Special Economic Measures (Iran) Regulations (SOR/2010-165)

Regulations are current to 2017-10-13 and last amended on 2016-02-05. Previous Versions

SCHEDULE 2(Section 4)

Goods

ItemColumn 1Column 2
GoodsDescription
1Aerodynamic particle size measuring equipmentAny equipment designed to measure in real time the aerodynamic particle size of aerosols in the range of 0.1 to 50 micrometers.
2Aerosol generatorsAny equipment capable of producing aerosols of radioactive, chemical or biological materials with aerodynamic particle sizes in the range of 0.1 to 50 micrometres.
3Aluminum and aluminum alloy productsPiping, tubing, fittings, flanges, forging, castings, valves, any unfinished products in any form and any waste or scrap that are made of aluminum and its alloys that are not specified in the Export Control List.
4Argon ion lasersArgon ion lasers that are not specified in the Export Control List and have an average output power equal to or greater than 5 W.
5Autoclaves (double-ended)Double-ended or pass-through autoclaves with internal volume greater than 1 m3, bioseal, interlocking doors, warning lights or audible alarms.
6Automated take-off or landing systemsSystems that are usable in the systems specified in entry 6-1.A.2 of the Guide and are capable of operating vehicles with a stall speed in excess of 30 knots.
7Batch centrifugesBatch centrifuges with a rotor capacity of 25 L or greater, usable with biological material.
8Bellows-sealed scroll compressors and vacuum pumps
  • (1) The following vacuum pumps:

    • (a) turbomolecular pumps having a flow-rate equal to or greater than 400 l/s;

    • (b) Roots-type roughing pumps having a volumetric aspiration flow-rate greater than 200 m³/hr;

    • (c) bellows-sealed, scroll, dry pumps; and

    • (d) bellows-sealed, scroll, dry compressor pumps.

  • (2) Vacuum pumps that are not specified in the Export Control List and that

    • (a) are suitable for corrosive fluids;

    • (b) have a maximum flow-rate greater than 5 m³/hr, measured under standard temperature and pressure conditions of 273 K (0°C) and 101.3 kPa, respectively; and

    • (c) are pumps in which all surfaces that may come into direct contact with fluids consist of stainless steel, aluminium alloy or a combination of the two.

9Decanning and decladding equipmentMechanical equipment designed or usable for decanning or decladding spent nuclear reactor fuel as part of a fuel processing process.
10Drum drying equipmentAny drum drying equipment capable of producing dry particles of radioactive, chemical or biological materials with aerodynamic particle sizes in the range of 0.1 to 50 micrometres.
11Electrical power supply units and transformers

High voltage direct current power supply units that are not specified in the Export Control List and

  • (a) are capable of continuously producing 10 kV or more over a period of 8 hours, with output power of 5 kW or more with or without sweeping; and

  • (b) have current or voltage stability better than 0.1% over a period of 4 hours.

12Electrolytic cells for fluorine products

Electrolytic cells that are not specified in the Export Control List that

  • (a) are used for fluorine production; and

  • (b) have an output capacity greater than 100 g of fluorine per hour.

13Fibrous or filamentary materials

The following fibrous or filamentary materials or prepregs that are not specified in the Export Control List:

  • (a) carbon or aramid fibrous or filamentary materials having either

    • (i) a specific modulus exceeding 10 x 10^6 m, or

    • (ii) a specific tensile strength exceeding 17 x 10^4 m;

  • (b) glass fibrous or filamentary materials having either

    • (i) a specific modulus exceeding 3.18 x 10^6 m, or

    • (ii) a specific tensile strength exceeding 76.2 x 10^3 m; and

  • (c) thermoset resin-impregnated continuous yarns, rovings, tows and tapes with a width of 15 mm or less (prepregs), made for carbon or glass fibrous or filamentary materials.

14Flow-forming machines

Flow-forming machines and spin-forming machines capable of flow-forming functions and mandrels, as follows:

  • (a) machines that have three or more rollers and that can be equipped with numerical control units or a computer control; and

  • (b) rotor-forming mandrels designed to form cylindrical rotors with an inside diameter between 75 and 400 mm.

15Frequency changers (inverters) and specially designed software for them
  • (1) Frequency changers that

    • (a) have multiphase frequency output;

    • (b) are capable of providing power of 40 W or greater;

    • (c) are capable of operating anywhere between 600 and 2000 Hz; and

    • (d) have frequency control less than 0.2%.

  • (2) Specially designed software for these frequency changers.

16Glove boxesAny glove boxes or similar devices with remote manipulators that can provide the operator with protection from radiation or radioactive materials.
17Heat treatment and sintering furnacesControlled-atmosphere heat treatment furnaces capable of operation at temperatures above 400°C.
18HEPA filtersHEPA filters of a frame area of 0.0625 m2 or larger with a DOP rating of 99.997% (at 0.3 micron) or higher.
19High speed camerasElectronic framing cameras having a speed exceeding 1000 frames per second.
20Lead in sheets or blocks/bricksMust be suitable for use in shielding.
21Magnetic alloys in thin strip formMagnetic alloy materials in sheet or thin strip form with a thickness of 0.1 mm or less, made of iron-chromium-cobalt, iron-cobalt-vanadium, iron-chromium-cobalt-vanadium or iron-chromium.
22Mass spectrometers

The following mass spectrometers that are not specified in the Export Control List that are capable of measuring ions of 200 atomic mass units or more and have a resolution of better than 2 parts in 200:

  • (a) inductively coupled plasma mass spectrometers (ICP/MS);

  • (b) glow discharge mass spectrometers (GDMS);

  • (c) thermal ionization mass spectrometers (TIMS);

  • (d) electron bombardment mass spectrometers with a source chamber constructed from, lined with or plated with, materials resistant to corrosion by UF6;

  • (e) molecular beam mass spectrometers with either

    • (i) a source chamber constructed from, lined with or plated with, stainless steel or molybdenum and equipped with a cold trap capable of cooling to 193 K (-80°C) or less, or

    • (ii) a source chamber constructed from, lined with or plated with, materials resistant to corrosion by UF6; and

  • (f) mass spectrometers equipped with a microfluorination ion source usable with actinides or actinide fluorides.

23Nucleic acid synthesisersAny device designed to produce oligonucleotides from nucleic acids or derivatives.
24Oxidation furnacesFurnaces capable of operation at temperatures over 400°C.
25Riot gearRiot helmets and associated equipment, balaclavas, flashbangs, sting-ball grenades, impact munitions, chemical munitions, clothing specifically used for physical protection in riot control situations, batons and paintball guns.
26Sintered metal filters employing monel or other high nickel content alloys

Sintered metal filters made of

  • (a) nickel; or

  • (b) nickel alloy with a nickel content of 40% or more by weight.

27Sintering pressesSintering systems, including parts, software and technology for them, capable of generating a temperature in excess of 999°C or atmospheric pressure of less than 2 atmospheres.
28Tributyl phosphate (TBP)Chemical Abstract Service registry number 126-73-8.
29Absolute pressure transducersAbsolute pressure transducers capable of measuring absolute pressures below 100 kPa, and specially designed parts and software for them.
30Gamma-ray spectrometersGamma-ray spectrometers of all types and specifications, and specially designed parts and software for them.
31Numerically controlled machine toolsNumerically controlled machine tools of all types, and specially designed parts and software for them.
32Electroslag remeltersElectroslag remelters of all types and specifications, and specially designed parts for them.
33Gold, silver, platinum, palladium, ruthenium, rhodium, osmium and iridiumIn addition to specific items made of those metals referred to in these Regulations, all raw, semi-finished or finished forms of those metals or their alloys.
34Helium or hydrogen leak detectorsHelium or hydrogen leak detectors capable of detecting leak rates of less than 1 x 10-5 standard cubic centimetres of air per second (atm cc/s for air).
35Smelting machinery and productsAny smelting machines and specially designed parts for them, as well as any reducing agents or fluxes used in the smelting process.
36Stainless steel valves, piping, tubing and fittingsAny valves, piping, tubing and fittings that are made of stainless steel type 304, 316 or 317 and that are not specified in the Export Control List.
37Maraging steelsMaraging steels in the Export Control List 6-6.C.8 having an ultimate tensile strength equal to or greater than 2.05 GPa, measured at 20°C, in the form of sheet, plate or tubing with a wall or plate thickness equal to or less than 5.0 mm and usable in systems specified in 6-1.A or 6-19.A.1 of the Guide.
38Explosive release devicesExplosive bolts
39Isocyanates

Propellants and constituent chemicals for propellants, either as a pure substance or as a mixture containing at least 50% of one of the following chemicals:

  • (a) toluene diisocyanate (TDI);

  • (b) methyl diphenyl diisocyanate (MDI);

  • (c) isophorone diisocyanate (IPDI);

  • (d) sodium perchlorate;

  • (e) xylidine;

  • (f) hydroxy terminated polyether (HTPE); or

  • (g) hydroxy terminated caprolactone ether (HTCE).

40Production equipmentComputer controlled or numerically controlled laser welding and laser cutting machines, and their specially designed components.
41Production equipmentComputer controlled or numerically controlled electron beam welding machines, and their specially designed components.
  • SOR/2011-268, ss. 12, 13;
  • SOR/2012-283, s. 10;
  • SOR/2016-15, s. 12.
 
Date modified: