Motor Vehicle Restraint Systems and Booster Seats Safety Regulations (SOR/2010-90)

Regulations are current to 2019-06-20 and last amended on 2015-05-15. Previous Versions

PART 6CMVSS 213.5 — Restraint Systems for Infants with Special Needs (continued)

Contactable Surfaces

Marginal note:Contactable surfaces

  •  (1) Every restraint system for infants with special needs, other than a car bed must provide

    • (a) for the support of the infant’s back, a continuous surface that is flat or concave and has an area of not less than 54 800 mm2; and

    • (b) for the support of the sides of the infant’s torso, continuous surfaces that are flat or concave and have an area of not less than 30 500 mm2 each.

  • Marginal note:Contactable surfaces — car bed

    (2) Every car bed must provide

    • (a) for the support of the infant’s back and legs, a continuous surface that is flat or concave and has an area of not less than 71 250 mm2; and

    • (b) for the support of the sides of the infant’s torso and legs, continuous surfaces that are flat or concave and have an area of not less than 39 650 mm2 each.

Marginal note:Rigid structural elements

 Any rigid structural element underlying a contactable surface of a restraint system for infants with special needs must not have

  • (a) a protrusion, with any padding or flexible overlay material removed, of more than 9.5 mm; or

  • (b) an exposed edge with a radius of less than 6.4 mm.

Marginal note:Surface contactable by head

 Every surface of a restraint system for infants with special needs that is contactable by the head of an anthropomorphic test device positioned in the restraint system in accordance with, in the case of a car bed, subsection 4.5.2 or 4.6.2 of Test Method 213.5 or, in the case of all other restraint systems for infants with special needs, subsection 4.5.3 or 4.6.3 of Test Method 213.5 must be covered with slow-recovery, energy-absorbing material that, when tested in accordance with section 6 of Test Method 213.5, has

  • (a) a resistance of not less than 4 kPa but not more than 70 kPa at 25% of compression-deflection resistance;

  • (b) a thickness of not less than 12 mm, if the material has a resistance of not less than 12 kPa but not more than 70 kPa at 25% of compression-deflection resistance; and

  • (c) a thickness of not less than 19 mm, if the material has a resistance of not less than 4 kPa but less than 12 kPa at 25% of compression-deflection resistance.

Testing

Marginal note:Dynamic testing

  •  (1) A restraint system for infants with special needs that is subjected to a dynamic test in accordance with section 4 of Test Method 213.5 must, if the adjustment position of each component of the restraint system is in accordance with the manufacturer’s instructions,

    • (a) exhibit no complete separation of any load-bearing structural element, and no partial separation exposing a surface with

      • (i) a protrusion of more than 9.5 mm, or

      • (ii) a radius of less than 6.4 mm;

    • (b) in the case of a restraint system other than a car bed, remain in the same adjustment position during the test as it was in immediately before the test began, except that, if the restraint system has a means of automatically repositioning the seating surface to allow the anthropomorphic test device to move from a reclined position to a more upright position and back to a reclined position during the test, the seating surface does not have to remain in the same adjustment position during the test as it was in immediately before the test began;

    • (c) in the case of a restraint system other than a car bed, retain the torso of the anthropomorphic test device within the restraint system, and not allow any portion of the target points on either side of the device’s head, located on the transverse axis passing through the centre of mass of the device’s head and perpendicular to the head’s midsagittal plane, to pass at any time, during or immediately after the test, through the transverse orthogonal planes formed by the extension of the seat back frontal surface plane of the restraint system and by the plane that passes through the uppermost point of the restraint system, as shown in Figure 7 of Schedule 7, or through the vertical transverse plane passing through point X on the standard seat assembly, as shown in Figure 8 of Schedule 7;

    • (d) in the case of a restraint system other than a car bed, not allow the angle between the vertical and the back and head support surface, measured 240 mm above the seating surface, to be more than 70° at any time during the test;

    • (e) in the case of a restraint system other than a car bed, limit the movement of the head of the anthropomorphic test device towards the rear of the restraint system by means of a continuous seat back that is an integral part of the restraint system;

    • (f) in the case of a restraint system other than a car bed, limit the rotation of the head of the anthropomorphic test device towards the rear of the restraint system, in its midsagittal plane, by means of a continuous seat back that is an integral part of the restraint system, so that the angle between the head and the torso is at no time during the test more than 45° as compared to the angle between the head and the torso prior to the test; and

    • (g) in the case of a car bed, retain the head, neck and torso of the anthropomorphic test device within the confines of the car bed.

  • Marginal note:Dynamic testing — levelling device

    (2) A restraint system for infants with special needs that is equipped with a levelling device and that is subjected to a dynamic test in accordance with section 4 of Test Method 213.5 must conform to the requirements of paragraphs (1)(a) and (b) if the adjustment position of each component of the restraint system, except the levelling device, is in accordance with the manufacturer’s instructions.

  • Marginal note:Continuous seat back

    (3) The continuous seat back referred to in paragraphs (1)(e) and (f) must

    • (a) have a height of at least 500 mm;

    • (b) have a width of at least 200 mm, measured in the horizontal plane at the height specified in paragraph (a); and

    • (c) not impose any loads on the top of the head of the anthropomorphic test device during the dynamic test referred to in subsection (1).

  • Marginal note:Measurement of height — paragraph 3(a)

    (4) The height referred to in paragraph (3)(a) must be measured in a plane parallel to the surface of the seat back of the restraint system for infants with special needs and orthogonal to the vertical longitudinal plane passing through the longitudinal centreline of the restraint system, from the lowest point of the restraint system’s seating surface that is contacted by the buttocks of the seated anthropomorphic test device.

  • Marginal note:Exception

    (5) Despite paragraph (3)(b), if the restraint system for infants with special needs provides surfaces for the support of the sides of the torso, and those surfaces extend at least 100 mm forward from the padded surface of the portion of the restraint system provided for the support of the head of the anthropomorphic test device, the restraint system may have a continuous seat back width of not less than 150 mm, measured in the horizontal plane at the height specified in paragraph (3)(a).

  • Marginal note:Restraint system with means of automatic repositioning

    (6) If a restraint system for infants with special needs that has a means of automatically repositioning the seating surface is subjected, in any adjustment position, to a dynamic test in accordance with section 4 of Test Method 213.5, an opening that is exposed and larger than 6.4 mm before the test must not become smaller during the test as a result of the movement of the seating surface relative to the other parts of the restraint system.

Information

Marginal note:Information

  •  (1) Every restraint system for infants with special needs must have stitched onto it, indelibly moulded into or onto it, or indelibly printed on a label affixed to it in a permanent manner, the following information:

    • (a) the name and principal place of business of the company that manufactured, imported or sold the restraint system;

    • (b) the model name and number of the restraint system;

    • (c) the date of manufacture of the restraint system, as shown in Schedule 5, with the year, month and day above the corresponding wording in both official languages;

    • (d) a statement indicating — in units based on the International System of Units followed by the corresponding imperial units in parentheses — the mass and height range of the infants for whom the manufacturer recommends the restraint system;

    • (e) a warning indicating

      • (i) that the restraint system must be used only in a forward-facing seating position equipped with a vehicle seat belt or, if the restraint system is equipped with a lower connector system, in a forward-facing seating position equipped with a vehicle seat belt or a lower universal anchorage system,

      • (ii) that the restraint system must be in a rear-facing position, except that a car bed must be used in a flat position along the vehicle’s rear bench seat with the head of the infant towards the centre of the vehicle,

      • (iii) if the restraint system is equipped with a lower connector system, that the restraint system must be secured to the vehicle as shown in the installation instructions by either of the following means and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap:

        • (A) the lower connector system, if the restraint system is installed in a seating position that is equipped with a lower universal anchorage system, or

        • (B) a vehicle seat belt, if the restraint system is installed in a seating position that is not equipped with a lower universal anchorage system,

      • (iv) if the restraint system is not equipped with a lower connector system, that the restraint system must be secured to the vehicle as shown in the installation instructions by means of a vehicle seat belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap, and

      • (v) if the restraint system is equipped with belts for restraining an infant, that the belts must be snugly adjusted around the infant; and

    • (f) an installation diagram that shows the restraint system

      • (i) installed as recommended by the manufacturer in a seating position that is equipped only with a lap belt and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap,

      • (ii) installed as recommended by the manufacturer in a seating position that is equipped only with a continuous-loop lap and shoulder belt, and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap, and

      • (iii) if the restraint system is equipped with a lower connector system, installed as recommended by the manufacturer in a seating position that is equipped with a lower universal anchorage system, and secured to the vehicle by means of the lower connector system and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap.

  • Marginal note:Official languages and print size

    (2) The information referred to in subsection (1) must be in both official languages and in characters of at least 10 points, except for the words “year/année”, “month/mois” and “day/jour” under the date of manufacture, which may be in characters of at least 8 points.

  • Marginal note:Visibility of information

    (3) The information referred to in paragraphs (1)(d) to (f) must be fully visible at all times, even when the restraint system is occupied, whether the restraint system is installed with or without a removable base.

 
Date modified: