Marine Machinery Regulations
Version of the schedule from 2015-06-17 to 2021-06-22:
SCHEDULE VTurbine Engines
SCHEDULE VTurbine Engines
PART I(Section 4)Design Specifications
DIVISION ISteam Turbine Engines
| Item | Requirements |
|---|---|
| 1 | None. |
DIVISION IIGas Turbine Engines
| Item | Requirements |
|---|---|
| 1 | None. |
PART II(Section 6)Plans
DIVISION ISteam Turbine Engines
| Item | Required Information |
|---|---|
| 1 | General arrangement of the installation of the engine in the ship, showing all connected systems. |
| 2 | General arrangement and sectional elevation of the engine and means of support. |
| 3 | Specifications for ahead and astern turbines indicating maximum continuous brake power and corresponding revolutions per minute, steam pressures and temperatures at turbine inlet and exhaust, full details of cylinders, rotors, nozzles, blades, couplings and clutches, full details of physical properties of principal parts, details of forgings, castings and weldments, details of the heat treatment process and testing procedures. |
| 4 | Details of bearings and lubricating oil systems. |
| 5 | Details of controls including reversing arrangements. |
| 6 | Details of speed-regulating governors, lubricating oil failure-protection arrangements and other safety devices. |
| 7 | Details of engine turning gear. |
| 8 | Details of critical speeds of rotating assemblies including vibration analyses. |
DIVISION IIGas Turbine Engines
| Item | Required Information |
|---|---|
| 1 | General arrangement of the installation of the engine in the ship, showing all connected systems. |
| 2 | General arrangement and sectional elevation of the engine and means of support. |
| 3 | Specifications of the turbine and compressor indicating maximum continuous brake power and corresponding revolutions per minute, gas pressures and temperatures, full details of casings, combustion chambers, rotors, nozzles, blades, heat exchangers, couplings and clutches, full details of physical properties of principal parts, details of forgings, castings and weldments, details of the heat treatment process and testing procedures. |
| 4 | Details of fuel system including fuel oil viscosities required for starting and running. |
| 5 | Details of air inlet and exhaust arrangements. |
| 6 | Details of controls including means of starting and of fuel ignition. |
| 7 | Details of bearings and of lubricating oil systems. |
| 8 | Details of speed-regulating governors, lubricating oil failure protection arrangements and other safety devices. |
| 9 | Details of engine turning gear. |
| 10 | Details of critical speeds of rotating assemblies including vibration analyses. |
| 11 | Information set out in items 1 to 10 is not required to be submitted for
|
PART III(Subsection 12(2))Construction and Installation Inspections
DIVISION IConstruction Inspection
| Item | Requirements |
|---|---|
| 1 | Identification from material test certificates, before construction is commenced, of materials to be used, including welding metal, for the following parts:
|
| 2 | Verification that welding was carried out by welders certified by a Provincial Government of Canada, or another authority having similar standards where the welding was carried out outside Canada, for the class of work to be done. |
| 3 | Inspection of welds, including non-destructive test examination and verification of any required heat treatment process in accordance with rules or codes. |
| 4 | Verification of rotor balance and thermal stability testing in accordance with rules or codes. |
| 5 | Identification of components from component inspection certificates and inspection of components and their installation. |
| 6 | Witnessing of hydrostatic pressure tests of components in accordance with rules or codes. |
| 7 | Inspection of the constructed engine and witnessing of the engine operation under test. |
DIVISION IIInstallation Inspection
| Item | Requirements |
|---|---|
| 1 | Verification of correct alignment of securing arrangements. |
| 2 | Verification of correct adjustment and operational condition of the connection of the engine to associated systems. |
| 3 | Verification of correct adjustment and operational condition of safety, control and monitoring devices. |
| 4 | Verification of reliability and sufficiency under trials up to full power under normal working conditions for a suitable endurance period of not less than 2 hours, taking into consideration the size and the complexity of the gas turbine engine or steam turbine engine. |
PART IVPeriodic General and Special Inspections
DIVISION I(Section 19)Periodic General Inspection
| Item | Requirements |
|---|---|
| 1 | Operational condition of the engine. |
| 2 | Correct adjustment and operational condition of safety devices. |
| 3 | Locations where fluid leakage, metal wastage, overheating, heavy vibration or excessive bearing clearance may occur. |
| 4 | Correct adjustment of controls and monitoring systems. |
| 5 | Operational condition of alarm systems, particularly where the engine is designed for non-continuous local supervision. |
DIVISION IIPeriodic Special Inspection
SUBDIVISION I(Subsection 20(1))Parts to be Inspected
| Item | Requirements |
|---|---|
| 1 | Casings, glands, nozzles, blades, valves and valve mechanisms. |
| 2 | Rotors, blades, couplings, thrusts, bearings and bolts. |
| 3 | Speed-regulating governors and other safety devices. |
| 4 | Attached pumps. |
| 5 | Compressors, combustion chambers, heat exchangers, air inlet, fuel and exhaust, and starting system for a gas turbine engine. |
| 6 | Engine structure and fastenings without dismantling if a general examination shows that the condition of the components is adequate for further service. |
| 7 | No inspection is required for speed-regulating governors and other complex mechanisms where written information is provided to the inspector by firms specializing in the reconditioning of those mechanisms, indicating that the parts are in good order and adjustment. |
SUBDIVISION II(Subsection 20(2))Intervals
| Item | Requirements |
|---|---|
| 1 | For gas turbine engines and steam turbine engines, at intervals not exceeding 5 years. |
| 2 | Notwithstanding item 1, the first lifting of the casing and rotor of a steam turbine engine that has more than one propulsion ahead turbine with an emergency crossover arrangement is deferred until the engine is 10 years old if the inspector is satisfied that the turbine is in good operating condition based on the records of the vibration indicator, the rotor position indicator and the turbine operation. |
- SOR/2015-161, s. 7(F)
- Date modified: