding 343°C and that has no valves or other obstructions to prevent circulation of the organic fluid between the boiler and an expansion tank that is fully vented to the atmosphere. (chaudière à basse pression contenant un hydrocarbure)

low pressure steam boiler

low pressure steam boiler means a boiler that operates at a vapour pressure not exceeding of one atmosphere of pressure. (chaudière à vapeur basse pression)

low working pressure hot water boiler

low working pressure hot water boiler[Repealed, SOR/2009-147, s. 5]

maximum allowable working pressure

maximum allowable working pressure means the maximum working pressure that is specified by the manufacturer in the plans and specifications accepted and registered by the provincial authorities and that is set out in the record referred to in section 5.18. (pression de fonctionnement maximale autorisée)

maximum temperature

maximum temperature means the maximum temperature that is specified by the manufacturer in the plans and specifications accepted and registered by the provincial authorities and that is set out in the record referred to in section 5.18. (température maximale)

NDT technician

NDT technician means a person who performs nondestructive testing and who is certified to carry out such testing. (technicien END)

pipeline

pipeline has the same meaning as in section 2 of the National Energy Board Act, but does not include boilers. (pipeline)

pressure piping system

pressure piping system means an assembly of pipes, pipe fittings, valves, safety devices, pumps, compressors and other fixed equipment that contains a gas, vapour or liquid and is connected to a boiler or pressure vessel. (réseau de canalisations sous pression)

unfired boiler

unfired boiler means a boiler in which steam or other vapour is generated by a source of heat other than combustion and includes an electric boiler. (chaudière sans combustion)

waste heat boiler

waste heat boiler means an indirect-fired boiler that utilizes waste gases produced by the primary process to generate steam. (chaudière à récupération de chaleur)

Application

5.2 This Part does not apply to

• (a) a heating boiler that has a wetted heating surface of 3 m² or less;

• (b) a pressure vessel that has a capacity of 40 L or less;

• (c) a pressure vessel that is installed for use at a pressure of one atmosphere of pressure or less;

• (d) a pressure vessel that has an internal diameter of 152 mm or less;

• (e) a pressure vessel that has an internal diameter of 610 mm or less and that is used to store hot water;

• (f) a pressure vessel that has an internal diameter of 610 mm or less connected to a water pumping system and that contains compressed air which serves as a cushion;

• (g) a hydropneumatic tank that has an internal diameter of 610 mm or less;

• (h) an interprovincial or international pipeline; or

• (i) a refrigeration plant that has a capacity of 18 kW or less.

Fabrication and Installation Standards

5.3 Every boiler, pressure vessel and pressure piping system used in a work place shall, to the extent reasonably practicable, meet the standards relating to design, construction, testing, stamping, nameplates, fabrication inspection and installation set out in clauses 4.15 to 4.18 and 5.1 to 9.1 of Part 1 of the Boiler Code.

• 5.4 (1) Every boiler and pressure vessel shall have at least one safety valve or other equivalent fitting to maintain pressure at or below the maximum allowable working pressure of the boiler or pressure vessel.

• (2) When two or more boilers or pressure vessels are connected and are used at a common operating pressure, they shall each be fitted with at least one safety valve or other equivalent fitting to maintain pressure at or below the maximum allowable working pressure of the boiler or pressure vessel that has the lowest maximum allowable working pressure.

Use, Operation, Repair, Alteration and Maintenance

• 5.5 (1) An employer shall ensure that a qualified person, charged with the operation of a boiler, is in attendance and readily available at all times while the boiler is in operation and other employees are normally present in the same building as a boiler.

• (2) The attendance referred to in subsection (1) is not required if

  • (a) the boiler is equipped with a fail-safe device and an automated warning device that will ensure the safe operation of the boiler and its shutdown if required, and that are installed in such a manner that they

    • (i) cannot be rendered inoperative, and

    • (ii) can be tested under operating conditions; and

  • (b) the boiler is rated below 2,000 kW in the case of a high pressure boiler, and below 3,000 kW in the case of a low pressure boiler, which includes a low pressure hot water boiler, a low pressure organic fluid boiler and a low pressure steam boiler.

• (3) When a boiler is shut down by a device referred to in paragraph (2)(a), the boiler shall not be restarted unless it has been examined by a qualified person and the cause of the shutdown rectified.

5.6 Every boiler, pressure vessel and pressure piping system in use at a work place shall be operated, maintained and repaired only by a qualified person.

5.7 All repairs and welding of boilers, pressure vessels and pressure piping systems shall be carried out in accordance with the standards referred to in clauses 6.1, 7.1 and 8.1 of Part I of the Boiler Code.

5.8 No person shall alter, interfere with or render inoperative any fitting attached to a boiler or pressure vessel except for the purpose of adjusting or testing the fitting.

• 5.9 (1) The factor of safety of a high pressure lap-seam riveted boiler, shall be increased by at least 0.1 each year after 20 years of use.

• (2) If the boiler is relocated at any time, it shall not be operated at a pressure that is more than one atmosphere of pressure.

Inspections

• 5.10 (1) No person shall use a boiler, pressure vessel or pressure piping system unless it has been inspected by an inspector in accordance with subsection (2) and it has been certified by the inspector as safe for its intended use as stated in the declaration referred to in subparagraph 5.18(2)(b)(v).

• (2) The inspector shall

  • (a) inspect every boiler, pressure vessel and pressure piping system

    • (i) after it is installed and before it is used for the first time,

    • (ii) after any welding, alteration or repair is carried out on it, and

    • (iii) in accordance with section 5.11, 5.12 or 5.16; and

  • (b) make a record of each inspection in accordance with section 5.18.

• (3) A person who operates, repairs or maintains a boiler, pressure vessel or pressure piping system or any part of it may not inspect the boiler, pressure vessel or pressure piping system for the purposes of subsection (2).

• 5.11 (1) Every high pressure boiler and every low pressure steam boiler in use at a work place shall be inspected

  • (a) externally, at least once each year; and

  • (b) internally, at least once every two years.

• (2) Every low pressure hot water boiler and every unfired boiler in use at a work place shall be inspected

  • (a) externally, at least once every two years; and

  • (b) internally, at least once every four years.

• (3) Every low pressure organic fluid boiler in use at a work place shall be inspected

  • (a) externally, at least once every two years; and

  • (b) internally, at least once every three years.

• (4) Every waste heat boiler in use at a work place shall be inspected

  • (a) externally, at least once every year; and

  • (b) internally,

    • (i) at least once every two years, or

    • (ii) where ultrasonic thickness measurements are performed annually by an NDT technician, at least once every three years.

• (5) Pressure vessels, other than buried pressure vessels, that have a corrosion rate exceeding 0.1 mm of metal loss per year shall be inspected

  • (a) externally, at least once every year; and

  • (b) internally,

    • (i) at least once every two years, or

    • (ii) if ultrasonic thickness measurements are performed annually by an NDT technician on representative sections of the pressure vessel, at least once every three years.

• (6) Pressure vessels, other than buried pressure vessels, that have a corrosion not exceeding 0.1 mm of metal loss per year shall be inspected

  • (a) externally, at least once every year; and

  • (b) internally,

    • (i) at least once every four years, or

    • (ii) if ultrasonic thickness measurements are performed annually by an NDT technician on representative sections of the pressure vessel, at least once every six years.

• (7) Air receivers shall be inspected

  • (a) externally, at least once every year; and

  • (b) internally, at least once every five years.

• (8) If the known corrosion rate of a pressure vessel is zero, internal inspection is not necessary provided that complete external inspections, including nondestructive thickness measurements performed by an NDT technician, are made at least once every two years on the pressure vessel and the following conditions are met:

  • (a) the non-corrosive nature of the service conditions, including the effect of trace components, has been established by at least five continuous years of comparable service experience with the fluid being handled;

  • (b) the periodic external inspection indicates that the condition of the pressure vessel does not warrant any further investigation;

  • (c) the operating temperature and pressure of the pressure vessel does not exceed the lower limits for the creep rupture range of the vessel metal; and

  • (d) the pressure vessel is protected against inadvertent contamination, and there is no evidence of contamination.

• (9) If a pressure vessel is used to store anhydrous ammonia, the internal inspection frequency referred to in paragraph (5)(b) may be replaced by an internal inspection conducted at least once every five years if, at the same time, a hydrostatic test at a pressure equal to one and one-half times the maximum allowable working pressure is conducted.

5.12 Every boiler, pressure vessel and pressure piping system in use at a work place shall be inspected by an inspector more frequently than it is provided for in section 5.11, if it is necessary to ensure that the boiler, pressure vessel or pressure piping system is safe for its intended use.

5.13 For the purposes of subsections 5.11(5), (6) and (8), the corrosion rate shall be determined from actual metal loss during the last appropriate inspection period specified in the subsections.

5.14 Stationary or portable air receivers used in the railway industry, instead of being inspected in accordance with subsection 5.11(7) and a record completed in accordance with section 5.18, may be inspected and tested and a record filed in accordance with TC-0-010, Rules for the Installation, Inspection and Testing of Air Reservoirs (Other Than on Motive Power Equipment) made by the Railway Association of Canada and approved by the Minister of Transport on December 5, 1994.

5.15 If a pressure vessel that contains materials hazardous to human health or the environment is to be emptied before being inspected, it shall be emptied and inspected in a manner that does not pose a risk to human health or the environment.

Buried Pressure Vessels

• 5.16 (1) The installation of a buried pressure vessel shall meet the requirements set out in Appendix A to Part I of the Boiler Code.

• (2) Notice of the proposed backfilling shall be given to a health and safety officer at the regional office or district office before backfilling is done over a pressure vessel.

• (3) If test plates are used as an indication of corrosion of a buried pressure vessel, the test plates and, subject to subsection (4), the pressure vessel shall be completely uncovered and inspected by an inspector at least once every three years.

• (4) If, on an inspection referred to in subsection (3), the test plates show no corrosion, the buried pressure vessel may be completely uncovered and inspected at intervals exceeding three years if the employer, immediately after the inspection, notifies in writing a regional health and safety officer at the regional office or district office of the condition of the test plates and of the proposed inspection schedule for the pressure vessel.

• (5) Every buried pressure vessel shall be completely uncovered and inspected at least once every 15 years.

Records and Reports

5.17 The employer shall keep and maintain a record of every boiler, pressure vessel and pressure piping system to which this Part applies and that is under the employer’s control.

• 5.18 (1) A report of each inspection carried out under sections 5.10 to 5.16 shall be completed by the inspector who carried out the inspection.

• (2) Every report referred to in subsection (1)

  • (a) shall be signed by the inspector who carried out the inspection; and

  • (b) shall include

    • (i) the date of the inspection,

    • (ii) the identification and location of the boiler, pressure vessel or pressure piping system that was inspected,

    • (iii) the maximum allowable working pressure and the maximum temperature at which the boiler or pressure vessel may be operated,

    • (iv) a declaration as to whether the boiler, pressure vessel or pressure piping system meets the standards prescribed by this Part,

    • (v) a declaration as to whether the boiler, pressure vessel or pressure piping system is safe for its intended use,

    • (vi) a list of any defects or deficiencies the inspector has observed in the condition or operating and maintenance practices of the boiler, pressure vessel or pressure piping system, and

    • (vii) any other observation that the inspector considers relevant to the safety of employees.

• (3) The employer shall keep readily available every record of inspection for the last two inspection periods and on the request of the work place committee or the health and safety representative, shall provide the work place committee or the health and safety representative with a copy.

PART VILighting

Interpretation

• 6.1 (1) In this Part,

  aerodrome apron

  aerodrome apron means that part of a land aerodrome intended to accommodate the loading and unloading of passengers and cargo and the refuelling, servicing, maintenance and parking of aircraft; (aire de trafic)

  aircraft stand

  aircraft stand means that part of an aerodrome apron intended to be used for the parking of aircraft for the purpose of loading or unloading passengers and providing ground services; (poste de stationnement)

  primary grain elevator

  primary grain elevator means a grain elevator the principal use of which is the receiving of grain directly from producers for storage or forwarding; (installation primaire)

  task position

  task position means a position at which a visual task is performed; (poste de travail)

  VDT

  VDT means a visual display terminal. (TEV)

• (2) For the purposes of this Part, 1 lx is equal to .0929 fc.

Application

6.2 This Part does not apply in respect of lighting in any underground portion of a coal mine.

Measurement of Average Levels of Lighting

6.3 For the purposes of sections 6.4 to 6.10, the average level of lighting at a task position or in an area shall be determined

• (a) by making four measurements at different places representative of the level of lighting at the task position or, in an area, representative of the level of lighting 1 m above the floor of the area; and

• (b) by dividing the aggregate of the results of those measurements by four.

Lighting — Office Areas

6.4 The average level of lighting at a task position or in an area set out in Column I of an item of Schedule I, other than a task position or area referred to in section 6.7 or 6.9, shall not be less than the level set out in Column II of that item.

Lighting — Industrial Areas

6.5 The average level of lighting in an area set out in Column I of an item of Schedule II, other than an area referred to in section 6.7 or 6.9, shall not be less than the level set out in Column II of that item.

Lighting — General Areas

6.6 The average level of lighting in an area set out in Column I of an item of Schedule III, other than an area referred to in section 6.7 or 6.9, shall not be less than the level set out in Column II of that item.

Lighting — VDT

• 6.7 (1) The average level of lighting at a task position or in an area set out in Column I of an item of Schedule IV shall not be more than the level set out in Column II of that item.

• (2) Reflection glare on a VDT screen shall be reduced to the point where an employee at a task position is able to

  • (a) read every portion of any text displayed on the screen; and

  • (b) see every portion of the visual display on the screen.

• (3) Where VDT work requires the reading of a document, supplementary lighting shall be provided where necessary to give a level of lighting of at least 500 lx on the document.

Lighting — Aerodrome Aprons and Aircraft Stands

• 6.8 (1) Subject to subsection (2), the average level of lighting at a task position on an aerodrome apron shall not be less than 10 lx.

• (2) The average level of lighting at a task position on an aircraft stand shall not be less than 20 lx.

Lighting — Artefactual Exhibits and Archival Materials

6.9 The average level of lighting in an area in which artefactual exhibits or archival materials are handled or stored shall not be less than 50 lx.

Emergency Lighting

• 6.10 (1) Emergency lighting shall be provided to illuminate the following areas within buildings:

  • (a) exits and corridors;

  • (b) principal routes providing access to exits in open floor areas; and

  • (c) floor areas where employees normally congregate.

• (2) Except in the case of a primary grain elevator in which hand-held lamps are used for emergency lighting, all emergency lighting provided in accordance with subsection (1) shall

  • (a) operate automatically in the event that the regular power supply to the building is interrupted;

  • (b) provide an average level of lighting of not less than 10 lx; and

  • (c) be independent of the regular power source.

• (3) Where a generator is used as a power source for emergency lighting, the inspection, testing and maintenance of the generator shall be in accordance with the requirements referred to in section 6.7 of the National Fire Code, as amended from time to time.

• (4) Where a central storage battery system is used as a power source for emergency lighting or where emergency lighting is provided by a self-contained emergency lighting unit, the battery system or the unit shall be tested

  • (a) monthly by hand; and

  • (b) annually under simulated power failure or electrical fault conditions.

• (5) Where a battery, other than a hermetically sealed battery, is tested in accordance with paragraph (4)(a), the electrolyte level of the battery shall be checked and, if necessary, adjusted to the proper level.

• (6) Where a self-contained emergency lighting unit is tested in accordance with paragraph (4)(b), all lamps forming part of the unit shall be operated for the time period set out in Sentence 3.2.7.3(2) of the National Building Code, as amended from time to time, that is applicable to the class of buildings to which the building in which the unit is installed belongs.

• (7) Every employer shall make a record of the results of each test performed in accordance with subsection (3) or (4) and keep the record for two years after the test.

Minimum Levels of Lighting

• 6.11 (1) Subject to subsections (2) to (4), the level of lighting at any place at a task position or in an area that may be measured for the purposes of section 6.3 shall not be less than one third of the level of lighting prescribed by this Part for that task position or area.

• (2) The level of lighting at any place at a task position or in an area set out in Column I of item 8 or 9 of Schedule III or Column I of item 1 of Schedule IV that may be measured for the purposes of section 6.3 shall not be less than one tenth of the level of lighting prescribed by this Part for that task position or area.

• (3) The level of lighting at any place at a task position referred to in section 6.8 that may be measured for the purposes of section 6.3 shall not be less than one quarter of the level of lighting prescribed by this Part for that task position.

• (4) In a building the construction of which is commenced after October 31, 1990, the level of emergency lighting at any place in an area referred to in subsection 6.10(1) that may be measured for the purposes of section 6.3 shall not be less than 0.25 lx.

SCHEDULE I(Section 6.4)

Item	Column I	Column II
	Task position or area	Level in lx
1	DESK WORK
	(a) Task positions at which cartography, designing, drafting, plan-reading or other very difficult visual tasks are performed	1 000
	(b) Task positions at which business machines are operated or stenography, accounting, typing, filing, clerking, billing, continuous reading or writing or other difficult visual tasks are performed	500
2	OTHER OFFICE WORK
	Conference and interview rooms, file storage areas, switchboard or reception areas or other areas where ordinary visual tasks are performed	300
3	SERVICE AREAS
	(a) Stairways and corridors that are
	(i) used frequently	100
	(ii) used infrequently	50
	(b) Stairways that are used only in emergencies	30

• SOR/89-515, s. 1

SCHEDULE III(Section 6.6)

Item	Column I	Column II
	Area	Level in lx
1	BUILDING EXTERIORS
	(a) Entrances and exits that are
	(i) used frequently	100
	(ii) used infrequently	50
	(b) Passageways used by persons
	(i) at vehicular intersections	30
	(ii) at other locations	10
	(c) Areas used by persons and mobile equipment in which there is
	(i) a high or moderate level of activity	20
	(ii) a low level of activity	10
	(d) Storage areas in which there is
	(i) a high or moderate level of activity	30
	(ii) a low level of activity	10
2	FIRST AID ROOMS
	(a) in treatment and examination area	1 000
	(b) in other areas	500
3	FOOD PREPARATION AREAS	500
4	PERSONAL SERVICE ROOMS	200
5	BOILER ROOMS	200
6	ROOMS IN WHICH PRINCIPAL HEATING, VENTILATION OR AIR CONDITIONING EQUIPMENT IS INSTALLED	50
7	EMERGENCY SHOWER FACILITIES AND EMERGENCY EQUIPMENT LOCATIONS	50
8	PARKING AREAS
	(a) Covered	50
	(b) Open	10
9	LOBBIES AND ATRIA	100

• SOR/89-515, s. 1
• SOR/96-525, s. 12

PART VIILevels of Sound

Interpretation

7.1 In this Part,

A-weighted sound pressure level

A-weighted sound pressure level means a sound pressure level as determined by a measurement system which includes an A-weighting filter that meets the requirements set out in the International Electrotechnical Commission Standard 651 (1979), Sound Level Meters, as amended from time to time; (niveau de pression acoustique pondérée A)

dBA

dBA means decibel A-weighted and is a unit of A-weighted sound pressure level; (dBA)

large truck

large truck[Repealed, SOR/98-589, s. 1]

noise exposure level (L_ex,8)

noise exposure level (L_ex,8) means 10 times the logarithm to the base 10 of the time integral over any 24 hour period of a squared A-weighted sound pressure divided by 8, the reference sound pressure being 20 µPa; (niveau d’exposition (L_ex,8))

sound level meter

sound level meter means a device for measuring sound pressure level that meets the performance requirements for a Type 2 instrument as specified in the International Electrotechnical Commission Standard 651 (1979), Sound Level Meters, as amended from time to time; (sonomètre)

sound pressure level

sound pressure level means 20 times the logarithm to the base 10 of the ratio of the root mean square pressure of a sound to the reference sound pressure of 20 µPa, expressed in decibels. (niveau de pression acoustique)

Measurement and Calculation of Exposure

• 7.2 (1) For the purposes of this Part, the exposure of an employee to sound shall be measured using an instrument that

  • (a) is recommended for that measurement in clause 4.3 of CSA Standard CAN/CSA-Z107.56-M86, Procedures for the Measurement of Occupational Noise Exposure, as amended from time to time; and

  • (b) meets the requirements for such an instrument set out in clause 4 of the Standard referred to in paragraph (a).

• (2) The exposure of an employee to sound shall be measured in accordance with clauses 5, 6.4.1, 6.4.4, 6.5.2, 6.5.4, 6.6.2 and 6.6.4 of the Standard referred to in paragraph (1)(a).

• (3) For the purposes of this Part, the measurement and calculation of the noise exposure level (L_{ex, 8}) to which an employee is exposed shall take into account the exposure of the employee to A-weighted sound pressure levels of 74 dBA and greater.

• (4) The measurement and calculation of the noise exposure level (L_{ex, 8}) referred to in subsection (3) may also take into account the exposure of the employee to A-weighted sound pressure levels that are less than 74 dBA.

Hazard Investigation

• 7.3 (1) Where an employee in a work place may be exposed to an A-weighted sound pressure level equal to or greater than 84 dBA for a duration that is likely to endanger the employee’s hearing, the employer shall, without delay,

  • (a) appoint a qualified person to carry out an investigation of the degree of exposure; and

  • (b) notify the work place committee or the health and safety representative of the investigation and the name of the person appointed to carry out the investigation.

• (2) [Repealed, SOR/98-589, s. 2]

• (3) For the purposes of subsection (1), the measurement of the A-weighted sound pressure level in a work place shall be performed instantaneously, during normal working conditions, using the slow response setting of a sound level meter.

• (4) In the investigation referred to in subsection (1), the following matters shall be considered:

  • (a) the sources of sound in the work place;

  • (b) the A-weighted sound pressure levels to which the employee is likely to be exposed and the duration of such exposure;

  • (c) the methods being used to reduce this exposure;

  • (d) whether the exposure of the employee is likely to exceed the limits prescribed by section 7.4; and

  • (e) whether the employee is likely to be exposed to a noise exposure level (L_ex,8) equal to or greater than 84 dBA.

• (5) On completion of the investigation and after consultation with the work place committee or the health and safety representative, the person appointed to carry out the investigation shall set out in a written report signed and dated by the person

  • (a) observations respecting the matters considered in accordance with subsection (4);

  • (b) recommendations respecting the measures that should be taken in order to comply with sections 7.4 to 7.8; and

  • (c) recommendations respecting the use of hearing protectors by employees who are exposed to a noise exposure level (L_ex,8) equal to or greater than 84 dBA and not greater than 87 dBA.

• (6) The report shall be kept by the employer at the work place in respect of which it applies for a period of ten years after the date of the report.

• (7) Where it is stated in the report that an employee is likely to be exposed to a noise exposure level (L_ex,8) equal to or greater than 84 dBA, the employer shall, without delay,

  • (a) post and keep posted a copy of the report in a conspicuous place in the work place in respect of which it applies; and

  • (b) provide the employee with written information describing the hazards associated with exposure to high levels of sound.

Limits of Exposure

7.4 No employee in a work place shall, in any 24 hour period, be exposed to

• (a) an A-weighted sound pressure level set out in column I of the schedule for a duration of exposure exceeding the applicable duration set out in column II, or

• (b) a noise exposure level (L_{ex 8}) that exceeds 87 dBA.

Reduction of Sound Exposure

7.5 Insofar as is reasonably practicable, every employer shall, by engineering controls or other physical means other than hearing protectors, reduce the exposure to sound of employees to a level that does not exceed the limits prescribed by section 7.4.

Report to Regional Health and Safety Officer

7.6 Where it is not reasonably practicable, without providing hearing protectors, for an employer to maintain the exposure to sound of an employee to whom section 7.4 applies at a level that does not exceed the limits prescribed by that section, the employer shall, without delay,

• (a) make a report in writing to the regional health and safety officer setting out the reasons why it is not reasonably practicable to do so; and

• (b) provide a copy of the report to the work place committee or the health and safety representative.

Hearing Protection

• 7.7 (1) Where an employer is required to make a report pursuant to section 7.6, the employer shall, as soon as is reasonably practicable, provide every employee whose exposure to sound is likely to exceed the limits prescribed by section 7.4 with a hearing protector that

  • (a) meets the requirements set out in CSA Standard Z94.2-M1984, Hearing Protectors, as amended from time to time; and

  • (b) prevents the employee using the hearing protector from being exposed to a level of sound that exceeds the limits prescribed by section 7.4.

• (2) Where an employer provides a hearing protector to an employee pursuant to subsection (1), the employer shall

  • (a) in consultation with the work place committee or the health and safety representative, formulate a program to train the employee in the fit, care and use of the hearing protector; and

  • (b) implement the program.

• (3) Every employer shall ensure that every person, other than an employee, to whom the employer grants access to a work place where the person is likely to be exposed to a level of sound that exceeds the limits set out in section 7.4 uses a hearing protector that meets the standard referred to in paragraph (1)(a).

Warning Signs

• 7.8 (1) At every work place where an employee may be exposed to an A-weighted sound pressure level greater than 87 dBA, the employer shall, at conspicuous locations within the work place, post and keep posted signs warning of a potentially hazardous level of sound in the work place.

• (2) For the purposes of subsection (1), the measurement of the A-weighted sound pressure level in a work place shall be performed instantaneously, during normal working conditions, using the slow response setting of a sound level meter.

PART VIIIElectrical Safety

Interpretation

8.1 In this Part,

Canadian Electrical Code

Canadian Electrical Code means

• (a) CSA Standard C22.1-1990, Canadian Electrical Code, Part I, dated January 1990, and

• (b) CSA Standard C22.3 No.1-M1979, Overhead Systems and Underground Systems, dated April, 1979; (Code canadien de l’électricité)

control device

control device means a device that will safely disconnect electrical equipment from its source of energy; (dispositif de commande)

electrical equipment

electrical equipment means equipment for the generation, distribution or use of electricity; (outillage électrique)

guarantor

guarantor means a person who gives a guarantee of isolation; (garant)

guarded

guarded means covered, shielded, fenced, enclosed or otherwise protected by means of suitable covers or casings, barriers, guardrails, screens, mats or platforms to remove the possibility of dangerous contact or approach by persons or objects; (protégé)

isolated

isolated means separated or disconnected from every source of electrical, hydraulic, pneumatic or other kind of energy that is capable of making electrical equipment dangerous; (isolé)

person in charge

person in charge means an employee who supervises employees performing work on or a live test of isolated electrical equipment. (responsable)

Application

8.2 This Part does not apply to the underground workings of mines.

Standards

• 8.3 (1) The design, construction and installation of all electrical equipment shall meet the standards set out in the Canadian Electrical Code, Part I, in so far as is reasonably practicable.

• (2) The operation and maintenance of all electrical equipment shall meet the standards set out in the Canadian Electrical Code.

Safety Procedures

• 8.4 (1) All testing or work performed on electrical equipment shall be performed by a qualified person or an employee under the direct supervision of a qualified person.

• (2) Where the electrical equipment has a voltage in excess of 5,200 V between any two conductors or in excess of 3,000 V between any conductor and ground,

  • (a) the qualified person or the employee referred to in subsection (1) shall use such insulated protection equipment and tools as will protect him from injury during the performance of the work; and

  • (b) the employee referred to in subsection (1) shall be instructed and trained in the use of the insulated protection equipment and tools.

• 8.5 (1) Subject to subsections (2) and (3), no employee shall work on electrical equipment unless the equipment is isolated.

• (2) If it is not reasonably practicable to isolate the electrical equipment and an employee must work on live equipment, the employer shall instruct the employee in procedures that are safe for live conductors.

• (3) Where electrical equipment is not live but is capable of becoming live, no employee shall work on the equipment unless

  • (a) procedures that are safe for work on live equipment are used; or

  • (b) a safety ground is connected to the equipment.

• (4) Subject to subsections (5) and (6), where an employee is working on or near electrical equipment that is live or may become live, the electrical equipment shall be guarded.

• (5) Subject to subsection (6), where it is not practicable for the electrical equipment referred to in subsection (4) to be guarded, the employer shall take measures to protect the employee from injury by insulating the equipment from the employee or the employee from ground.

• (6) Where live electrical equipment is not guarded or insulated in accordance with subsection (4) or (5) or where the employee referred to in subsection (5) is not insulated from ground, the employee shall not work so near to any live part of the electrical equipment that is within a voltage range listed in column I of an item of the schedule to this Part that the distance between the body of the employee or any thing with which the employee is in contact and the live part of the equipment is less than

  • (a) the distance set out in column II of that item, where the employee is not a qualified person; or

  • (b) the distance set out in column III of that item, where the employee is a qualified person.

• (7) No employee shall work near a live part of any electrical equipment referred to in subsection (6) where there is a hazard that an unintentional movement by the employee would bring any part of the body of the employee or any thing with which the employee is in contact closer to that live part than the distance referred to in that subsection.

8.6 No employee shall work on or near high voltage electrical equipment unless he is authorized to do so by his employer.

8.7 A legible sign with the words “Danger — High Voltage” and “Danger — Haute Tension” in letters that are not less than 50 mm in height on a contrasting background shall be posted in a conspicuous place at every approach to live high voltage electrical equipment.

Safety Watcher

• 8.8 (1) Where an employee is working on or near live electrical equipment and, because of the nature of the work or the condition or location of the work place, it is necessary for the safety of the employee that the work be observed by a person not engaged in the work, the employer shall appoint a safety watcher

  • (a) to warn all employees in the work place of the hazard; and

  • (b) to ensure that all safety precautions and procedures are complied with.

• (2) A safety watcher shall be

  • (a) informed of his duties as a safety watcher and of the hazard involved in the work;

  • (b) trained and instructed in the procedures to follow in the event of an emergency;

  • (c) authorized to stop immediately any part of the work that he considers dangerous; and

  • (d) free of any other duties that might interfere with his duties as a safety watcher.

• (3) For the purposes of subsection (1), an employer may appoint himself as a safety watcher.

Coordination of Work

8.9 Where an employee is working on or in connection with electrical equipment, that employee and every other person who is so working, including every safety watcher, shall be fully informed by the employer with respect to the safe coordination of their work.

Poles and Elevated Structures

• 8.10 (1) Before an employee climbs a pole or elevated structure that is used to support electrical equipment, the employer shall give instructions and training to the employee respecting inspections and tests of the pole or structure to be carried out before the pole or structure is climbed.

• (2) Where, as a result of an inspection or test of a pole or elevated structure referred to in subsection (1), it appears to an employee that the pole or structure will be safe for climbing only when temporary supports have been installed, pike-poles alone shall not be used for such supports.

• (3) No employee shall work on any pole or elevated structure referred to in subsection (1) unless he has been instructed and trained in the rescue of employees who may be injured in the course of the work.

8.11 Every pole or elevated structure that is embedded in the ground and is used to support electrical equipment shall meet the standards set out in

• (a) CSA Standard CAN3-015-M83, Wood Utility Poles and Reinforcing Studs, dated January, 1983; or

• (b) CSA Standard A14-M1979, Concrete Poles, the English version of which is dated September 1979 and the French version of which is dated November 1987.

Isolation of Electrical Equipment

• 8.12 (1) Before an employee isolates electrical equipment or changes or terminates the isolation of electrical equipment, the employer shall issue written instructions with respect to the procedures to be followed for the safe performance of that work.

• (2) The instructions referred to in subsection (1) shall be signed by the employer and shall specify

  • (a) the date and hour when the instructions are issued;

  • (b) the date and hour of the commencement and of the termination of the period during which the instructions are to be followed;

  • (c) the name of the employee to whom the instructions are issued; and

  • (d) where the instructions are in respect of the operation of a control device that affects the isolation of the electrical equipment,

    • (i) the device to which the instructions apply, and

    • (ii) where applicable, the correct sequence of procedures.

• (3) A copy of the instructions referred to in subsection (1) shall be shown and explained to the employee.

• (4) The instructions referred to in subsection (1) shall be kept readily available for examination by employees for the period referred to in paragraph (2)(b) and thereafter shall be kept by the employer for a period of one year at his place of business nearest to the work place in which the electrical equipment is located.

• 8.13 (1) Subject to subsection (4), no work on or live test of isolated electrical equipment shall be performed unless

  • (a) isolation of the equipment has been confirmed by test; and

  • (b) the employer has determined, on the basis of visual observation, that every control device and every locking device necessary to establish and maintain the isolation of the equipment

    • (i) is set in the safe position with the disconnecting contacts of control devices safely separated or, in the case of a draw-out type electrical switch gear, is withdrawn to its full extent from the contacts of the electrical switch gear,

    • (ii) is locked out, and

    • (iii) bears a distinctive tag or sign designed to notify persons that operation of the control device and movement of the locking device are prohibited during the performance of the work or live test.

• (2) Where more than one employee is performing any work on or live test of isolated electrical equipment, a separate tag or sign for each such employee shall be attached to each control device and locking device referred to in subsection (1).

• (3) The tag or sign referred to in subparagraph (1)(b)(iii) or subsection (2) shall

  • (a) contain the words “DO NOT OPERATE — DÉFENSE D’ACTIONNER” or display a symbol conveying the same meaning;

  • (b) show the date and hour that the control device and the locking device referred to in paragraph (1)(b) were set in the safe position or were withdrawn to their full extent from the contacts;

  • (c) show the name of the employee performing the work or live test;

  • (d) where used in connection with a live test, be distinctively marked as a testing tag or sign;

  • (e) be removed only by the employee performing the work or live test; and

  • (f) be used for no purpose other than the purpose referred to in paragraph (1)(b)(iii).

• (4) Where, because of the nature of the work in which the electrical equipment is being used, it is not practicable to comply with subsection (1), no work on or live test of electrical equipment shall be performed unless a guarantee of isolation referred to in section 8.14 is given to the person in charge.

Guarantees of Isolation for Electrical Equipment

• 8.14 (1) No employee shall give or receive a guarantee of isolation for electrical equipment unless he is authorized in writing by his employer to give or receive a guarantee of isolation.

• (2) Not more than one employee shall give a guarantee of isolation for a piece of electrical equipment for the same period of time.

• (3) Before an employee performs work on or a live test of isolated electrical equipment, the person in charge shall receive from the guarantor

  • (a) a written guarantee of isolation; or

  • (b) where owing to an emergency it is not practicable for the person in charge to receive a written guarantee of isolation, a non-written guarantee of isolation.

• (4) A written guarantee of isolation referred to in paragraph (3)(a) shall be signed by the guarantor and by the person in charge and shall contain the following information:

  • (a) the date and hour when the guarantee of isolation is given to the person in charge;

  • (b) the date and hour when the electrical equipment will become isolated;

  • (c) the date and hour when the isolation will be terminated, if known;

  • (d) the procedures by which isolation is assured;

  • (e) the name of the guarantor and the person in charge; and

  • (f) a statement as to whether live tests are to be performed.

• (5) Where a non-written guarantee of isolation referred to in paragraph (3)(b) is given, a written record thereof shall forthwith

  • (a) be made by the guarantor; and

  • (b) be made and signed by the person in charge.

• (6) A written record referred to in subsection (5) shall contain the information referred to in subsection (4).

• (7) Every written guarantee of isolation and every written record referred to in subsection (5) shall be

  • (a) kept by the person in charge readily available for examination by the employee performing the work or live test until the work or live test is completed;

  • (b) given to the employer when the work or live test is completed; and

  • (c) kept by the employer for a period of one year after the completion of the work or live test at his place of business nearest to the work place in which the electrical equipment is located.

8.15 Where a written guarantee of isolation or a written record of an oral guarantee of isolation is given to a person in charge and the person in charge is replaced at the work place by another person in charge before the guarantee has terminated, the other person in charge shall sign the written guarantee of isolation or written record of the oral guarantee of isolation.

8.16 Before an employee gives a guarantee of isolation for electrical equipment that obtains all or any portion of its electrical energy from a source that is not under his direct control, the employee shall obtain a guarantee of isolation in respect of the source from the person who is in direct control thereof and is authorized to give the guarantee in respect thereof.

Live Test

• 8.17 (1) No employee shall give a guarantee of isolation for the performance of a live test on isolated electrical equipment unless

  • (a) any other guarantee of isolation given in respect of the electrical equipment for any part of the period for which the guarantee of isolation is given is terminated;

  • (b) every person to whom the other guarantee of isolation referred to in paragraph (a) was given has been informed of its termination; and

  • (c) any live test to be performed on the electrical equipment will not be hazardous to the health or safety of the person performing the live test.

• (2) Every person performing a live test shall warn all persons who, during or as a result of the test, are likely to be exposed to a hazard.

Termination of Guarantee of Isolation

• 8.18 (1) Every person in charge shall, when work on or a live test of isolated electrical equipment is completed,

  • (a) inform the guarantor thereof; and

  • (b) make and sign a record in writing containing the date and hour when he so informed the guarantor and the name of the guarantor.

• (2) On receipt of the information referred to in subsection (1), the guarantor shall make and sign a record in writing containing

  • (a) the date and hour when the work or live test was completed; and

  • (b) the name of the person in charge.

• (3) The records referred to in subsections (1) and (2) shall be kept by the employer for a period of one year after the date of signature thereof at his place of business nearest to the work place in which the electrical equipment is located.

Safety Grounding

• 8.19 (1) No employee shall attach a safety ground to electrical equipment unless he has tested the electrical equipment and has established that it is isolated.

• (2) Subsection (1) does not apply in respect of electrical equipment that is grounded by means of a grounding switch that is an integral part of the equipment.

• 8.20 (1) Subject to subsection (2), no work shall be performed on any electrical equipment in an area in which is located

  • (a) a grounding bus,

  • (b) a station grounding network,

  • (c) a neutral conductor,

  • (d) temporary phase grounding, or

  • (e) a metal structure

  unless the equipment referred to in paragraphs (a) to (e) is connected to a common grounding network.

• (2) Where, after the connections referred to in subsection (1) are made, a safety ground is required to ensure the safety of an employee working on the electrical equipment referred to in that subsection, the safety ground shall be connected to the common grounding network.

8.21 Every conducting part of a safety ground on isolated electrical equipment shall have sufficient current carrying capacity to conduct the maximum current that is likely to be carried on any part of the equipment for such time as is necessary to permit operation of any device that is installed on the electrical equipment so that, in the event of a short circuit or other electrical current overload, the electrical equipment is automatically disconnected from its source of electrical energy.

• 8.22 (1) For the purposes of subsection (2), a

  point of safety grounding

  point of safety grounding means

  • (a) a grounding bus, a station grounding network, a neutral conductor, a metal structure or an aerial ground, or

  • (b) one or more metal rods that are not less than 16 mm in diameter and are driven not less than l m into undisturbed compact earth at a minimum distance of 4.5 m from the base of the pole, structure, apparatus or other thing to which the electrical equipment is attached or from the area where persons on the ground work and in a direction away from the main work area. (point de mise à la terre)

• (2) No safety ground shall be attached to or disconnected from isolated electrical equipment except in accordance with the following requirements:

  • (a) the safety ground shall, to the extent that is practicable, be attached to the pole, structure, apparatus or other thing to which the electrical equipment is attached;

  • (b) all isolated conductors, neutral conductors and all non-insulated surfaces of the electrical equipment shall be short-circuited, electrically bonded together and attached by a safety ground to a point of safety grounding in a manner that establishes equal voltage on all surfaces that can be touched by persons who work on the electrical equipment;

  • (c) the safety ground shall be attached by means of mechanical clamps that are tightened securely and are in direct contact with bare metal;

  • (d) the safety ground shall be so secured that none of its parts can make contact accidentally with any live electrical equipment;

  • (e) the safety ground shall be attached and disconnected using insulated protection equipment and tools;

  • (f) the safety ground shall, before it is attached to isolated electrical equipment, be attached to a point of safety grounding; and

  • (g) the safety ground shall, before being disconnected from the point of safety grounding, be removed from the isolated electrical equipment in such a manner that the employee avoids contact with all live conductors.

Switches and Control Devices

• 8.23 (1) Every control device shall be so designed and located as to permit quick and safe operation at all times.

• (2) The path of access to every electrical switch, control device or meter shall be free from obstruction.

• (3) Where an electrical switch or other device controlling the supply of electrical energy to electrical equipment is operated only by a person authorized to do so by the employer, the switch or other device shall be fitted with a locking device that only an authorized person can activate.

SCHEDULE(Subsection 8.5(6))

Item	Column I	Column II	Column III
	Voltage Range of Part: Part to Ground	Distance in metres	Distance in metres
1	Over 425 to 12,000	3	0.9
2	Over 12,000 to 22,000	3	1.2
3	Over 22,000 to 50,000	3	1.5
4	Over 50,000 to 90,000	4.5	1.8
5	Over 90,000 to 120,000	4.5	2.1
6	Over 120,000 to 150,000	6	2.7
7	Over 150,000 to 250,000	6	3.3
8	Over 250,000 to 300,000	7.5	3.9
9	Over 300,000 to 350,000	7.5	4.5
10	Over 350,000 to 400,000	9	5.4

• SOR/98-427, s. 4

PART IXSanitation

Interpretation

9.1 In this Part,

ARI

ARI means the Air-Conditioning and Refrigeration Institute of the United States; (ARI)

Canadian Plumbing Code

Canadian Plumbing Code means the Canadian Plumbing Code, 1985; (Code canadien de la plomberie)

field accommodation

field accommodation means fixed or mobile accommodation that is living, eating or sleeping quarters provided by an employer for the accommodation of employees at a work place; (logement sur place)

mobile accommodation

mobile accommodation means field accommodation that may be easily and quickly moved. (logement mobile)

General

• 9.2 (1) Every employer shall maintain each personal service room and food preparation area used by employees in a clean and sanitary condition.

• (2) Personal service rooms and food preparation areas shall be so used by employees that the rooms or areas will remain as clean and in such a sanitary condition as is possible.

9.3 All janitorial work that may cause dusty or unsanitary conditions shall be carried out in a manner that will prevent the contamination of the air by dust or other substances injurious to health.

9.4 Each personal service room shall be cleaned at least once every day that it is used.

• 9.5 (1) Every plumbing system that supplies potable water and removes water-borne waste

  • (a) shall meet the standards set out in the Canadian Plumbing Code; and

  • (b) subject to subsection (2), shall be connected to a municipal sanitation sewer or water main.

• (2) Where it is not practicable to comply with paragraph (1)(b), the employer shall provide a waste disposal system that meets the standards set out in ANSI standard ANSI Z4.3-1979, Minimum Requirements for Nonsewered Waste-Disposal Systems, dated November 8, 1978.

• 9.6 (1) Each container that is used for solid or liquid waste in the work place shall

  • (a) be equipped with a tight-fitting cover;

  • (b) be so constructed that it can easily be cleaned and maintained in a sanitary condition;

  • (c) be leak-proof; and

  • (d) where there may be internal pressure in the container, be so designed that the pressure is relieved by controlled ventilation.

• (2) Each container referred to in subsection (1) shall be emptied at least once every day that it is used.

• 9.7 (1) Each enclosed part of a work place, each personal service room and each food preparation area shall be constructed, equipped and maintained in a manner that will prevent the entrance of vermin.

• (2) Where vermin have entered any enclosed part of a work place, personal service room or food preparation area, the employer shall immediately take all steps necessary to eliminate the vermin and prevent the re-entry of the vermin.

9.8 No person shall use a personal service room for the purpose of storing equipment unless a closet fitted with a door is provided in that room for that purpose.

9.9 In each personal service room and food preparation area, the temperature, measured one metre above the floor in the centre of the room or area, shall be maintained at a level of not less than 18°C and, where reasonably practicable, not more than 29°C.

• 9.10 (1) In each personal service room and food preparation area, the floors, partitions and walls shall be so constructed that they can be easily washed and maintained in a sanitary condition.

• (2) The floor and lower 150 mm of any walls and partitions in any food preparation area or toilet room shall be water-tight and impervious to moisture.

9.11 Where separate personal service rooms are provided for employees of each sex, each room shall be equipped with a door that is self-closing and is clearly marked to indicate the sex of the employees for whom the room is provided.

Toilet Rooms

• 9.12 (1) Where it is reasonably practicable, a toilet room shall be provided for employees and, subject to section 9.13, where persons of both sexes are employed at the same work place, a separate toilet room shall be provided for employees of each sex.

• (2) Subject to subsections (3) and (4), where a toilet room is provided in accordance with subsection (1), the employer shall provide in that room a number of toilets determined according to the maximum number of employees of each sex who are normally employed by him at any one time at the same work place as follows:

  • (a) where the number of such employees does not exceed nine, one toilet;

  • (b) where the number of such employees exceeds nine but does not exceed 24, two toilets;

  • (c) where the number of such employees exceeds 24 but does not exceed 49, three toilets;

  • (d) where the number of such employees exceeds 49 but does not exceed 74, four toilets;

  • (e) where the number of such employees exceeds 74 but does not exceed 100, five toilets; and

  • (f) where the number of such employees exceeds 100, five toilets and one toilet for every 30 such employees or portion of that number in excess of 100.

• (3) Subject to subsection (4), where the class of employment in a work place is the transaction of business or the rendering of professional or personal services, the number of toilets provided by the employer in accordance with subsection (2) may be reduced

  • (a) where the number of employees of each sex does not exceed 25, to one toilet;

  • (b) where the number of employees of each sex exceeds 25 but does not exceed 50, to two toilets; and

  • (c) where the number of employees of each sex exceeds 50, to three toilets and one toilet for every 50 employees or portion of that number in excess of 50.

• (4) An employer may substitute urinals for up to two-thirds of the number of toilets required by subsection (2) or (3) to be provided for male employees.

• (5) For the purposes of subsections (2) and (3), an employee who is normally away from his work place for more than 75 per cent of his working time and does not normally use the toilet room in the work place shall not be counted.

• (6) Where reasonably practicable, toilet rooms and wash basins separate from those used by other employees shall be provided for food handlers.

• 9.13 (1) Subject to subsection (2), an employer may provide only one toilet for both male and female employees if

  • (a) the total number of employees normally employed by him in the work place at any one time does not exceed five; and

  • (b) the door of the toilet room is fitted on the inside with a locking device.

• (2) Where the class of employment in a work place is the transaction of business or the rendering of professional or personal services, the employer may provide only one toilet for both male and female employees if

  • (a) the total number of employees normally employed by him in the work place at any one time does not exceed 10 or the area of the work place does not exceed 100 m²; and

  • (b) the door of the toilet room is fitted on the inside with a locking device.

9.14 Toilet rooms shall be located not more than 60 m from and not more than one storey above or below each work place.

9.15 Every toilet room shall be so designed that

• (a) it is completely enclosed with solid material that is non-transparent from the outside;

• (b) no toilet or urinal is visible when the door of the toilet room is open;

• (c) it has a ceiling height of not less than 2.2 m;

• (d) where the toilet room contains more than one toilet, each toilet is enclosed in a separate compartment fitted with a door and an inside locking device; and

• (e) the walls of each separate toilet compartment are designed and constructed to provide a reasonable amount of privacy for its occupant.

9.16 Toilet paper on a holder or in a dispenser shall be provided

• (a) where there is only one toilet in a toilet room, in that toilet room; and

• (b) in each toilet compartment.

9.17 A covered container for the disposal of sanitary napkins shall be provided in each toilet room provided for the use of female employees.

Wash Basins

9.18 Hot water provided for personal washing

• (a) shall be maintained at a temperature of not less than 35°C and not more than 43°C; and

• (b) shall not be heated by mixing with steam.

• 9.19 (1) Subject to sections 9.20 and 9.21, every employer shall provide for each toilet room wash basins supplied with cold water and hot water that meets the requirements of section 9.18 as follows:

  • (a) where the room contains one or two toilets or urinals, one wash basin; and

  • (b) where the room contains more than two toilets or urinals, one wash basin for every two toilets or urinals.

• (2) Where an outdoor privy is provided by an employer, the employer shall provide wash basins required by subsection (1) as close to the outdoor privy as is reasonably practicable.

9.20 Subject to section 9.21, where a toilet room is provided and the work environment of employees is such that their health is likely to be endangered by a hazardous substance coming into contact with their skin, the employer shall provide a wash room with individual wash basins supplied with cold water and hot water that meets the requirements of section 9.18 as follows:

• (a) where the number of those employees does not exceed five, one wash basin;

• (b) where the number of those employees exceeds five but does not exceed 10, two wash basins;

• (c) where the number of those employees exceeds 10 but does not exceed 15, three wash basins;

• (d) where the number of those employees exceeds 15 but does not exceed 20, four wash basins; and

• (e) where the number of those employees exceeds 20, four wash basins and one additional wash basin for every 15 of those employees or portion of that number in excess of 20.

• 9.21 (1) An industrial wash trough or circular wash basin of a capacity equivalent to the aggregate of the minimum standard capacities of the wash basins referred to in sections 9.19 and 9.20 may be provided in place of the wash basins.

• (2) An industrial wash trough or circular wash basin referred to in subsection (1) shall be supplied with cold water and hot water that meets the requirements of section 9.18.

9.22 In every personal service room that contains a wash basin, the employer shall provide

• (a) powdered or liquid soap or other cleaning agent in a dispenser at each wash basin or between adjoining wash basins;

• (b) sufficient sanitary hand drying facilities to serve the number of employees using the personal service room; and

• (c) a non-combustible container for the disposal of used towels where towels are provided.

Showers and Shower Rooms

• 9.23 (1) A shower room with a door fitted on the inside with a locking device and at least one shower head for every 10 employees or portion of that number shall be provided for employees who regularly perform strenuous physical work in a high temperature or high humidity or whose bodies may be contaminated by a hazardous substance.

• (2) Every shower receptor shall be constructed and arranged in such a way that water cannot leak through the walls or floors.

• (3) No more than six shower heads shall be served by a single shower drain.

• (4) Where two or more shower heads are served by a shower drain, the floor shall be sloped and the drain so located that water from one head cannot flow over the area that serves another head.

• (5) Except for column showers, where a battery of shower heads is installed, the horizontal distance between two adjacent shower heads shall be at least 750 mm.

• (6) Waterproof finish shall be provided to a height of not less than 1.8 m above the floor in shower rooms and shall consist of ceramic, plastic or metal tile, sheet vinyl, tempered hardboard, laminated thermosetting decorative sheets or linoleum.

• (7) Finished flooring in shower rooms shall consist of resilient flooring, felted-synthetic fibre floor coverings, concrete terrazzo, ceramic tile, mastic or other types of flooring providing similar degrees of water resistance.

• (8) Where duck boards are used in showers, they shall not be made of wood.

• (9) Every shower shall be provided with cold water and hot water that meets the requirements of section 9.18.

• (10) Where an employee referred to in subsection (1) takes a shower as a result of his work, a clean towel and soap or other cleaning agent shall be provided to him.

Potable Water

9.24 Every employer shall provide potable water for drinking, personal washing and food preparation that meets the standards set out in the Guidelines for Canadian Drinking Water Quality 1978, published by authority of the Minister of National Health and Welfare.

9.25 Where it is necessary to transport water for drinking, personal washing or food preparation, only sanitary portable water containers shall be used.

9.26 Where a portable storage container for drinking water is used,

• (a) the container shall be securely covered and closed;

• (b) the container shall be used only for the purpose of storing potable water;

• (c) the container shall not be stored in a toilet room; and

• (d) the water shall be drawn from the container by

  • (i) a tap,

  • (ii) a ladle used only for the purpose of drawing water from the container, or

  • (iii) any other means that precludes the contamination of the water.

9.27 Except where drinking water is supplied by a drinking fountain, sanitary single-use drinking cups shall be provided.

9.28 Any ice that is added to drinking water or used for the contact refrigeration of foodstuffs shall

• (a) be made from potable water; and

• (b) be so stored and handled as to prevent contamination.

9.29 Where drinking water is supplied by a drinking fountain, the fountain shall meet the standards set out in ARI Standard 1010-82, Standard for Drinking-Fountains and Self-Contained, Mechanically-Refrigerated Drinking-Water Coolers, dated 1982.

Field Accommodation

9.30 All field accommodation shall meet the following standards:

• (a) it shall be located on well-drained ground;

• (b) it shall be so constructed that it can easily be cleaned and disinfected;

• (c) the food preparation area and lunch room shall be separated from the sleeping quarters;

• (d) where a water plumbing system is provided, the system shall operate under sanitary conditions;

• (e) garbage disposal facilities shall be provided to prevent the accumulation of garbage;

• (f) toilet rooms shall be maintained in a sanitary condition; and

• (g) vermin prevention, heating, ventilation and sanitary sewage systems shall be provided.

• 9.31 (1) Living quarters provided

  • (a) in any fixed accommodation shall comprise

    • (i) for a single occupant, a space of at least 18 m³, and

    • (ii) where there is more than one occupant, 18 m³ plus 12 m³ for each additional occupant; and

  • (b) in any mobile accommodation shall comprise

    • (i) for a single occupant, a space of at least 12 m³, and

    • (ii) where there is more than one occupant, 12 m³ plus 8 m³ for each additional occupant.

• (2) The living quarters referred to in subsection (1) shall have no floor dimension that is less than 1.5 m.

• (3) Toilet rooms and locker rooms shall not be counted in the calculation made in accordance with subsection (1).

• 9.32 (1) All mobile accommodation shall meet the standards set out in CSA Standard Z240.2.1-1979, Structural Requirements for Mobile Homes, dated September, 1979, as amended to April, 1984.

• (2) For the purposes of clause 4.12.4 of the Standard referred to in subsection (1), there is no other approved method.

9.33 In any field accommodation provided as sleeping quarters for employees

• (a) a separate bed or bunk shall be provided for each employee;

• (b) the beds or bunks shall not be more than double-tiered and shall be so constructed that they can be cleaned and disinfected;

• (c) mattresses, sheets, pillow cases, blankets and bed covers shall be provided for each employee and kept in a clean and sanitary condition;

• (d) clean laundered sheets and pillow cases shall be provided for each employee at least once each week; and

• (e) at least one shelf and a locker fitted with a locking device shall be provided for each employee.

Preparation, Handling, Storage and Serving of Food

• 9.34 (1) Each food handler shall be instructed and trained in food handling practices that prevent the contamination of food.

• (2) No person who is suffering from a communicable disease shall work as a food handler.

9.35 Where food is served in a work place, the employer shall adopt and implement Section G of the Sanitation Code for Canada’s Foodservice Industry published by the Canadian Restaurant and Foodservices Association, dated September, 1984, other than items 2 and 11 thereof.

• 9.36 (1) Where foods stored by an employer for consumption by employees require refrigeration to prevent them from becoming hazardous to health, the foods shall be maintained at a temperature of 4°C or lower.

• (2) Where foods stored by an employer for consumption by employees require freezing to prevent them from becoming hazardous to health, the foods shall be maintained at a temperature of -11°C or lower.

9.37 All equipment and utensils that come into contact with food shall be

• (a) designed to be easily cleaned;

• (b) smooth, free from cracks, crevices, pitting or unnecessary indentations; and

• (c) cleaned to maintain their surfaces in a sanitary condition.

9.38 No person shall eat, prepare or store food

• (a) in a place where a hazardous substance may contaminate food, dishes or utensils;

• (b) in a personal service room that contains a toilet, urinal or shower; or

• (c) in any other place where food is likely to be contaminated.

Food Waste and Garbage

• 9.39 (1) No food waste or garbage shall be stored in a food preparation area.

• (2) Food waste and garbage shall be handled and removed from a food preparation area or lunch room in accordance with subsections (3) to (5).

• (3) Wet food waste and garbage shall be

  • (a) disposed of by mechanical grinders or choppers connected to sewage disposal lines; or

  • (b) held in leak-proof, non-absorptive, easily-cleaned containers with tight-fitting covers in a separate enclosed area or container until removal for disposal.

• (4) Dry food waste and garbage shall be removed or incinerated.

• (5) Food waste and garbage containers shall be kept covered and the food waste and garbage removed as frequently as is necessary to prevent unsanitary conditions.

• (6) Food waste and garbage containers shall, each time they are emptied, be cleansed and disinfected in an area separate from the food preparation area.

Lunch Rooms

9.40 Every lunch room provided by the employer

• (a) shall be separated from any place where a hazardous substance may contaminate food, dishes or utensils;

• (b) shall not be used for any purpose that is incompatible with its use as a lunch room;

• (c) shall not have any dimension of less than 2.3 m;

• (d) shall have a minimum floor area of 9 m²;

• (e) shall have 1.1 m² of floor area for each of the employees who normally use the room at any one time;

• (f) shall be furnished with a sufficient number of tables and seats to accommodate adequately the number of employees normally using the lunch room at any one time; and

• (g) shall be provided with non-combustible covered receptacles for the disposal of waste food or other waste material.

Ventilation

• 9.41 (1) Each personal service room and food preparation area shall be ventilated to provide at least two changes of air per hour

  • (a) by mechanical means, where the room is normally used by 10 or more employees at any one time; or

  • (b) by mechanical means or natural ventilation through a window or similar opening, where the room is used by fewer than 10 employees if

    • (i) the window or similar opening is located on an outside wall of the room, and

    • (ii) not less than 0.2 m² of unobstructed ventilation is provided for each of the employees who normally use the room at any one time.

• (2) Where an employer provides ventilation by mechanical means in accordance with paragraph (1)(a), the amount of air provided for a type of room set out in Column I of an item of the schedule to this Part shall be not less than that set out in Column II of that item.

• (3) Where an employer provides for the ventilation of a food preparation area or a lunch room by mechanical means in accordance with paragraph (1)(a), the rate of change of air shall be not less than nine litres per second for each employee who is normally employed in the food preparation area at any one time or for each employee who uses the lunch room at any one time.

• 9.42 (1) Subject to subsection (2), any exhaust system from a personal service room containing a toilet or a shower shall not be connected with any other exhaust or air supply system.

• (2) The exhaust system for a personal service room containing a toilet or shower may be connected with the exhaust duct of another room at the exhaust fan inlet if the system is connected in such a manner that an exchange of air cannot occur between the rooms.

Clothing Storage

9.43 Clothing storage facilities shall be provided by the employer for the storage of overcoats and outer clothes not worn by employees while they are working.

• 9.44 (1) A change room shall be provided by the employer where

  • (a) the nature of the work engaged in by an employee makes it necessary for that employee to change from street clothes to work clothes for health or safety reasons; or

  • (b) an employee is regularly engaged in work in which his work clothing becomes wet or contaminated by a hazardous substance.

• (2) Where wet or contaminated work clothing referred to in paragraph (1)(b) is changed, it shall be stored in such a manner that it does not come in contact with clothing that is not wet or contaminated.

• (3) No employee shall leave the work place wearing clothing contaminated by a hazardous substance.

• (4) Every employer shall supply drying and cleaning facilities for the purpose of drying or cleaning wet or contaminated clothing referred to in paragraph (1)(b).

• (5) In each change room,

  • (a) a floor area of at least 0.4 m² shall be provided for each of the employees who normally use the room at any one time; and

  • (b) where it is necessary for the employees to change footwear, seats shall be provided in sufficient numbers to accommodate them.

9.45 To the extent that is reasonably practicable, the clothing storage facilities referred to in section 9.43 and the change room referred to in section 9.44 shall be located

• (a) near the work place and connected thereto by a completely covered route;

• (b) on a direct route to the entrance to the work place;

• (c) near a shower room provided pursuant to section 9.23; and

• (d) near a toilet room.

PART XHazardous Substances

Interpretation

10.1 In this Part,

airborne chrysotile asbestos

airborne chrysotile asbestos means airborne fibres longer than 5 micrometers (µm) with an aspect ratio equal to or greater than 3:1; (fibres de chrysotile aéroportées)

hazard information

hazard information, in respect of a hazardous substance, means information on the proper and safe storage, handling, use and disposal of the hazardous substance, including information relating to its toxicological properties; (renseignements sur les risques)

product identifier

product identifier, in respect of a hazardous substance, means the brand name, code name or code number specified by the supplier or employer or the chemical name, common name, generic name or trade name; (identificateur du produit)

readily available

readily available means present in an appropriate place in a physical copy form that can be handled; (facilement accessible)

supplier

supplier means a person who is a manufacturer, processor or packager of a hazardous substance or a person who, in the course of business, imports or sells a hazardous substance. (fournisseur)

Application

10.2 This Part does not apply to the handling or transportation of dangerous goods to which the Transportation of Dangerous Goods Act, 1992 and regulations made thereunder apply.

DIVISION IGENERAL

Records of Hazardous Substances

10.3 Every employer shall keep and maintain a record of all hazardous substances that, in the work place, are used, produced, handled, or stored for use in the work place, and may either keep and maintain such a record in the work place or keep and maintain a centralized record in respect of several work places, in one work place.

Hazard Investigation

• 10.4 (1) If there is a likelihood that the health or safety of an employee in a work place is or may be endangered by exposure to a hazardous substance, the employer shall, without delay,

  • (a) appoint a qualified person to carry out an investigation in that regard; and

  • (b) for the purposes of providing for the participation of the work place committee or the health and safety representative in the investigation, notify either of the proposed investigation and of the name of the qualified person appointed to carry out that investigation.

• (2) In an investigation referred to in subsection (1), the following criteria shall be taken into consideration:

  • (a) the chemical, biological and physical properties of the hazardous substance;

  • (b) the routes of exposure to the hazardous substance;

  • (c) the acute and chronic effects on health of exposure to the hazardous substance;

  • (d) the quantity of the hazardous substance to be handled;

  • (e) the manner in which the hazardous substance is stored, used, handled and disposed of;

  • (f) the control methods used to eliminate or reduce exposure of employees to the hazardous substance;

  • (g) the concentration or level of the hazardous substance to which an employee is likely to be exposed;

  • (h) whether the concentration of an airborne chemical agent or the level of ionizing or non-ionizing radiation is likely to exceed 50 per cent of the values referred to in subsection 10.19(1) or the levels referred to in subsections 10.26(3) and (4); and

  • (i) whether the level referred to in paragraph (g) is likely to exceed or be less than that prescribed in Part VI.

10.5 On completion of an investigation referred to in subsection 10.4(1) and after consultation with the work place committee or the health and safety representative,

• (a) the qualified person shall set out in a written report signed by the qualified person

  • (i) the qualified person’s observations respecting the criteria considered in accordance with subsection 10.4(2), and

  • (ii) the qualified person’s recommendations respecting the manner of compliance with sections 10.7 to 10.26, including recommendations respecting sampling and testing methods; and

• (b) the employer shall develop and maintain a written procedure for the control of the concentration or level of the hazardous substance in the work place.

10.6 A report referred to in section 10.5 shall be kept by the employer for a period of thirty years after the date on which the qualified person signed the report.

Medical Examinations

• 10.7 (1) Where a report referred to in section 10.5 recommends a medical examination for the employees likely to be exposed to a hazardous substance, the employer shall consult a physician to ascertain the necessity for that medical examination.

• (2) The employer, having consulted a physician pursuant to subsection (1) who has confirmed the necessity for a medical examination, shall not permit an employee to handle the hazardous substance in the work place unless a physician acceptable to the employee has examined the employee and declared the employee fit, or fit with specified restrictions, to handle the hazardous substance.

• (3) Where the physician examining an employee pursuant to subsection (2) declares the employee fit with specified restrictions to handle the hazardous substance, the employer shall not permit the employee to handle the hazardous substance in the work place except in accordance with the specified restrictions.

• (4) Where an employer consults a physician pursuant to subsection (1), the employer shall keep a copy of the physician’s decision with the report referred to in section 10.5.

• (5) The cost of a medical examination referred to in subsection (2) shall be borne by the employer.

Storage, Handling and Use

10.8 Every hazardous substance stored, handled or used in a work place shall be stored, handled or used in a manner whereby the hazard related to that substance is reduced to a minimum.

10.9 Where a hazardous substance is stored, handled or used in a work place, any hazard resulting from that storage, handling or use shall be confined to as small an area as is practicable.

10.10 Every container for a hazardous substance that is used in a work place shall be so designed and constructed that it protects the employees from any health or safety hazard that is caused by the hazardous substance.

10.11 The quantity of a hazardous substance for use or processing in a work place shall, to the extent that is practicable, be limited to the quantity required for one work day.

• 10.12 (1) Where, in a work place, a hazardous substance is capable of combining with another substance to form an ignitable combination and there exists a hazard of ignition of the combination by static electricity, the employer shall implement the standards set out in the United States National Fire Protection Association, Inc. publication NFPA 77, Recommended Practice on Static Electricity, dated 1988, as amended from time to time.

• (2) For the purpose of interpreting the standards referred to in subsection (1), acceptable means appropriate.

Warning of Hazardous Substances

10.13 Where a hazardous substance is stored, handled or used in a work place, warnings shall be given in appropriate places at access points warning every person granted access to the work place of the presence of the hazardous substance and of any precautions to be taken to prevent or reduce any hazard of injury to health.

Employee Education

• 10.14 (1) Every employer shall, in consultation with the work place committee or the health and safety representative, develop and implement an employee education program with respect to hazard prevention and control at the work place.

• (2) The employee education program referred to in subsection (1) shall include

  • (a) the instruction of each employee who is likely to handle or be exposed to a hazardous substance with respect to

    • (i) the product identifier of the hazardous substance,

    • (ii) all hazard information disclosed by the supplier or by the employer on a material safety data sheet or label,

    • (iii) all hazard information of which the employer is aware or ought reasonably to be aware,

    • (iv) the observations referred to in subparagraph 10.5(a)(i),

    • (v) the information disclosed on a material safety data sheet referred to in section 10.28 and the purpose and significance of that information, and

    • (vi) in respect of controlled products in the work place, the information required to be disclosed on a material safety data sheet and on a label under Division III and the purpose and significance of that information;

  • (b) the instruction and training of each employee who installs, operates, maintains or repairs an assembly of pipes or any other equipment referred to in section 10.24, with respect to

    • (i) every valve and other control and safety device connected to the assembly of pipes, and

    • (ii) the procedures to follow for the proper and safe use of the assembly of pipes;

  • (c) the instruction and training of each employee referred to in paragraphs (a) and (b) with respect to

    • (i) the procedures to follow to implement sections 10.8, 10.9 and 10.12, and

    • (ii) the procedures to follow for the safe storage, handling, use and disposal of hazardous substances, including procedures to be followed in an emergency involving a hazardous substance; and

  • (d) where the employer keeps a computerized version of a material safety data sheet available in accordance with subsection 10.34(2), the instruction and training referred to in paragraph 10.34(2)(b) in accessing that material safety data sheet.

• (3) Every employer shall, in consultation with the work place committee or the health and safety representative, review the employee education program referred to in subsection (1) and if necessary, revise it

  • (a) at least once a year;

  • (b) whenever there is a change in conditions in respect of the hazardous substances in the work place; and

  • (c) whenever new hazard information in respect of a hazardous substance in the work place becomes available to the employer.

10.15 The employer shall keep a written or computerized record of the instruction and training given to every employee and

• (a) make it readily available for examination by the employee; and

• (b) keep it for a period of two years after the employee ceases

  • (i) to handle or be exposed to the hazardous substance, or

  • (ii) to install, operate, maintain or repair the assembly of pipes.

Substitution of Substances

• 10.16 (1) No person shall use a hazardous substance in a work place where it is reasonably practicable to substitute a substance for it that is not a hazardous substance.

• (2) Where a hazardous substance is to be used for any purpose in a work place and an equivalent substance that is less hazardous is available to be used for that purpose, the equivalent substance shall be substituted for the hazardous substance where reasonably practicable.

Ventilation

• 10.17 (1) Every ventilation system installed on or after January 1, 1997 to control the concentration of an airborne hazardous substance shall be so designed, constructed, installed, operated and maintained that

  • (a) the concentration of the airborne hazardous substance does not exceed the values and levels prescribed in subsections 10.19(1) and 10.20(1) and (2); and

  • (b) it meets the standards set out in

    • (i) Part 6 of the National Building Code,

    • (ii) the publication of the American Conference of Governmental Industrial Hygienists entitled Industrial Ventilation, 20th edition, dated 1988, as amended from time to time, or

    • (iii) ANSI Standard ANSI Z9.2-1979 entitled Fundamentals Governing the Design and Operation of Local Exhaust Systems, dated 1979, as amended from time to time.

• (2) To the extent that is reasonably practicable, every ventilation system installed before January 1, 1997 to control the concentration of an airborne hazardous substance shall be maintained so as to meet the requirements set out in subsection (1).

• 10.18 (1) Before a ventilation system referred to in subsection 10.17(1) is operated for the first time in a work place, the employer shall set out in writing instructions pertaining to the inspection, testing and maintenance of that ventilation system.

• (2) The instructions referred to in subsection (1) shall specify the nature and frequency of inspections, tests and maintenance to be performed on the ventilation system.

• (3) The employer shall ensure that a qualified person

  • (a) carries out each inspection, testing and maintenance of the ventilation system in accordance with the instructions referred to in subsection (1); and

  • (b) makes and signs a report with respect to each inspection, test or maintenance work.

• (4) A report referred to in paragraph (3)(b) shall

  • (a) include the date of the inspection, test or maintenance work performed by the qualified person;

  • (b) identify the ventilation system that was inspected, tested or maintained; and

  • (c) set out the safety observations of the qualified person in respect of the ventilation system.

• (5) The employer shall keep at the work place at which the ventilation system is located a copy of

  • (a) the instructions referred to in subsection (1), and

  • (b) the most recent report referred to in paragraph (3)(b).

• (6) The employer shall give to every operator of a ventilation system the necessary instruction and training for the safe and proper use of the system.

• (7) The employer shall keep a written or computerized record of the instruction and training given to every operator of a ventilation system for as long as the operator remains in the employer’s employ.

Control of Hazards

• 10.19 (1) An employee shall be kept free from exposure to a concentration of

  • (a) an airborne chemical agent, other than grain dust or airborne chrysotile asbestos, in excess of the value for that chemical agent adopted by the American Conference of Governmental Industrial Hygienists, in its publication entitled Threshold Limit Values and Biological Exposure Indices, dated 1994-1995, as amended from time to time;

  • (b) airborne grain dust in excess of 10 mg/m³; or

  • (c) airborne chrysotile asbestos in excess of one fibre per cubic centimetre.

• (2) Subsection (1) does not apply in respect of concentrations of carbon dioxide or respirable dust in the underground portion of a coal mine.

• (3) Where there is a likelihood that the concentration of an airborne chemical agent may exceed the value referred to in subsection (1), air samples shall be taken and the concentration of the chemical agent shall be determined

  • (a) in accordance with the standards set out by the American Conference of Governmental Industrial Hygienists in its publication entitled Manual of Analytical Methods Recommended for Sampling and Analysis of Atmospheric Contaminants, dated 1958, as amended from time to time;

  • (b) in accordance with the standards set out by the United States National Institute for Occupational Safety and Health in the NIOSH Manual of Analytical Methods, third edition, volumes 1 and 2, dated February, 1984, as amended from time to time;

  • (c) in accordance with a method that collects and analyses a representative sample of the chemical agent with accuracy and with detection levels at least equal to those which would be obtained if the standards referred to in paragraph (a) or (b) were used; or

  • (d) where no specific standards for the chemical agent are set out in the publications referred to in paragraphs (a) and (b) and no method is available under paragraph (c), in accordance with a scientifically proven method used to collect and analyse a representative sample of the chemical agent.

• (4) A written or computerized record of each test made pursuant to subsection (3) shall be kept by the employer at the employer’s place of business nearest to the work place where the air sample was taken, for a period of three years after the date of the test.

• (5) A record referred to in subsection (4) shall include

  • (a) the date, time and location of the test;

  • (b) the hazardous substance in respect of which the test was made;

  • (c) the sampling and testing method used;

  • (d) the result obtained; and

  • (e) the name and occupation of the person who made the test.

• 10.20 (1) Subject to subsection (2), the concentration of an airborne chemical agent or combination of airborne chemical agents in the work place shall be less than 50 per cent of the lower explosive limit of the chemical agent or combination of chemical agents.

• (2) Where a source of ignition may ignite an airborne chemical agent or combination of airborne chemical agents in the work place, the maximum concentration of the chemical agent or of the combination of chemical agents shall be 10 per cent of the lower explosive limit of the chemical agent or combination of chemical agents.

• (3) Subsection (2) does not apply in respect of concentrations of methane gas in the underground portion of a coal mine.

• 10.21 (1) Compressed air, gas or steam shall not be used for blowing dust or other substances from structures, machinery or materials where

  • (a) there is a risk of any person being directly exposed to the jet or where a fire, explosion, injury or health hazard is likely to result from such use; or

  • (b) such use would result in a concentration of an airborne hazardous substance in excess of the values referred to in paragraphs 10.19(1)(a) and (c) or the limits referred to in subsections 10.20(1) and (2).

• 10.22 (1) Compressed air shall not be used for cleaning clothing contaminated with:

  • (a) asbestos; or

  • (b) a hazardous substance having an exposure limit referred to in paragraph 10.19(1)(a) or (b) lower than 1 mg/m³.

• (2) Where compressed air is used to clean clothing,

  • (a) appropriate eye protection shall be worn; and

  • (b) the maximum compressed air pressure in the pipeline shall be 69 kPa (10 psi) or a safety nozzle limiting the air pressure to no more than 69kPa (10 psi) shall be used.

Warnings

10.23 Where reasonably practicable, the employer shall provide automated warning and detection systems where the seriousness of any exposure to a hazardous substance so requires.

Assembly of Pipes

10.24 Every assembly of pipes, pipe fittings, valves, safety devices, pumps, compressors and other fixed equipment that is used for transferring a hazardous substance from one location to another shall be

• (a) labelled to identify the hazardous substance transferred therein and, where appropriate, the direction of the flow; and

• (b) fitted with valves and other control and safety devices to ensure its safe operation, maintenance and repair.

Explosives

10.25 All blasting using dynamite or other explosives shall be done by a qualified person who, where required under the laws of the province in which the blasting is carried out, holds a blasting certificate or such other authorization as may be required under those laws.

Ionizing and Non-ionizing Radiation

• 10.26 (1) Where a device that is capable of producing and emitting energy in the form of ionizing or non-ionizing radiation is used in the work place, the employer shall

  • (a) if the device is listed in the schedule to this Division, make a report in writing to the Consumer and Clinical Radiation Protection Bureau of the Department of Health, setting out a description of the device and the location of the work place; and

  • (b) if the device is referred to in subsection (2), implement the applicable document, as amended from time to time, published by the Department of National Health and Welfare, as specified in one of paragraphs (2)(a) to (k) or published by ANSI, as specified in paragraph (2)(l).

• (2) For the purposes of paragraph (1)(b), the applicable document is

  • (a) in respect of radio frequency and microwave devices in the frequency range from 10 kHz to 300 GHz, Safety Code - 6, dated 1990;

  • (b) in respect of X-ray equipment in medical diagnosis, Safety Code - 20A, dated 1980;

  • (c) in respect of baggage inspection X-ray equipment, Safety Code - 21, dated 1978;

  • (d) in respect of dental X-ray equipment, Safety Code - 22, dated 1980;

  • (e) in respect of ultrasound equipment, Safety Code - 23, dated 1989, and Safety Code - 24, dated 1990;

  • (f) in respect of short-wave diathermy equipment, Safety Code - 25, dated 1983;

  • (g) in respect of magnetic resonance imaging and magnetic resonance spectroscopy equipment, Safety Code - 26, dated 1987;

  • (h) in respect of industrial X-ray equipment, Safety Code - 27, dated 1987;

  • (i) in respect of veterinary X-ray equipment, Safety Code - 28, dated 1991;

  • (j) in respect of demonstration-type discharge devices, Recommended Safety Procedures for the Selection and Use of Demonstration-Type Discharge Devices in Schools, dated 1979;

  • (k) in respect of dielectric (RF) heaters, Dielectric (RF) Heaters Guidelines for Limiting Radio-Frequency Exposure, dated 1980; and

  • (l) in respect of lasers, ANSI Standard ANSI Z136.1-1986, American National Standard for the Safe Use of Lasers, dated 1986, including its appendices with the exception of Appendix D.

• (3) If an employee works on or near a device that may emit nuclear energy, the employer shall ensure that the exposure of the employee to nuclear energy does not exceed the radiation dose limits set out in the Radiation Protection Regulations.

• (4) No employee, other than a nuclear energy worker as defined in section 2 of the Nuclear Safety and Control Act, shall be exposed in the course of any year to a concentration of radon that on average, over the year, is higher than 800 Bq/m³.

DIVISION IIHAZARDOUS SUBSTANCES OTHER THAN CONTROLLED PRODUCTS

Identification

10.27 Every container of a hazardous substance, other than a controlled product, that is stored, handled, used or disposed of in the work place shall be labelled in a manner that discloses clearly

• (a) the generic name of the substance; and

• (b) the hazard information in respect of the substance.

10.28 Where a material safety data sheet in respect of a hazardous substance, other than a controlled product, that is stored, handled or used in the work place may be obtained from the supplier of the hazardous substance, the employer shall

• (a) obtain a copy of the material safety data sheet; and

• (b) keep a copy of the material safety data sheet readily available in the work place for examination by employees.

DIVISION IIICONTROLLED PRODUCTS

Interpretation

10.29 In this Division,

bulk shipment

bulk shipment means a shipment of a controlled product that is contained, without an intermediate container or intermediate packaging, in

• (a) a tank with a water capacity of more than 454 L,

• (b) a freight container or a portable tank,

• (c) a road vehicle, railway vehicle or ship, or

• (d) a pipeline; (expédition en vrac)

fugitive emission

fugitive emission means a controlled product in gas, liquid or solid form that escapes from processing equipment, from control emission equipment or from a product; (émission fugitive)

hazardous waste

hazardous waste means a controlled product that is intended solely for disposal or is sold for recycling or recovery; (résidu dangereux)

laboratory sample

laboratory sample, in respect of a controlled product, means a sample of the controlled product that is intended solely to be tested in a laboratory, but does not include a controlled product that is to be used

• (a) by the laboratory for testing other products, materials or substances, or

• (b) for educational or demonstration purposes; (échantillon pour laboratoire)

manufactured article

manufactured article means any article that is formed to a specific shape or design during manufacture, the intended use of which when in that form is dependent in whole or in part on its shape or design, and that, under normal conditions of use, will not release or otherwise cause a person to be exposed to a controlled product; (article manufacturé)

research and development

research and development, in respect of a controlled product, means systematic investigation or search carried out in a field of science or technology by means of experiment or analysis, other than investigation or search in respect of market research, sales promotion, quality control or routine testing of controlled products, and includes

• (a) applied research, namely, work undertaken for the advancement of scientific knowledge with a specific practical application in view, and

• (b) development, namely, use of the results of applied research for the purpose of creating new, or improving existing, processes or controlled products; (recherche et développement)

risk phrase

risk phrase, in respect of a controlled product, means a statement identifying a hazard that may arise from the exposure to the controlled product; (mention de risque)

sale

sale includes offer for sale, expose for sale and distribute; (vente)

supplier label

supplier label, in respect of a controlled product, means a label prepared by a supplier pursuant to the Hazardous Products Act; (étiquette du fournisseur)

supplier material safety data sheet

supplier material safety data sheet, in respect of a controlled product, means a material safety data sheet prepared by a supplier pursuant to the Hazardous Products Act; (fiche signalétique du fournisseur)

work place label

work place label, in respect of a controlled product, means a label prepared by an employer pursuant to this Division; (étiquette du lieu de travail)

work place material safety data sheet

work place material safety data sheet, in respect of a controlled product, means a material safety data sheet prepared by an employer pursuant to subsection 10.33(1) or (2). (fiche signalétique du lieu de travail)

Application

• 10.30 (1) This Division does not apply in respect of any

  • (a) wood or product made of wood;

  • (b) tobacco or product made of tobacco; or

  • (c) manufactured article.

• (2) This Division, other than section 10.43, does not apply in respect of hazardous waste.

Material Safety Data Sheets and Labels in respect of Certain Controlled Products

• 10.31 (1) Subject to subsection (2) and section 10.42, every employer shall implement the provisions of sections 10.27 and 10.28 in respect of a controlled product and may, in so doing, replace the generic name of the substance with the product identifier, where the controlled product is a controlled product that

  • (a) is present in the work place;

  • (b) was received from a supplier; and

  • (c) is one of the following:

    • (i) an explosive within the meaning of section 2 of the Explosives Act,

    • (ii) a cosmetic, device, drug or food within the meaning of section 2 of the Food and Drugs Act,

    • (iii) a control product within the meaning of section 2 of the Pest Control Products Act,

    • (iv) a nuclear substance, within the meaning of section 2 of the Nuclear Safety and Control Act, that is radioactive, and

    • (v) a product, material or substance included in Part II of Schedule I to the Hazardous Products Act that is packaged as a consumer product.

• (2) An employer may store a controlled product received from a supplier without having a supplier label on it, without having obtained a material safety data sheet for it and without having conducted a program of employee education with respect to the matters referred to in subparagraphs 10.14(2)(a)(ii) and (c)(ii)

  • (a) while the employer is actively seeking a supplier label and a supplier material safety data sheet for the controlled product; and

  • (b) if labelling affixed to the container of the controlled product containing information on the controlled product is not removed, defaced, modified or altered.

Supplier Material Safety Data Sheets

• 10.32 (1) Where a controlled product, other than a controlled product referred to in paragraph 10.31(1)(c), is received in the work place by an employer, the employer shall, without delay, obtain from the supplier of the controlled product a supplier material safety data sheet in respect of the controlled product, unless the employer is in possession of a supplier material safety data sheet that

  • (a) is for a controlled product that has the same product identifier;

  • (b) discloses information that is current at the time that the controlled product is received; and

  • (c) was prepared and dated not more than three years before the date that the controlled product is received.

• (2) Where there is a controlled product in a work place and the supplier material safety data sheet in respect of the controlled product is three years old or more, the employer shall, where possible, obtain from the supplier an up-to-date supplier material safety data sheet.

• (3) Where it is not practicable for an employer to obtain an up-to-date supplier material safety data sheet, the employer shall update the hazard information on the most recent supplier material safety data sheet that the employer has received on the basis of the ingredients disclosed on that supplier material safety data sheet.

• (4) Where a controlled product is received in a work place that is a laboratory, from a supplier who is exempted by the Controlled Products Regulations from the requirement to provide a material safety data sheet for that product, the employer is exempt from the requirements of subsection (1) if the controlled product

  • (a) originates from a laboratory supply house;

  • (b) is intended for use in a laboratory; and

  • (c) is packaged in a container in a quantity of less than 10 kg.

Work Place Material Safety Data Sheets

• 10.33 (1) Subject to section 10.42, where an employer produces a controlled product, other than a fugitive emission, in the work place or imports into Canada a controlled product and brings it into the work place, the employer shall prepare a work place material safety data sheet in respect of the controlled product that discloses the information required to be disclosed by

  • (a) paragraph 125.1(e) of the Act; and

  • (b) the Controlled Products Regulations.

• (2) Subject to section 10.42, where an employer receives a supplier material safety data sheet, the employer may prepare a work place material safety data sheet to be used in the work place in place of the supplier material safety data sheet if

  • (a) the work place material safety data sheet discloses at least the information disclosed on the supplier material safety data sheet;

  • (b) the information disclosed on the work place material safety data sheet does not disclaim or contradict the information disclosed on the supplier material safety data sheet;

  • (c) the supplier material safety data sheet is readily available for examination by employees in the work place; and

  • (d) the work place material safety data sheet discloses that the supplier material safety data sheet is available in the work place.

• (3) Where an employer produces, in a work place that is a laboratory supply house, or imports into Canada and brings it into such a work place, a controlled product that is intended for use in a laboratory, the employer is exempted from the requirements of subsection (1) if the employer

  • (a) packages the controlled product in containers in quantities of less than 10 kg per container; and

  • (b) subject to section 10.42, discloses on the label of the container of the controlled product the information required to be disclosed by

    • (i) paragraph 125.1(e) of the Act, and

    • (ii) section 10.39.

• (4) The employer shall update a work place material safety data sheet referred to in subsection (1) or (2) or a label referred to in paragraph (3)(b)

  • (a) as soon as practicable but not later than 90 days after new hazard information becomes available to the employer; and

  • (b) at least once every three years.

• (5) Where the information required to be disclosed by this section is not available or not applicable to the controlled product, the employer shall replace the information with the words “not available” or “not applicable”, as the case may be, in the English version and the words “pas disponible” or “sans objet”, as the case may be, in the French version of the work place material safety data sheet.

Availability of Material Safety Data Sheets

• 10.34 (1) Subject to subsection (2), every employer, other than an employer referred to in subsection 10.32(4), shall keep readily available for examination by employees and by the work place committee or the health and safety representative in any work place in which an employee may handle or be exposed to a controlled product, a copy in English and in French of

  • (a) in the case of an employer who is an employer referred to in subsection 10.33(1) or (2), the work place material safety data sheet; and

  • (b) in any other case, the supplier material safety data sheet.

• (2) In place of keeping a material safety data sheet in the manner required by subsection (1), an employer may keep a computerized version of the material safety data sheet available in English and in French, for examination by employees and by the work place committee or the health and safety representative, by means of a computer terminal, if the employer

  • (a) takes all reasonable steps to maintain the terminal in working order;

  • (b) provides the instruction and training referred to in paragraph 10.14(2)(d) to one or more employees on each shift and to all members of the work place committee or the health and safety representative; and

  • (c) on the request of an employee, the work place committee or the health and safety representative, makes the material safety data sheet readily available to the employee, the work place committee or the health and safety representative.

Labels

• 10.35 (1) Subject to sections 10.37 to 10.39, each controlled product, other than a controlled product referred to in paragraph 10.31(1)(c), in a work place and each container in which the controlled product is contained in a work place shall, if the controlled product or the container is received from a supplier,

  • (a) in the case where the controlled product is in a bulk shipment, be accompanied by a supplier label;

  • (b) in the case where the employer has undertaken in writing to apply a label to the inner container of the controlled product, have applied to it a supplier label, as soon as possible after the controlled product is received from the supplier; and

  • (c) in any other case, have applied to it a supplier label.

• (2) Subject to sections 10.37 to 10.39 and 10.42, where a controlled product, other than a controlled product referred to in paragraph 10.31(1)(c), is received from a supplier and an employer places the controlled product in the work place in a container, other than the container in which it was received from the supplier, the employer shall apply to the container a supplier label or a work place label that discloses the information referred to in paragraphs 10.41(a) to (c).

• (3) Subject to sections 10.41 and 10.42, no person shall remove, deface, modify or alter the supplier label applied to

  • (a) a controlled product that is in the work place; or

  • (b) the container of a controlled product that is in the work place.

• 10.36 (1) Subject to sections 10.37 to 10.39, where an employer produces a controlled product in a work place, other than a fugitive emission, or imports into Canada and brings into a work place, a controlled product, and the controlled product is not in a container, the employer shall disclose the following information on a work place label applied to the controlled product or on a sign posted in a conspicuous place in the work place:

  • (a) the product identifier;

  • (b) the hazard information in respect of the controlled product; and

  • (c) a statement indicating that a work place material safety data sheet for the controlled product is available in the work place.

• (2) Subject to sections 10.37 and 10.39, where an employer produces a controlled product in the work place, other than a fugitive emission, or imports into Canada and brings into the work place a controlled product, and places the controlled product in a container, the employer shall apply to the container a work place label that discloses the information referred to in paragraphs (1)(a) to (c).

• (3) Subsection (2) does not apply in respect of a controlled product that is

  • (a) intended for export, if the information referred to in paragraphs (1)(a) to (c) is disclosed on a sign posted in a conspicuous place in the work place; or

  • (b) packaged in a container and offered for sale in Canada, if the container is or is in the process of being appropriately labelled for that purpose.

Portable Containers

10.37 Where an employer stores a controlled product in the work place in a container that has applied to it a supplier label or a work place label, a portable container filled from that container is exempted from the labelling requirements under section 10.35 or 10.36 if

• (a) the controlled product is required for immediate use; or

• (b) the following conditions apply in respect of the controlled product:

  • (i) it is under the control of and used exclusively by the employee who filled the portable container,

  • (ii) it is used only during the work shift in which the portable container was filled, and

  • (iii) it is clearly identified by a work place label applied to the portable container that discloses the product identifier.

Special Cases

10.38 An employer shall, in a conspicuous place near a controlled product, post a sign in respect of the controlled product that discloses the product identifier if the controlled product is

• (a) in a process, reaction or storage vessel;

• (b) in a continuous-run container;

• (c) in a bulk shipment that is not placed in a container at the work place; or

• (d) not in a container and stored in bulk.

Laboratories

• 10.39 (1) Subject to subsection (2), the label of the container of a controlled product in a laboratory shall disclose

  • (a) where the controlled product is used exclusively in the laboratory, the product identifier;

  • (b) where the controlled product is a mixture or substance intended solely for analysis, testing or evaluation for research and development, the product identifier; and

  • (c) where the controlled product originates from a laboratory supply house and is received in a container in a quantity of less than 10 kg, the following information:

    • (i) the product identifier,

    • (ii) where a material safety data sheet is available, a statement to that effect,

    • (iii) risk phrases that are appropriate to the controlled product,

    • (iv) precautionary measures to be followed when handling, using or being exposed to the controlled product, and

    • (v) where appropriate, first aid measures to be taken in case of exposure to the controlled product.

• (2) No supplier label is required on a sample of a product received from a supplier that is, or the employer has reason to believe may be, a controlled product, if

  • (a) the controlled product is

    • (i) in a container in a quantity of less than 10 kg,

    • (ii) intended by the employer for use solely for analysis, testing or evaluation in a laboratory, and

    • (iii) one in respect of which the supplier is exempted by section 9 of the Controlled Products Regulations from the requirement to provide a material safety data sheet; and

  • (b) the supplier provides a label that is to be affixed to the container of the controlled product disclosing the information described in subsection (3).

• (3) A label referred to in paragraph (2)(b) shall disclose, in respect of the controlled product,

  • (a) the product identifier;

  • (b) the chemical identity or generic chemical identity of every ingredient of the controlled product referred to in any of subparagraphs 13(a)(i) to (iv) of the Hazardous Products Act, if known to the supplier;

  • (c) the supplier identity;

  • (d) the statement “Hazardous Laboratory Sample. For hazard information or in an emergency call (number disclosed pursuant to paragraph (e))/Échantillon pour laboratoire d’un produit dangereux. Pour obtenir des renseignements sur les risques ou en cas d’urgence, composer (le numéro indiqué conformément à l’alinéa e))”; and

  • (e) an emergency telephone number of the supplier that enables

    • (i) a user of the controlled product to obtain the hazard information in respect of the controlled product, and

    • (ii) a medical professional to obtain the information in respect of the controlled product that is referred to in paragraph 13(a) of the Hazardous Products Act.

• (4) Where a controlled product is in a container other than the container in which it was received from a supplier, or is produced in the work place, the employer is exempt from the requirements of section 10.36 and subparagraph 10.37(b)(iii) if

  • (a) the employer has complied with subsection (5);

  • (b) employee education is provided as required by these Regulations; and

  • (c) the controlled product

    • (i) originates from a laboratory supply house or is a laboratory sample,

    • (ii) is intended by the employer solely for analysis, testing or evaluation in a laboratory, and

    • (iii) is clearly identified through any mode of identification visible to employees at the work place.

• (5) For the purposes of paragraph (4)(a), the employer shall ensure that the mode of identification used and the employee education enable the employees to readily identify and obtain either the information required on a material safety data sheet or the information referred to in subsection (3) with respect to the controlled product or laboratory sample.

Signs

10.40 The information disclosed on a sign referred to in subsection 10.36(1), paragraph 10.36(3)(a), section 10.38 or paragraph 10.43(b) shall be of such a size that it is clearly legible to employees.

Replacing Labels

10.41 Where, in a work place, a label applied to a controlled product or a container of a controlled product becomes illegible or is removed from the controlled product or the container, the employer shall replace the label with a work place label that discloses the following information in respect of the controlled product:

• (a) the product identifier;

• (b) the hazard information; and

• (c) a statement indicating that a material safety data sheet is available in the work place.

Exemptions from Disclosure

• 10.42 (1) Subject to subsection (2), where an employer has filed a claim for exemption from disclosure of information on a material safety data sheet or on a label pursuant to subsection 11(2) of the Hazardous Materials Information Review Act, the employer shall disclose, in place of the information that the employer is exempt from disclosing,

  • (a) where there is no final disposition of the proceedings in relation to the claim, the date on which the claim for exemption was registered and the registry number assigned to the claim under that Act; and

  • (b) where the final disposition of the proceedings in relation to the claim is that the claim is valid, a statement that an exemption has been granted and the date on which the exemption was granted.

• (2) Where a claim for exemption is in respect of the chemical name, common name, generic name, trade name or brand name of a controlled product, the employer shall, on the material safety data sheet or label of the controlled product, replace that name with a code name or code number specified by the employer as the product identifier for that controlled product.

Hazardous Waste

10.43 Where a controlled product in a work place is hazardous waste, the employer shall disclose the generic name and hazard information in respect of the controlled product by

• (a) applying a label to the hazardous waste or its container; or

• (b) posting a sign in a conspicuous place near the hazardous waste or its container.

Information Required in a Medical Emergency

10.44 For the purposes of subsection 125.2(1) of the Act, a medical professional is a registered nurse registered or licensed under the laws of a province.

Fire and Explosion Prevention

• 10.45 (1) [Repealed, SOR/98-427, s. 9]

• (2) For the purpose of interpreting the standards referred to in sections 10.46 to 10.49,

  • (a) [Repealed, SOR/2000-374, s. 4]

  • (b) dangerous goods means controlled products used in these Regulations; and

  • (c) in respect of a controlled product classified under the Controlled Products Regulations,

    • (i) flammable liquids means flammable liquids used in these Regulations,

    • (ii) combustible liquids means combustible liquids used in these Regulations,

    • (iii) compressed gases means compressed gases used in these Regulations,

    • (iv) reactive substances means reactive flammable materials used in these Regulations,

    • (v) aerosol products means flammable aerosols used in these Regulations,

    • (vi) poisonous and infectious substances means poisonous and infectious materials used in these Regulations,

    • (vii) corrosive substances" means corrosive materials used in these Regulations, and

    • (viii) oxidizing substances means oxidizing materials used in these Regulations.

10.46 Controlled products shall be stored in accordance with subsections 3.2.7, 3.2.8, 3.2.9 and 3.3.4 of the National Fire Code.

10.47 Flammable aerosols shall be stored in accordance with subsection 3.2.5 of the National Fire Code.

10.48 The provisions of Part 3 of the National Fire Code apply as follows:

• (a) compressed gases shall be stored and handled in accordance with subsections 3.2.8 and 3.3.5;

• (b) reactive flammable materials shall be stored and handled in accordance with subsections 3.2.7 and 3.3.4;

• (c) poisonous and infectious materials shall be stored and handled in accordance with subsections 3.2.7, 3.2.8 and 3.3.4;

• (d) corrosive materials shall be stored and handled in accordance with subsections 3.2.7, 3.2.8 and 3.3.4; and

• (e) oxidizing materials shall be stored and handled in accordance with subsections 3.2.7, 3.2.8 and 3.3.4.

10.49 The provisions of Part 4 of the National Fire Code apply as follows:

• (a) areas used for the storage, handling and use of flammable liquids and combustible liquids shall meet the standards set out in subsection 4.1.5, with the exception of article 4.1.5.6;

• (b) the drainage and disposal of flammable liquids and combustible liquids shall be in accordance with subsection 4.1.6;

• (c) flammable liquids and combustible liquids shall be stored in storage tanks meeting the standards set out in subsection 4.1.8;

• (d) maintenance and operating procedures shall be established to prevent the escape of flammable liquids and combustible liquids, as required by subsection 4.1.6;

• (e) general container storage and handling of flammable liquids and combustible liquids shall be in accordance with subsections 4.2.1 to 4.2.8, with the exception of paragraph 4.2.8.4(d);

• (f) rooms used for container storage of flammable liquids and combustible liquids shall conform with subsection 4.2.9, with the exception of article 4.2.9.3;

• (g) cabinets used for container storage of flammable liquids and combustible liquids shall conform with subsection 4.2.10;

• (h) outdoor container storage of flammable liquids and combustible liquids shall be in accordance with subsection 4.2.11;

• (i) storage tanks for flammable liquids and combustible liquids shall conform with section 4.3, with the exception of paragraph 4.3.13.1(1)(d), articles 4.3.13.5 and 4.3.15.2 and sentences 4.3.16.1(3) and (4);

• (j) piping and transfer systems for flammable liquids and combustible liquids shall conform with section 4.4, with the exception of articles 4.4.6.2, 4.4.11.1 and 4.4.11.2; and

• (k) flammable liquid and combustible liquid installations on piers and wharves shall conform with section 4.7, with the exception of article 4.7.10.2.

PART XIConfined Spaces

Interpretation

11.1 In this Part,

class of confined spaces

class of confined spaces means a group of at least two confined spaces that are likely, by reason of their similarity, to present the same hazards to persons entering, exiting or occupying them; (catégorie d’espaces clos)

confined space

confined space means an enclosed or partially enclosed space that

• (a) is not designed or intended for human occupancy except for the purpose of performing work,

• (b) has restricted means of access and egress, and

• (c) may become hazardous to any person entering it owing to

  • (i) its design, construction, location or atmosphere,

  • (ii) the materials or substances in it, or

  • (iii) any other conditions relating to it; (espace clos)

hot work

hot work means any work where flame is used or a source of ignition may be produced. (travail à chaud)

Hazard Assessment

• 11.2 (1) Where it is likely that a person will, in order to perform work for an employer, enter a confined space and an assessment pursuant to this subsection has not been carried out in respect of the confined space, or in respect of the class of confined spaces to which it belongs, the employer shall appoint a qualified person

  • (a) to carry out an assessment of the physical and chemical hazards to which the person is likely to be exposed in the confined space or the class of confined spaces; and

  • (b) to specify the tests that are necessary to determine whether the person would be likely to be exposed to any of the hazards identified pursuant to paragraph (a).

• (2) The qualified person referred to in subsection (1) shall, in a signed and dated report to the employer, record the findings of the assessment carried out pursuant to paragraph (1)(a).

• (3) The employer shall make a copy of any report made pursuant to subsection (2) available to the work place committee or the health and safety representative.

• (4) Subject to subsection (5), the report made pursuant to subsection (2) shall be reviewed by a qualified person at least once every three years to ensure that its assessment of the hazards with which it is concerned is still accurate.

• (5) If a confined space has not been entered in the three years preceding the time when the report referred to in subsection (4) should have been reviewed and no entry is scheduled, the report need not be reviewed until it becomes likely that a person will, in order to perform work for an employer, enter the confined space.

Entry Procedures

11.3 Every employer shall, after considering the report made pursuant to subsection 11.2(2),

• (a) in consultation with the work place committee or the health and safety representative, establish procedures, with the date on which they are established specified therein, that are to be followed by a person entering, exiting or occupying a confined space assessed pursuant to subsection 11.2(1), or a confined space that belongs to a class of confined spaces assessed pursuant to that subsection, and establish, where reasonably practicable, an entry permit system that provides for

  • (i) specifying, in each case, the length of time for which an entry permit is valid, and

  • (ii) recording

    • (A) the name of the person entering the confined space, and

    • (B) the date and time of entry and the anticipated time of exit;

• (b) specify the protection equipment referred to in Part XII that is to be used by every person who is granted access to the confined space by the employer;

• (c) specify any insulated protection equipment and tools referred to in Part VIII that a person may need in the confined space; and

• (d) specify the protection equipment and emergency equipment to be used by a person who takes part in the rescue of a person from the confined space or in responding to other emergency situations in the confined space.

Confined Space Entry

• 11.4 (1) The employer shall, where a person is about to enter a confined space, appoint a qualified person

  • (a) to verify, by means of tests, that compliance with the following specifications can be achieved during the period of time that the person will be in the confined space, namely,

    • (i) the concentration of any chemical agent or combination of chemical agents in the confined space to which the person is likely to be exposed will not result in the exposure of the person

      • (A) to a concentration of that chemical agent or combination of chemical agents in excess of the value referred to in paragraph 10.19(1)(a), or

      • (B) to a concentration of that chemical agent or combination of chemical agents in excess of the percentage set out in subsection 10.20(1), or in subsection 10.20(2) under the circumstances described in that subsection,

    • (ii) the concentration of airborne hazardous substances, other than chemical agents, in the confined space is not hazardous to the health or safety of the person, and

    • (iii) the percentage of oxygen in the air in the confined space is not less than 18 per cent by volume and not more than 23 per cent by volume, at normal atmospheric pressure;

  • (b) to verify that

    • (i) any liquid in which the person could drown has been removed from the confined space,

    • (ii) any free-flowing solid in which the person may become entrapped has been removed from the confined space,

    • (iii) the entry of any liquid, free-flowing solid or hazardous substance into the confined space has been prevented by a secure means of disconnection or by the fitting of blank flanges,

    • (iv) all electrical and mechanical equipment that may present a hazard to the person has been disconnected from its power source, real or residual, and has been locked out, and

    • (v) the opening for entry into and exit from the confined space is sufficient to allow the safe passage of a person using protection equipment; and

  • (c) subject to subsection 11.5(1), to verify that the specifications set out in paragraph (a) are complied with during all times that a person is in the confined space.

• (2) The qualified person referred to in subsection (1) shall, in a signed and dated report to the employer, set out the results of the verification carried out in accordance with that subsection, including the test methods, the test results and a list of the test equipment used.

• (3) The employer shall

  • (a) where the report made pursuant to subsection (2) indicates that a person who has entered the confined space has been in danger, send the report to the work place committee or the health and safety representative; and

  • (b) in all other cases, make a written copy or a machine-readable version of the report available to the work place committee or the health and safety representative.

Emergency Procedures and Equipment

• 11.5 (1) Where conditions in a confined space or the nature of the work to be performed in a confined space is such that the specifications set out in paragraph 11.4(1)(a) cannot be complied with during all times that a person is in the confined space, the employer shall

  • (a) in consultation with the work place committee or the health and safety representative, establish emergency procedures to be followed in the event of an accident or other emergency in or near the confined space, which procedures shall specify the date on which they are established and provide for the immediate evacuation of the confined space when

    • (i) an alarm is activated, or

    • (ii) there is any significant change in a concentration or percentage referred to in paragraph 11.4(1)(a) that would adversely affect the health or safety of a person in the confined space;

  • (b) provide the protection equipment referred to in paragraphs 11.3(b), (c) and (d) for each person who is about to enter the confined space;

  • (c) ensure that a qualified person trained in the entry and emergency procedures established pursuant to paragraph 11.3(a) and paragraph (a) is

    • (i) in attendance outside the confined space, and

    • (ii) in communication with the person inside the confined space;

  • (d) provide the qualified person referred to in paragraph (c) with a suitable alarm device for summoning assistance; and

  • (e) ensure that two or more persons are in the immediate vicinity of the confined space to assist in the event of an accident or other emergency.

• (2) One of the persons referred to in paragraph (1)(e) shall

  • (a) be trained in the emergency procedures established pursuant to paragraph (1)(a);

  • (b) be the holder of a basic first aid certificate; and

  • (c) be provided with the protection equipment and emergency equipment referred to in paragraph 11.3(d).

• (3) The employer shall ensure that every person entering, exiting or occupying a confined space referred to in subsection (1) wears an appropriate safety harness that is securely attached to a lifeline that

  • (a) is attached to a secure anchor outside the confined space;

  • (b) is controlled by the qualified person referred to in paragraph (1)(c);

  • (c) protects the person from the hazard for which it is provided and does not in itself create a hazard; and

  • (d) is, where reasonably practicable, equipped with a mechanical lifting device.

Record of Emergency Procedures and Equipment

• 11.6 (1) When a person is about to enter a confined space under circumstances such that the specifications set out in paragraph 11.4(1)(a) cannot be complied with, the qualified person referred to in paragraph 11.5(1)(c) shall, in a signed and dated report to the employer,

  • (a) specify those procedures established pursuant to paragraph 11.5(1)(a) that are to be followed and the protection equipment, insulated protection equipment and tools and the emergency equipment that are to be used; and

  • (b) specify any additional procedures and any other equipment that may be needed to ensure the health and safety of the person.

• (2) The report made pursuant to subsection (1) and any procedures specified therein shall be explained by the qualified person to every employee who is about to enter a confined space, and a copy of the report shall be signed and dated by any employee to whom the report and the procedures have been so explained, acknowledging by signature the reading of the report and the explanation thereof.

Provision and Use of Equipment

• 11.7 (1) The employer shall provide

  • (a) each person who is granted access to a confined space with the protection equipment specified pursuant to paragraph 11.3(b); and

  • (b) each person who is to undertake rescue operations with the protection equipment and emergency equipment specified pursuant to paragraph 11.3(d).

• (2) The employer shall ensure that every person who enters, exits or occupies a confined space follows the procedures established pursuant to paragraph 11.3(a) and uses the protection equipment specified pursuant to paragraphs 11.3(b) and (c).

Precaution

11.8 No person shall close off a confined space until a qualified person has verified that no person is inside it.

Hot Work

• 11.9 (1) Unless a qualified person has determined that the work can be performed safely, hot work shall not be performed in a confined space that contains

  • (a) an explosive or flammable hazardous substance in a concentration in excess of 10 per cent of its lower explosive limit; or

  • (b) oxygen in a concentration in excess of 23 per cent.

• (2) Where hot work is to be performed in a confined space that contains concentrations of flammable or explosive materials in excess of the concentration set out in paragraph (1)(a) or (b),

  • (a) a qualified person shall patrol the area surrounding the confined space and maintain a fire-protection watch in that area until all fire hazard has passed; and

  • (b) fire extinguishers specified as emergency equipment pursuant to paragraph 11.3(d) shall be provided in the area referred to in paragraph (a).

• (3) Where an airborne hazardous substance may be produced by hot work in a confined space, no person shall enter or occupy the confined space unless

  • (a) section 11.10 is complied with; or

  • (b) the person uses a respiratory protective device that meets the requirements of sections 12.2, 12.3 and 12.7.

Ventilation Equipment

• 11.10 (1) Where ventilation equipment is used to maintain the concentration of a chemical agent or combination of chemical agents in a confined space at or below the concentration referred to in subparagraph 11.4(1)(a)(i), or to maintain the percentage of oxygen in the air of a confined space within the limits referred to in subparagraph 11.4(1)(a)(iii), the employer shall not grant access to the confined space to any person unless

  • (a) the ventilation equipment is

    • (i) equipped with an alarm that will, if the equipment fails, be activated automatically and be audible or visible to every person in the confined space, or

    • (ii) monitored by an employee who is in constant attendance at the equipment and who is in communication with the person or persons in the confined space; and

  • (b) in the event of failure of the ventilation equipment, sufficient time will be available for the person to escape from the confined space before

    • (i) the concentration of the chemical agent or combination of chemical agents in the confined space exceeds the concentrations referred to in subparagraph 11.4(1)(a)(i), or

    • (ii) the percentage of oxygen in the air ceases to remain within the limits referred to in subparagraph 11.4(1)(a)(iii).

• (2) If the ventilation equipment fails to operate properly, the employee referred to in subparagraph (1)(a)(ii) shall immediately inform the person or persons in the confined space of the failure of the equipment.

Training

• 11.11 (1) The employer shall provide every employee who is likely to enter a confined space with instruction and training in

  • (a) the procedures established pursuant to paragraphs 11.3(a) and 11.5(1)(a); and

  • (b) the use of the protection equipment referred to in paragraphs 11.3(b), (c) and (d).

• (2) The employer shall ensure that no person enters a confined space unless the person is instructed in

  • (a) the procedures to be followed in accordance with paragraphs 11.3(a) and 11.5(1)(a); and

  • (b) the use of the protection equipment referred to in paragraphs 11.3(b), (c) and (d).

Record Keeping

11.12 The employer shall, at the employer’s place of business nearest to the work place in which the confined space is located, keep a written copy or a machine-readable version of

• (a) any report made pursuant to subsection 11.2(2) and the procedures established pursuant to paragraphs 11.3(a) and 11.5(1)(a) for a period of ten years after the date on which the qualified person signed the report or the procedures were established; and

• (b) any report made pursuant to subsection 11.4(2)

  • (i) for a period of ten years after the date on which the qualified person signed the report where the verification procedures undertaken pursuant to paragraphs 11.4(1)(a) and (c) indicate that the specifications set out in subparagraphs 11.4(1)(a)(i) to (iii) were not complied with, and

  • (ii) in every other case, for a period of two years after the date on which the qualified person signed the report.

PART XIISafety Materials, Equipment, Devices and Clothing

General

12.1 Where

• (a) it is not reasonably practicable to eliminate or control a health or safety hazard in a work place within safe limits, and

• (b) the use of protection equipment may prevent or reduce injury from that hazard,

every person granted access to the work place who is exposed to that hazard shall use the protection equipment prescribed by this Part.

12.2 All protection equipment referred to in section 12.1

• (a) shall be designed to protect the person from the hazard for which it is provided; and

• (b) shall not in itself create a hazard.

12.3 All protection equipment provided by the employer shall

• (a) be maintained, inspected and tested by a qualified person; and

• (b) where necessary to prevent a health hazard, be maintained in a clean and sanitary condition by a qualified person.

Protective Headwear

12.4 Where there is a hazard of head injury in a work place, protective headwear that meets the standards set out in CSA Standard Z94.1-M1977, Industrial Protective Headwear, the English version of which is dated April, 1977, as amended to September, 1982 and the French version of which is dated April, 1980 as amended to September, 1982, shall be used.

Protective Footwear

• 12.5 (1) Where there is a hazard of a foot injury or electric shock through footwear in a work place, protective footwear that meets the standards set out in CSA Standard Z195-M1984, Protective Footwear, the English version of which is dated March, 1984 and the French version of which is dated December, 1984, shall be used.

• (2) Where there is a hazard of slipping in a work place, non-slip footwear shall be used.

Eye and Face Protection

12.6 Where there is a hazard of injury to the eyes, face, ears or front of the neck of an employee in a work place, the employer shall provide eye or face protectors that meet the standards set out in CSA Standard Z94.3-M1982, Industrial Eye and Face Protectors, the English version of which is dated May, 1982 and the French version of which is dated February, 1983.

Respiratory Protection

• 12.7 (1) Where there is a hazard of an airborne hazardous substance or an oxygen deficient atmosphere in a work place, the employer shall provide a respiratory protective device that is listed in the NIOSH Certified Equipment List published on February 13, 1998 by the National Institute for Occupational Safety and Health, as amended from time to time, and that protects against the hazardous substance or oxygen deficiency, as the case may be.

• (2) A respiratory protective device referred to in subsection (1) shall be selected, fitted, cared for, used and maintained in accordance with the standards set out in CSA Standard Z94.4-M1982, Selection, Care and Use of Respirators, the English version of which is dated May, 1982, as amended to September, 1984 and the French version of which is dated March, 1983, as amended to September, 1984, excluding clauses 6.1.5, 10.3.3.1.2 and 10.3.3.4.2(c).

• (3) Where air is provided for the purpose of a respiratory protective device referred to in subsection (1),

  • (a) the air shall meet the standards set out in clauses 5.5.2 to 5.5.11 of CSA Standard CAN3-Z180.1-M85, Compressed Breathing Air and Systems, the English version of which is dated December 1985 and the French version of which is dated November 1987; and

  • (b) the system that supplies air shall be constructed, tested, operated and maintained in accordance with the CSA Standard referred to in paragraph (a).

12.8 Where a steel or aluminum self-contained breathing apparatus cylinder has a dent deeper than 1.5 mm and less than 50 mm in major diameter or shows evidence of deep isolated pitting, cracks or splits, the cylinder shall be removed from service until it has been shown to be safe for use by means of a hydrostatic test at a pressure equal to one and one-half times the maximum allowable working pressure.

Skin Protection

12.9 Where there is a hazard of injury or disease to or through the skin in a work place, the employer shall provide to every person granted access to the work place

• (a) a shield or screen;

• (b) a cream to protect the skin; or

• (c) an appropriate body covering.

Fall-Protection Systems

• 12.10 (1) Subject to subsection (1.1), every employer shall provide a fall-protection system to any person, other than an employee who is installing or removing a fall-protection system in accordance with the instructions referred to in subsection (5), who works

  • (a) from an unguarded structure or on a vehicle, at a height of more than 2.4 m above the nearest permanent safe level or above any moving parts of machinery or any other surface or thing that could cause injury to a person on contact;

  • (b) from a temporary structure at a height of more than 6 m above a permanent safe level; or

  • (c) from a ladder at a height of more than 2.4 m above the nearest permanent safe level where, because of the nature of the work, that person is unable to use at least one hand to hold onto the ladder.

• (1.1) Where an employee is required to work on a vehicle on which it is not reasonably practicable to provide a fall-protection system, the employer shall

  • (a) in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative,

  • (i) perform a job safety analysis to eliminate or minimize the need for the employee to climb onto the vehicle or its load, and

  • (ii) provide every employee who is likely to climb onto the vehicle or its load with training and instruction on the safe method of climbing onto and working on the vehicle or its load;

  • (b) make a report in writing to the regional health and safety officer setting out the reasons why it is not reasonably practicable to provide a fall-protection system and include the job safety analysis and a description of the training and instruction referred to in paragraph (a); and

  • (c) provide a copy of the report referred to in paragraph (b) to the policy committee or, if there is no policy committee, the work place committee or the health and safety representative.

• (1.2) The job safety analysis, training and instruction referred to in paragraph (1.1)(a) shall be reviewed every two years in consultation with the policy committee or, if there is no policy committee, the work place committee or the health and safety representative.

• (2) The components of a fall-protection system shall meet the following standards:

  • (a) CSA Standard Z259.1-1976, Fall-Arresting Safety Belts and Lanyards for the Construction and Mining Industries, the English version of which is dated November, 1976, as amended to May, 1979 and the French version of which is dated April, 1980;

  • (b) CSA Standard Z259.2-M1979, Fall-Arresting Devices, Personnel Lowering Devices and Life Lines, the English version of which is dated November, 1979 and the French version of which is dated October, 1983; and

  • (c) CSA Standard Z259.3-M1978, Lineman’s Body Belt and Lineman’s Safety Strap, the English version of which is dated September, 1978, as amended to April, 1981 and the French version of which is dated April, 1980, as amended to April, 1981.

• (3) The anchor of a fall-protection system shall be capable of withstanding a force of 17.8 kN.

• (4) A fall-protection system that is used to arrest the fall of a person shall prevent that person

  • (a) from being subjected to a peak fall arrest force greater than 8 kN; and

  • (b) from falling freely for more than 1.2 m.

• (5) Where an employee is about to install or remove a fall-protection system, the employer shall

  • (a) prepare written instructions for the safe installation or removal of the fall-protection system; and

  • (b) keep a copy of the instructions readily available for the information of the employee.

Protection Against Drowning

• 12.11 (1) Where, in a work place, there is a hazard of drowning, the employer shall provide every person granted access to the work place with

  • (a) a life jacket or buoyancy device that meets the standards set out in the Canadian General Standards Board Standard

    • (i) CAN2-65.7-M80, Life Jackets, Inherently Buoyant Type, dated April, 1980, or

    • (ii) 65-GP-11, Standard for: Personal Flotation Devices, dated October, 1972; or

  • (b) a safety net or a fall-protection system.

• (2) Where, in a work place, there is a hazard of drowning,

  • (a) emergency equipment shall be provided and held in readiness;

  • (b) a person who is qualified to operate all the emergency equipment provided shall be available;

  • (c) if appropriate, a powered boat shall be provided and held in readiness; and

  • (d) written emergency procedures shall be prepared by the employer containing

    • (i) a full description of the procedures to be followed and the responsibilities of all persons granted access to the work place, and

    • (ii) the location of any emergency equipment.

• (3) Where a work place is a wharf, dock, pier, quay or other similar structure, a ladder that extends at least two rungs below water level shall be affixed to the face of the structure every 60 m along its length.

Loose Clothing

12.12 Loose clothing, long hair, dangling accessories, jewellery or other similar items that are likely to be hazardous to the health or safety of an employee in a work place shall not be worn unless they are so tied, covered or otherwise secured as to prevent the hazard.

Protection Against Moving Vehicles

12.13 Where an employee is regularly exposed to contact with moving vehicles during his work, he shall

• (a) wear a high-visibility vest or other similar clothing, or

• (b) be protected by a barricade

that is readily visible under all conditions of use.

Records

• 12.14 (1) A record of all protection equipment provided by the employer shall be kept by him in the work place in which the equipment is located for a period of two years after it ceases to be used.

• (2) The record referred to in subsection (1) shall contain

  • (a) a description of the equipment and the date of its acquisition by the employer;

  • (b) the date and result of each inspection and test of the equipment;

  • (c) the date and nature of any maintenance work performed on the equipment since its acquisition by the employer; and

  • (d) the name of the person who performed the inspection, test or maintenance of the equipment.

Instructions and Training

• 12.15 (1) Every person granted access to the work place who uses protection equipment shall be instructed by the employer in the use of the equipment.

• (2) Every employee who uses protection equipment shall be instructed and trained in the use, operation and maintenance of the equipment.

• (3) Every person granted access to a work place shall be instructed in respect of the written emergency procedures referred to in paragraph 12.11(2)(d).

• (4) The instructions referred to in subsections (2) and (3) shall be

  • (a) set out in writing; and

  • (b) kept by the employer readily available for examination by every person granted access to the work place.

Defective Protection Equipment

12.16 Where an employee finds any defect in protection equipment that may render it unsafe for use, he shall report the defect to his employer as soon as possible.

12.17 An employer shall mark or tag as unsafe and remove from service any protection equipment used by his employees that has a defect that may render it unsafe for use.

PART XIIITools and Machinery

Interpretation

13.1 In this Part, explosive actuated fastening tool means a tool that, by means of an explosive force, propels or discharges a fastener for the purpose of impinging it on, affixing it to or causing it to penetrate another object or material. (pistolet de scellement à cartouches explosives)

Design, Construction, Operation and Use of Tools

13.2 The exterior surface of any tool used by an employee in a fire hazard area shall be made of non-sparking material.

13.3 All portable electric tools used by employees shall meet the standards set out in CSA Standard CAN C22.2 No. 71.1-M89, Portable Electric Tools, the English version of which is dated September 1989 and the French version of which is dated February 1991.

• 13.4 (1) Subject to subsection (2), all portable electric tools used by employees shall be grounded.

• (2) Subsection (1) does not apply to tools that

  • (a) are powered by a self-contained battery;

  • (b) have a protective system of double insulation; or

  • (c) are used in a location where reliable grounding cannot be obtained if the tools are supplied from a double insulated portable ground fault circuit interrupter of the class A type that meets the standards set out in CSA Standard C22.2 No. 144-1977, Ground Fault Circuit Interrupters, dated March, 1977.

13.5 All portable electric tools used by employees in a fire hazard area shall be marked as appropriate for use or designed for use in the area of that hazard.

13.6 Where an air hose is connected to a portable air-powered tool used by an employee, a restraining device shall be attached

• (a) where an employee may be injured by the tool falling, to the tool; and

• (b) to all hose connections, in order to prevent injury to an employee in the event of an accidental disconnection of a hose.

• 13.7 (1) All explosive actuated fastening tools used by employees shall meet the standards set out in CSA Standard Z166-1975, Explosive Actuated Fastening Tools, dated June, 1975.

• (2) No employee shall operate an explosive actuated fastening tool unless authorized to do so by his employer.

• (3) Every employee who operates an explosive actuated fastening tool shall operate it in accordance with the CSA Standard referred to in subsection (1).

13.8 All chain saws used by employees shall meet the standards set out in CSA Standard CAN3-Z62.1-M85, Chain Saws, dated February, 1985.

Defective Tools and Machines

13.9 Where an employee finds any defect in a tool or machine that may render it unsafe for use, he shall report the defect to his employer as soon as possible.

13.10 An employer shall mark or tag as unsafe and remove from service any tool or machine used by his employees that has a defect that may render it unsafe for use.

Instructions and Training

13.11 Every employee shall be instructed and trained by a qualified person appointed by his employer in the safe and proper inspection, maintenance and use of all tools and machinery that he is required to use.

• 13.12 (1) Every employer shall maintain a manual of operating instructions for each type of portable electric tool, portable air-powered tool, explosive actuated fastening tool and machine used by his employees.

• (2) A manual referred to in subsection (1) shall be kept by the employer readily available for examination by an employee who is required to use the tool or machine to which the manual applies.

General Requirements for Machine Guards

• 13.13 (1) Every machine that has exposed moving, rotating, electrically charged or hot parts or that processes, transports or handles material that constitutes a hazard to an employee shall be equipped with a machine guard that

  • (a) prevents the employee or any part of his body from coming into contact with the parts or material;

  • (b) prevents access by the employee to the area of exposure to the hazard during the operation of the machine; or

  • (c) makes the machine inoperative if the employee or any part of his clothing is in or near a part of the machine that is likely to cause injury.

• (2) To the extent that is reasonably practicable, a machine guard referred to in subsection (1) shall not be removable.

• (3) A machine guard shall be so constructed, installed and maintained that it meets the requirements of subsection (1).

Use, Operation, Repair and Maintenance of Machine Guards

13.14 Machine guards shall be operated, maintained and repaired by a qualified person.

13.15 Subject to section 13.16, where a machine guard is installed on a machine, no person shall use or operate the machine unless the machine guard is in its proper position.

• 13.16 (1) Subject to subsection (2), where it is necessary to remove a machine guard from a machine in order to perform repair or maintenance work on the machine, no person shall perform the repair or maintenance work unless the machine has been locked out in accordance with a written lock out procedure provided by the employer.

• (2) Where it is not reasonably practicable to lock out a machine referred to in subsection (1) in order to perform repair or maintenance work on the machine, the work may be performed if

  • (a) the person performing the work follows written instructions provided by the employer that will ensure that any hazard to that person is not significantly greater than it would be if the machine had been locked out; and

  • (b) the person performing the work

    • (i) obtains a written authorization from the employer each time the work is performed, and

    • (ii) performs the work under the direct supervision of a qualified person.

13.17 A copy of the instructions referred to in section 13.16 shall be kept readily available by the employer for the information of persons who perform repair and maintenance work on his machines.

Abrasive Wheels

13.18 Abrasive wheels shall be

• (a) used only on machines equipped with machine guards,

• (b) mounted between flanges, and

• (c) operated

in accordance with sections 4 to 6 of CSA Standard B173.5-1979, Safety Requirements for the Use, Care and Protection of Abrasive Wheels, dated February, 1979.

13.19 A bench grinder shall be equipped with a work rest or other device that

• (a) prevents the work piece from jamming between the abrasive wheel and the wheel guard; and

• (b) does not make contact with the abrasive wheel at any time.

Mechanical Power Transmission Apparatus

13.20 Equipment used in the mechanical transmission of power shall be guarded in accordance with sections 7 to 10 of ANSI Standard ANSI B15.1-1972, Safety Standard for Mechanical Power Transmission Apparatus, dated July, 1972.

Woodworking Machinery

13.21 Woodworking machinery shall be guarded in accordance with clause 3.3 of CSA Standard Z114-M1977, Safety Code for the Woodworking Industry, dated March, 1977.

Punch Presses

13.22 Punch presses shall meet the standards set out in CSA Standard Z142-1976, Code for the Guarding of Punch Presses at Point of Operation, dated February, 1976.

PART XIVMaterials Handling

Interpretation

14.1 In this Part,

materials handling equipment

materials handling equipment means equipment, including its supporting structures, auxiliary equipment and rigging devices, used to transport, lift, move or position persons, materials, goods or things and includes mobile equipment used to lift, hoist or position persons, but does not include an elevating device that is permanently installed in a building; (appareil de manutention)

motorized hand-rider truck

motorized hand-rider truck means motorized materials handling equipment that is designed to be controlled by a walking or onboard operator; (chariot à conducteur porté ou accompagnant)

operator

operator means a person who controls the operation of motorized or manual materials handling equipment and who has received or is receiving instruction and training in respect of the procedures referred to in subsection 14.23(1) or (3), as the case may be; (opérateur)

safe working load

safe working load means the maximum load that the motorized or manual materials handling equipment is designed and constructed to handle or support safely under particular operating conditions; (charge de travail admissible)

signaller

signaller means a person instructed by an employer to direct, by means of visual or auditory signals, the safe movement and operation of motorized materials handling equipment. (signaleur)

Application

14.2 This Part does not apply in respect of

• (a) subject to subsection 14.4(4), the use and operation of motor vehicles on public roads;

• (b) the use and operation of tackle regulated pursuant to the Canada Shipping Act in the loading or unloading of ships; or

• (c) the underground workings of mines.

DIVISION IDESIGN AND CONSTRUCTION

General

• 14.3 (1) Motorized and manual materials handling equipment shall, to the extent that is reasonably practicable, be so designed and constructed that if there is a failure of any part of the materials handling equipment, that failure will not result in loss of control of the materials handling equipment or create a hazardous condition.

• (2) All glass and other transparent materials used in doors, windows and other parts of motorized materials handling equipment shall be of a type that does not shatter into sharp or dangerous pieces on impact.

• (3) Subject to subsection 14.51(1), an employer shall ensure that the onboard operator’s compartment in, or position on, motorized materials handling equipment provides adequate adjustability of range to accommodate properly the operator for the work that is required to be done.

Protection from Falling Objects

• 14.4 (1) Where motorized materials handling equipment is used under such circumstances that the onboard operator of the equipment may be struck by a falling object or shifting load, the employer shall equip the motorized materials handling equipment with a protective structure of such a design, construction and strength that it will, under all foreseeable conditions, prevent the penetration of the object or load into the compartment or position occupied by the operator.

• (2) Subsection (1) does not apply to a motorized hand-rider truck unless there is a likelihood of its operator being struck by a falling object or a shifting load.

• (3) A protective structure referred to in subsection (1) shall be

  • (a) constructed of non-combustible or fire-resistant material; and

  • (b) designed to permit quick exit from the motorized materials handling equipment in an emergency.

• (4) Where there is a likelihood that materials, goods or things will shift and endanger employees in a motor vehicle acquired after July 1, 1995 and having a gross vehicle weight of less than 4,500 kg, the employer shall install a bulkhead or other means to protect the employees.

14.5 Where during the loading or unloading of motorized materials handling equipment the load will pass over the operator’s compartment or position, the operator shall not occupy that compartment in, or position on, the equipment unless it is equipped with a protective structure required under section 14.4.

Protection from Overturning

• 14.6 (1) Subject to subsection 14.51(2), where motorized materials handling equipment is used in circumstances where it may turn over, it shall be fitted with a rollover protection device that meets the standards set out in CSA Standard B352-M1980, Rollover Protective Structures (ROPS) for Agricultural, Construction, Earthmoving, Forestry, Industrial, and Mining Machines, the English version of which is dated September 1980 and the French version of which is dated April 1991, as amended from time to time, and that will prevent the operator of the motorized materials handling equipment from being trapped or crushed under the equipment if it does turn over.

• (2) Subject to subsection 14.51(1), all motorized materials handling equipment used in circumstances described in subsection (1) shall be fitted with

  • (a) seat-belts; and

  • (b) restraining devices preventing the displacement of the battery if the equipment turns over.